tow FIAT 500L 2018 Owner handbook (in English)
[x] Cancel search | Manufacturer: FIAT, Model Year: 2018, Model line: 500L, Model: FIAT 500L 2018Pages: 268, PDF Size: 4.87 MB
Page 16 of 268
WARNING
1)Button B fig. 4should only be pressed
when the key is away from the body, in
particular from the eyes and from objects
that can be spoilt (e.g. clothes). Do not
leave the key unattended to avoid the
button being accidentally pressed while it
is being handled, e.g. by a child.
2)Once the safe lock system is engaged, it
is impossible to open the doors from
inside the car. Therefore, before getting out
of the car check that there is no-one left
on board.
WARNING
1)The electronic components inside the
key may be damaged if the key is
subjected to strong shocks. In order to
ensure complete efficiency of the
electronic devices inside the key, it should
never be exposed to direct sunlight.
WARNING
1)Used batteries should be disposed of,
as specified by law, in the special
containers, otherwise take them to a Fiat
Dealership, which will deal with their
disposal.
IGNITION DEVICE
3) 4) 5) 6)
The key can be turned to three different
positions fig. 6:
STOP: engine off, key can be
removed, steering column locked.
Some electrical devices (e.g. central
door locking system, etc.) can operate;
MAR: driving position. All electrical
devices are enabled;
AVV: engine starting.
The ignition device is fitted with a safety
system that requires the ignition key
to be turned back to STOP if the engine
does not start, before the starting
operation can be repeated.STEERING LOCK
Engagement: when at STOP, remove
the key and turn the steering wheel until
it locks.
Disengagement:move the steering
wheel slightly as you turn the ignition
key to MAR.
WARNING
3)If the ignition device has been tampered
with (e.g. an attempted theft), have it
checked by a Fiat Dealership before driving
again.
4)Always remove the key when you leave
your car to prevent someone from
accidentally operating the controls.
Remember to engage the handbrake.
Engage 1
stgear if the car is parked uphill or
reverse if the car is parked downhill. Never
leave children unattended in the vehicle.
5)It is absolutely forbidden to carry out any
after-market operation involving steering
system or steering column modifications
(e.g.: installation of anti-theft device) that
could badly affect performance and safety,
invalidate the warranty and also result in
non-compliance of the car with type-
approval requirements.
6)Never remove the key while the car is
moving. The steering wheel would
automatically lock as soon as you try to
turn it. This holds true for cars being towed
as well.
6F0Y0654C
14
KNOWING YOUR CAR
Page 18 of 268
IMPORTANT Do not place objects
heavier than 3 kg on the supporting
surface: for safety reasons the
supporting surface is detached from its
housing when subject to higher loads.
The back of the front passenger seat
carries a sign fig. 11 which warns
the rear passengers NOT to travel with
the seat back folded down.REAR SEATS
Longitudinal adjustment
Raise lever A fig. 12, gripping it in the
central area and push the seat forwards
or backwards.
Backrest angle adjustment
Raise lever B fig. 13 and adjust, using
your torso to move the backrest into
position.THIRD-ROW REAR SEATS
(500L WAGON versions)
11) 12)
Some versions feature two "fold-away"
seats behind the rear seats (see fig.
14). These seats stow away to provide
a larger luggage compartment.
Access to the third row of rear
seats
Proceed as follows:
completely lower the head restraints
of the second row rear seat and move
the seat belts to the side, making
sure that they are correctly extended
and not twisted;
operate lever A fig. 12 to move the
second row seat forwards;11F0Y0887C
12F0Y0074C
13F0Y0259C
14F0Y0375C
16
KNOWING YOUR CAR
Page 27 of 268
If the front and rear fog lights are on
when the engine is stopped, they will
switch off. When the engine is
restarted, the fog lights will remain off
until switched on again by pressing the
button.
AUTOMATIC LIGHTING
CONTROL (AUTOLIGHT)
(dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor located
on the windscreen, which detects
variations in outside light levels.
Activation: turn ring nut A fig. 27 to
.
