warning FIAT 500X 2014 2.G Owners Manual

WARNING!(Continued)
warned not to touch the parking brake, brake
pedal or the transmission gear selector.
• Do not leave the key fob in or near the vehicle (or
in a location accessible to children), and do not
leave the ignition in the ACC or ON/RUN mode.
A child could operate power windows, other
controls, or move the vehicle.
CAUTION!
• Before moving the transmission gear selector out
of PARK, you must start the engine, and also
press the brake pedal. Otherwise, damage to the
gear selector could result.
• DO NOT race the engine when shifting from
PARK or NEUTRAL into another gear range, as
this can damage the drivetrain.
The following indicators should be used to ensure that
you have engaged the transmission into the PARK
position:
• When shifting into PARK, press the lock button on
the gear selector, and firmly move the gear selector
all the way forward until it stops and is fully seated. •
Look at the transmission gear position display and
verify that it indicates the PARK position (P), and is
not blinking.
• With the brake pedal released, verify that the gear
selector will not move out of PARK.
Reverse (R)
This range is for moving the vehicle backward. Shift
into REVERSE only after the vehicle has come to a
complete stop.
Neutral (N)
Use this range when the vehicle is standing for pro-
longed periods with the engine running. The engine
may be started in this range. Apply the electric park
brake and shift the transmission into PARK if you must
leave the vehicle.
WARNING!
Do not coast in NEUTRAL and never turn off the
ignition to coast down a hill. These are unsafe
practices that limit your response to changing traf-
fic or road conditions. You might lose control of the
vehicle and have a collision.
7
STARTING AND OPERATING 231

CAUTION!
Towing the vehicle, coasting, or driving for any
other reason with the transmission in NEUTRAL
can cause severe transmission damage. Refer to
“Recreational Towing” in “Starting And Operating”
and “Towing A Disabled Vehicle” in “In Case Of
Emergency” for further information.
Drive (D)
This range should be used for most city and highway
driving. It provides the smoothest upshifts and down-
shifts, and the best fuel economy. The transmission
automatically upshifts through all forward gears. The
DRIVE position provides optimum driving characteris-
tics under all normal operating conditions.
When frequent transmission shifting occurs (such as
when operating the vehicle under heavy loading con-
ditions, in hilly terrain, traveling into strong head
winds or while towing a heavy trailer), use the
AutoStick shift control (refer to “AutoStick” in this
section for further information) to select a lower gear.
Under these conditions, using a lower gear will im-
prove performance and extend transmission life by
reducing excessive shifting and heat buildup. If the transmission temperature exceeds normal operat-
ing limits, the transmission controller may modify the
transmission shift schedule, reduce engine torque,
and/or expand the range of torque converter clutch
engagement. This is done to prevent transmission dam-
age due to overheating.
If the transmission becomes extremely hot, the “Trans-
mission Temperature Warning Light” may illuminate
and the transmission may operate differently until the
transmission cools down.
During cold temperatures, transmission operation may
be modified depending on engine and transmission
temperature as well as vehicle speed. This feature
improves warm up time of the engine and transmission
to achieve maximum efficiency. Engagement of the
torque converter clutch, and shifts into 8th or 9th gear,
are inhibited until the transmission fluid is warm.
Normal operation will resume once the transmission
temperature has risen to a suitable level.
AutoStick
AutoStick is a driver-interactive transmission feature
providing manual shift control, giving you more control
of the vehicle. AutoStick allows you to maximize engine
braking, eliminate undesirable upshifts and downshifts,
232 STARTING AND OPERATING

AutoStick position at any time without taking your foot
off the accelerator pedal.
WARNING!
Do not downshift for additional engine braking on
a slippery surface. The drive wheels could lose their
grip and the vehicle could skid, causing a collision
or personal injury.
Transmission Limp Home Mode
Transmission function is electronically monitored for
abnormal conditions. If a condition is detected that
could result in transmission damage, Transmission
Limp Home Mode is activated. In this mode, the
transmission remains in fourth gear regardless of which
forward gear is selected. PARK, REVERSE, and NEU-
TRAL will continue to operate. The Malfunction Indi-
cator Light (MIL) may be illuminated. Limp Home
Mode allows the vehicle to be driven to an authorized
dealer for service without damaging the transmission.In the event of a momentary problem, the transmission
can be reset to regain all forward gears by performing
the following steps:
1. Stop the vehicle.
2. Shift the transmission into PARK.
3. Cycle the ignition to the STOP/OFF position.
4. Wait approximately 10 seconds.
5. Restart the engine.
6. Shift into the desired gear range. If the problem is no
longer detected, the transmission will return to nor-
mal operation.
NOTE: Even if the transmission can be reset, we
recommend that you visit your authorized dealer at
your earliest possible convenience. Your authorized
dealer has diagnostic equipment to determine if the
problem could recur. If the transmission cannot be reset,
authorized dealer service is required.
234 STARTING AND OPERATING