With dusk sensor active, with daytime
running lights (DRL) on, it is not
possible to keep the main beam
headlights on constantly; only flashing
is permitted. In these conditions, the
main beam headlights can be turned on
by turning the ring nut to
and
pushing the stalk towards the
dashboard; otherwise, wait until the
dusk sensor indicates a low light level
(dipped beam headlights on).
On automatic sensor controlled
deactivation, the dipped beam
headlights are deactivated first,
followed by the side lights a few
seconds later.IMPORTANT The sensor cannot detect
the presence of fog. These lights must
therefore be switched on manually in
these circumstances.
MAIN BEAM HEADLIGHTS
With ring nut in position
, push the
stalk forward toward the dashboard
(stable position) to turn on the lights.
The
warning light switches on
in the instrument panel.
The lights are switched off by pulling
the stalk towards the steering wheel.
FLASHING
Pull the left stalk fig. 29 toward yourself,
to the stable position; the stalk goes
back to the central stable position when
it is released. With main beam
headlights on, the
warning light on
the instrument panel will come on at
the same time.DIRECTION INDICATORS
Place the lever in the (stable) position:
upwards:right-hand direction indicator
activation/downwards:left-hand
direction indicator activation.
The
orwarning light will blink on
the instrument panel.
The direction indicators switch off
automatically when the steering wheel
is straightened.
"Lane change" function
If you wish to signal a lane change,
place the left stalk in the unstable
position for less than half a second. The
direction indicator on the side selected
will flash five times and then switch
off automatically.
“Cornering lights”
When the dipped beam headlights are
on and the speed is below 40 km/h,
if the steering wheel rotation angle
is large or the direction indicators are
on, a light (incorporated in the fog light)
will come on on the relevant side to
improve visibility at night time.
29F0Y0771C
25
Page 28 of 268
COURTESY LIGHTS
The function can be enabled and its
times set use the "Settings" Menu
of theUconnect™system. When the
doors are unlocked, the side lights
and puddle lights come on for the time
set in the menu.
Once any door is opened, the lights
remain on for a further 180 seconds, or
for a further 10 seconds after the door
is closed.
“FOLLOW ME HOME”
DEVICE
This allows the space in front of the car
to be lit for a set time.
Activation
With the key turned to STOP or
removed, pull the left-hand stalk
towards the steering wheel within 2
minutes from when the engine is turned
off. Each time the stalk is operated,
the lights stay on for an extra 30
seconds up to a maximum of 210
seconds. When this time is up the lights
automatically switch off.Each time the stalk is operated, the
warning light
on the instrument
panel switches on. The display shows a
message and the time set for the
function. The
warning light comes
on when the stalk is first operated
and stays on until the function is
automatically deactivated.
Deactivation
Keep the stalk pulled towards the
steering wheel for more than 2
seconds.
WARNING
20)The daytime running lights are an
alternative to the dipped beam headlights
for driving during the daytime in countries
where it is compulsory to have lights on
during the day; where it is not compulsory,
the use of daytime running lights is
permitted.
21)Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels. The use of
daytime running lights is governed by the
Highway Code of the country in which you
are driving. Comply with legal
requirements.
INTERIOR LIGHTS
FRONT CEILING LIGHT
Switch A fig. 30 is used to switch on/off
the roof light bulbs.
Switch A positions:
central position: lights C and E
switch on/off when the doors are
opened/closed;
pressed to the left (position OFF):
lights C and E are always switched off;
pressed to the right (position):
lights C and D are always switched on.
The lights switch on/off progressively,
controlled by a timer, when the driver
enters and exits the car.
30F0Y0098C
26
KNOWING YOUR CAR
Page 29 of 268
WINDSCREEN
WIPER/REAR
WINDOW WIPER
WINDSCREEN WIPER /
WASHER
6) 7)
This operates only with the ignition key
turned to MAR.
Ring A fig. 31 has five different
positions:
windscreen wiper off
constant flick with 10 second
periods
“faster” flick (speed related)
LOcontinuous slow operation
HIcontinuous fast operation
MIST functionMove the stalk upwards (unstable
position) to activate the MIST
function: operation is limited to the
time for which the stalk is held in this
position. When released, the stalk
will return to its default position and the
windscreen wiper will be stopped.