Activation
Push the on/off button to activate the Speed Control.
The cruise indicator light in the instrument cluster
display will illuminate. To turn the system off, push the
on/off button a second time. The cruise indicator light
will turn off. The system should be turned off when not
in use.
WARNING!
Leaving the Speed Control system on when not in
use is dangerous. You could accidentally set the
system or cause it to go faster than you want. You
could lose control and have an accident. Always
leave the system off when you are not using it.
Setting A Desired Speed
Turn the Speed Control on.
NOTE:The vehicle should be traveling at a steady
speed and on level ground before pushing the SET (+)
or SET (-) button. When the vehicle has reached the desired speed, push
the SET (+) or SET (-) button and release. Release the
accelerator and the vehicle will operate at the selected
speed.
Deactivation
A soft tap on the brake pedal, pushing the CANC
button, ESC intervention, brake control mitigation, elec-
tronic park brake intervention, or normal brake pres-
sure while slowing the vehicle will deactivate the Speed
Control without erasing the set speed from memory.
Pushing the on/off button or turning the ignition
switch to STOP erases the set speed from memory.
Resume Speed
To resume a previously set speed, push the RES button
and release. Resume can be used at any speed above
20 mph (32 km/h).
Varying The Speed
To Increase Speed
When the Speed Control is set, you can increase speed
by pushing the SET
(+)button.
236 STARTING AND OPERATING

Sport Mode –This mode is designed to increase
steering feedback to the driver with a slight increase in
effort and changes the transmission shift schedules for
more aggressive shifting. This driving mode is useful
while driving on twisty roads where more steering
precision is desired in spirited cornering.
Warning Messages
In the event of a system fault, the system automatically
defaults to Automode and a message will appear in
the instrument cluster display.
Refer to “Instrument Cluster Display” in “Getting To
Know Your Instrument Panel” for further information.
BRAKE CONTROL — IF EQUIPPED
Brake Control
The Brake Control system with mitigation provides the
driver with audible warnings, visual warnings (within
the instrument cluster display), and may apply a brake
jerk to warn the driver when it detects a potential
frontal collision. The warnings and limited braking are
intended to provide the driver with enough time to
react, avoid or mitigate the potential collision. NOTE:
•
Brake Control monitors the information from the
forward looking sensors as well as the Electronic
Brake Controller (EBC), to calculate the probability of
a forward collision. When the system determines that
a forward collision is probable, the driver will be
provided with audible and visual warnings and may
provide a brake jerk warning.
• If the driver does not take action based upon these
progressive warnings, then the system will provide a
limited level of active braking to help slow the
vehicle and mitigate the potential forward collision.
If the driver reacts to the warnings by braking and
the system determines that the driver intends to
avoid the collision by braking but has not applied
sufficient brake force, the system will compensate
and provide additional brake force as required.
Vehicles With A Manual Transmission: After the end
of the intervention of automatic braking, the engine
could stall, unless the driver can depress the clutch
pedal.
Vehicles With Automatic Transmission: After the end
of the intervention of automatic braking, the transmis-
sion may remain in last gear stored: therefore the car
7
STARTING AND OPERATING 239

could lurch forward, once the brakes release a few
seconds later. If the Brake Control event stops the
vehicle completely, the system will hold the vehicle at
standstill for two seconds and then release the brakes.
If a Brake Control event begins at a speed below 20 mph
(32 km/h), the system may provide the maximum
braking possible to mitigate the potential forward col-
lision. If the Brake Control event stops the vehicle
completely, the system will hold the vehicle at standstill
for two seconds and then release the brakes.When the system determines a collision with the vehicle
in front of you is no longer probable, the warning
message will be deactivated.
NOTE:
•
The minimum speed for Brake Control activation is
4 mph (7 km/h).
• The maximum speed for Brake Control activation is
124 mph (200 km/h).
• The Brake Control alerts may be triggered on objects
other than vehicles such as guard rails or sign posts
based on the course prediction. This is expected and
is a part of normal Brake Control activation and
functionality.
• The Brake Control system is intended for on-road use
only. If the vehicle is taken off-road, the Brake
Control system should be deactivated to prevent
unnecessary warnings to the surroundings.
• The active braking is enabled only if the front seat
belts are fastened.
Brake Control Message
240 STARTING AND OPERATING