This function is useful to remove small
deposits of dust from the windscreen,
or morning dew.
“Smart washing” function
Pull the stalk towards the steering
wheel (unstable position) to operate the
windscreen washer. When the stalk is
held pulled for longer than half a
second, the windscreen wiper is moved
with active control.
The wipers flick three times when the
stalk is released, after which, if the
control is in position
, the washing
cycle is concluded by one last flick after
a pause of approximately 6 seconds.
With the ring inLOorHIposition,
the smart washing function is not
carried out.
Raising the blades ("Service
position" function)
This function makes it possible to
replace the blades or protect them in
conditions of ice and/or snow.Function activation
turn the ring A to position(wiper
stopped);
turn the ignition key to the STOP
position;
after having turned the ignition key
to the STOP position, within two
minutes move the lever to the MIST
within two minutes for at least half a
second to activate the wiper for part
of a flick. This operation can be
repeated up to three times, in order to
move the blade to the most suitable
position for replacement;
turn the ignition key to the MAR
position to move the blades back
down.
The function will be deactivated when
the engine is started again, in case of a
wiping request or with the car moving
(speed above 5 km/h).
IMPORTANT Place the blades back in
contact with the windscreen before
activating the windscreen wiper again
and/or turning the ignition key to
MAR-ON.
IMPORTANT Before activating the
function, make sure, when starting the
engine, that the windscreen is free of
snow or ice.
31F0Y0608C
27
Page 30 of 268
RAIN SENSOR
(for versions/markets, where provided)
22)8) 9)
This is located behind the rear-view
mirror in contact with the windscreen.
The sensor is activated with ignition key
turned to the MAR position, while it is
deactivated with the key turned to
STOP position.
The sensor can measure the amount of
rain and, consequently, manage the
automatic wiping mode of the
windscreen in accordance with the
amount of water on the screen (see the
“Automatic Wiping” paragraph).
AUTOMATIC WIPING
Activation
Go to the “Settings” menu of the
Uconnect™system (for more
information see the supplement
available online) and turn the ring A to
position
or.
Inhibition
If the ignition key is turned to STOP,
leaving the ring A in position
or,
when the engine is next started (ignition
device at MAR), no wiping cycle
occurs for system protection reasons.Deactivation
Go to the “Settings” menu of the
Uconnect™system (for more
information see the supplement
available online) and turn the ring A to a
position other than intermittent (
or
).
REAR WINDOW WIPER /
WASHER
10)
This operates only with the ignition key
turned to MAR.
The ring B fig. 32 can be set to the
following positions:
rear window wiper stopped
intermittent operation
continuous operation, without
pausing between two strokes.The rear window wiper can be
activated in the following ways:
intermittent(with a two-second
pause between two flicks), when ring B
is in position
and the windscreen
wiper is not in operation;
synchronous(half frequency as
the windscreen wiper), when ring B is in
position
and the wiper is working or
when ring B is in position
, reverse
gear is engaged and the windscreen
wiper is working;
continuouswhen ring nut B is in
position
or when reverse gear is
engaged.
Push the stalk towards the dashboard
(rocking position) to activate the rear
window washer jet. Keep pushing the
lever to automatically activate both
the rear window washer jet and the rear
window wiper with a single movement.
Releasing the stalk will activate three
strokes, as described for the
windscreen wiper. If the position is
(rear window wiper stopped), after a
6 second pause, the washing cycle
is completed by a single stroke. The
smart wash cycle will not be performed
if the ring B is in position
.
If washer lasting longer than 30
seconds is needed, the washing cycle
will be inhibited as described in the
“Smart washing” paragraph.
32F0Y0655C
28
KNOWING YOUR CAR
Page 32 of 268
hold down button Afig. 33: after
approximately 10 seconds the curtain
moves jerkily to closing position. When
the movement stops (blind closed),
release button A (if the blind is already
closed, you will hear the mechanical
lock only);
press button A again within 3
seconds after the blind reached the fully
closed position;
hold down button A: the blind will
perform an automatic opening and
closing cycle. Should this not occur,
repeat the operation from the
beginning;
hold down button A until the blind is
completely closed: the initialisation
procedure has ended.
ELECTRIC SUNROOF
(for versions/markets, where provided)
23)11)
The sun roof and the blind can be
operated only with the ignition
key turned to MAR.
CONTROL BUTTONS
Opening/closing the front glass
panel
Opening
Press button A fig. 35 to open the sun
roof in the “spoiler” position. After
opening in “spoiler” position, press
button A once again for more than half
a second to bring the roof automatically
to fully open position. To deactivate
the automatic movement press the
button again. Use button A in jog mode
to open the sun roof manually.Closing
From the fully open position press
button A for more than half a second:
the front glass panel will move into
the “spoiler” position. Use button A in
jog mode to close the sun roof
manually.
Sun blind movement
Pressing the B fig. 35 button will move
the blind towards the rear part of the
vehicle, until it is fully open. With blind
fully open press button B: the blind
will move towards the front part of the
vehicle, until it is fully closed. During the
blind automatic opening and closing
stages, press the button again to
interrupt the blind movement.
Button B can be pressed in jog mode
to open or close the blind manually.
EMERGENCY OPERATION
If the control buttons fail to operate, the
sunshade and the sunroof can be
moved manually proceeding as
described below:
Sun blind movement: remove
protective cap A fig. 36 on the internal
trim;
Sunroof movement: remove
protective cap B on the internal trim;
35F0Y0120C
30
KNOWING YOUR CAR
Page 39 of 268
Position 1 (platform at threshold
level)
Position 2 (platform completely
raised)
Load platform tilting
The load platform can be located in
oblique position (tilted towards the rear
seat backrests, see fig. 47), in order
to facilitate access to the area
underneath the luggage compartment
(e.g. to pick up the space saver wheel
or the "Fix&Go Automatic" kit).
In addition, in this position, the platform
allows any object in the luggage
compartment to be correctly blocked,
preventing them from sliding in the case
of sharp braking.LUGGAGE-COVERING
CURTAIN
(500L WAGON versions)30)15)
Luggage-covering curtain A fig. 48 can
be rolled up and removed.
Rolling up the blind: take hold of
handle C and then release pins B fig.
49(one for each side) from their seats.
Then accompany the blind to the rear
of the luggage compartment.Removing the blind:roll up the blind
then pull the two hooks A fig. 50 (one
on each side) towards the inside of the
luggage compartment. Then lift the
blind up and remove it.
WARNING
27)Be careful not to hit objects on the
storage shelf when you open the tailgate.
28)Make sure the backrest is properly
secured at both sides to prevent it moving
forward in the event of sharp braking,
with possible impact with the occupants.
29)Do not move the seat if a child is
seated on the same or sitting in the
suitable child restraint system.
30)In the event of an accident or sharp
braking, any object placed on the curtain
may be projected backwards in the
passenger compartment, and risk to hurt
the occupants.
47F0Y0609C
48F0Y0371C
49F0Y0373C
50F0Y0374C
37
Page 42 of 268
In Italy, the tank has a life of 10 years
starting from the car registration date. If
the vehicle has been registered in a
country other than Italy, the duration
and the testing/inspection procedures
of the LPG tank can vary depending on
the national laws of that country. In all
case, when the time limit for your
country has expired, go to a Fiat Dealer
to have the tank replaced.
SELECTION OF
PETROL/LPG SUPPLY
TYPE
The fig. 55 button (petrol/LPG switch)
allows you to select running on petrol or
LPG.
If, during LPG operation, the same runs
out, the car switches to petrol
automatically and all the bars near the
letters LPG on the display switch off.
This condition persists until the next
LPG refuelling.The engine always starts up on petrol,
with automatic switching to LPG when
the best conditions are achieved
(engine water temperature, minimum
engine rpm limit) for switching to LPG.
REFUELLING
LPG
Maximum refuelling capacity (including
reserve): 38.4 litres. The figure already
takes into account the 80% tank filling
limit and the residual fluid required
for priming; this figure represents the
maximum permitted capacity.In
addition, this value may, in different
refuelling situations, give rise to
variations as a result of: differences
between the supply pressures of
the pumps, pumps with different
supply/stopping specifications,
tank not in reserve condition.
IMPORTANT In order to avoid
inconsistent information by the LPG
gauge on the instrument panel, it is
recommended to refill with at least 10
litres each time.
WARNING
34)Note that in some countries (including
Italy) there are legal restrictions in force
for parking/garaging motor vehicles fuelled
by gas that is denser than air; LPG comes
under this category.
35)Do not switch between the two
operating modes whilst starting the engine.
36)If gas is smelt, switch from LPG
operation to petrol operation and
immediately go to a Fiat Dealership to have
the vehicle checked and possible system
faults excluded.
WARNING
16)The car is equipped with a specifically
designed gaseous LPG injection system:
it is therefore absolutely forbidden to
alter the configuration of the system or its
components. The use of other
components or materials could cause
malfunctions and lead to a reduction
in safety; therefore, in the case of
problems, contact a Fiat Dealership. When
towing or lifting the vehicle, follow the
instructions in the main handbook under
the paragraph on "Towing the vehicle"
to prevent damage to the gas system
parts.
17)The system operates at temperatures
ranging between -20°C and 100°C.
55F0Y0657C
40
KNOWING YOUR CAR
Page 45 of 268
To guarantee switching in full safety, the
actual change to the chosen fuel
system takes place depending on the
car usage conditions; it may not
therefore be immediate.
In addition, when starting at outside
temperatures below approximately
-10°C, the switching times from petrol
to methane increase to allow the
pressure regulator/reduction unit to
heat up.
WARNING
37)The car is equipped with a high-
pressure methane system designed to
operate at 200 rated bar. It is dangerous to
force the system to run at higher
pressures. When towing or lifting the car,
follow the instructions in the "Towing
the car" paragraph to prevent damage to
the methane system parts. If there is a fault
in the methane system, only contact a
Fiat Dealership. Do not modify
configuration or components of the
methane system; they have been designed
exclusively for this car. The use of other
components or materials could cause
malfunctions and prejudice safety.38)When oven painting, the cylinders must
be removed from the vehicle and
subsequently refitted by a Fiat Dealership.
Although the methane system has
numerous safety features, it is advisable to
close the manual cocks for the cylinders
every time the car is not in use for a long
period, transported on other cars or moved
in an emergency as a result of a fault or
accident.
39)Do not switch between the two
operating modes whilst starting the engine.
40)If gas is smelled, switch from methane
operation to petrol operation and
immediately go to a Fiat Dealership to have
the vehicle checked and possible system
faults excluded.
WARNING
23)If, during methane operation, the same
runs out, the car switches to petrol
automatically and all the bars near the
letters CNG on the display switch off. This
display remains until the next methane
refuelling.
24)Regardless of the last fuel system
used, at the following engine starting, after
the initial petrol stage, the system will
automatically switch to methane.
25)When switching from petrol to methane
is requested, a metal noise from the valves
which pressurise the circuit can be heard,
as it happens while starting the car. For the
switching logics described above, a delay
between the valve ticking and the switching
off of the green warning light
is
absolutely normal.26)In particular usage conditions, such as
starting and operation at low ambient
temperature, the system may switch
temporarily to petrol operation, without
indicating the performed switching. In the
event of low methane levels in the tank
or request for high performance (e.g.
overtaking, car fully laden, steep hills) the
system may automatically switch to petrol
operation to guarantee the engine power
requested; the green icon
switches
on to indicate this. When the above
conditions are no longer present, the
system automatically restores methane
operation. The green warning light
turns
off. To achieve the automatic switching
described above, make sure that there is
always enough fuel in the petrol tank.
27)The other plates (provided with the
vehicle documents) show the date when
the first cylinder inspection/test is due.
Methane refuelling stations are not
authorised to refill the cylinders when the
inspection date has expired.
43