WARNING!
Brake Control is not intended to avoid a collision
on its own, nor can Brake Control detect every type
of potential collision. The driver has the responsi-
bility to avoid a collision by controlling the vehicle
via braking and steering. Failure to follow this
warning could lead to serious injury or death.
Turning Brake Control On Or Off
The Brake Control menu setting is located in the
Uconnect settings.
NOTE:The default status of Brake Control is “Warning
+ Active Braking.” This allows the system to warn you
of a possible collision with the vehicle in front of you
and enable the active braking.
• Changing the Brake Control status to “Off” deacti-
vates the system, so no warning or active braking
will be available in case of a possible collision
• Changing the Brake Control status to “Only Warn-
ing” prevents the system from providing limited
active braking, or additional brake support if the driver is not braking adequately in the event of a
potential frontal collision, but maintains the audible
and visual warnings.
Changing the status of the system is only possible with
the vehicle at a complete stop.
NOTE: The Brake Control system state is not kept in
memory from one key cycle to the next. If the system is
turned off, it will turn on when the vehicle is restarted.
Changing Brake Control Sensitivity
By changing the settings on the menu of the Uconnect
system, you can change the sensitivity of the system by
choosing one of the following three options: Near,
Medium orFar. Refer to “Multimedia” for further
information.
The default option is Medium. This setting provides
that the system notify the driver of a possible accident
with the vehicle ahead of it when the latter is at a
standard distance, intermediate between the other two
possible settings.
By setting the sensitivity of the system to Far, the
system will warn the driver of a possible accident with
the vehicle in front when the latter is at a greater
distance, giving you the chance to act on the brakes in7
STARTING AND OPERATING 241

a more limited and gradual. This setting gives the
driver the maximum possible time of reaction to pre-
vent a possible accident.
By changing the option toNear, the system will warn
the driver of a possible accident with the vehicle ahead
of it when the latter is a reduced distance. This setting
offers a reaction time to the driver lower than the
settings Medium andFar, in the case of a potential
accident, while a more dynamic driving of the car.
The setting of the sensitivity of the system is maintained
in memory when the engine is switched off.
Brake Control Limited Warning
If the instrument cluster display will read “Brake Con-
trol Limited Functionality” or “Brake Control Limited
Functionality Clean Front Windshield” momentarily,
there may be a condition that limits Brake Control
functionality. Although the vehicle is still drivable un-
der normal conditions, the active braking may not be
fully available. Once the condition that limited the
system performance is no longer present, the system
will return to its full performance state. If the problem
persists, see your authorized dealer.
Service Brake Control Warning
If the system turns off, and the instrument cluster
display displays:
• Brake Control Unavailable Service Required
This indicates there is an internal system fault. Al-
though the vehicle is still drivable under normal con-
ditions, have the system checked by an authorized
dealer.
“Wipe Front Radar Sensor In Front Of Vehicle” Warn-
ing
The “Brake Control Front Radar Sensor Temporarily
Blocked” warning will display when conditions tempo-
rarily limit system performance. This most often occurs
at times of poor visibility, such as in snow or heavy rain.
The system may also become temporarily blinded due
to obstructions, such as mud, dirt or ice. In these cases,
the instrument cluster display will display “Brake Con-
trol Front Radar Sensor Temporarily Blocked” and the
system will deactivate.
The “Brake Control Front Radar Sensor Temporarily
Blocked” message can sometimes be displayed while
driving in highly reflective areas (i.e. tunnels with
reflective tiles, or ice and snow). The system will
242 STARTING AND OPERATING

recover after the vehicle has left these areas. Under rare
conditions, when the radar is not tracking any vehicles
or objects in its path this warning may temporarily
occur.
If weather conditions are not a factor, the driver should
examine the sensor. It may require cleaning or removal
of an obstruction. The sensor is located behind the
lower grille. In absence of visible obstructions on the
bumper, it could be necessary to wipe off the radar
directly on the surface, after having the radar cover
removed. It’s recommended that your authorized
dealer perform’s this operation.
NOTE:
•If the “Brake Control Front Radar Sensor Temporar-
ily Blocked” message occurs frequently (e.g. more
than once on every trip) without any snow, rain,
mud, or other obstruction, have the radar sensor
realigned at your authorized dealer.
• Installing a snow plow, front-end protector, an after-
market grille or modifying the grille is not recom-
mended. Doing so may block the sensor and inhibit
Brake Control operation.Precautions While Driving With Brake Control
In certain driving conditions, such as:
• Driving in the vicinity of a curve
• Small vehicles and/or not aligned to the lane
• Lane changing of other vehicles
• Passing of vehicles in an oncoming intersection
The intervention of the system could be unexpected or
delayed. The driver must therefore always pay particu-
lar attention, while maintaining control of the car to
drive in complete safety.
7
STARTING AND OPERATING 243

•Clean the Rear ParkSense sensors regularly, taking
care not to scratch or damage them. The sensors must
not be covered with ice, snow, slush, mud, dirt or
debris. Failure to do so can result in the system not
working properly. The Rear ParkSense system might
not detect an obstacle behind the fascia/bumper, or it
could provide a false indication that an obstacle is
behind the fascia/bumper.
• Objects such as bicycle carriers, etc., must not be
placed within 12 inches (30 cm) from the rear fascia/
bumper while driving the vehicle. Failure to do so
can result in the system misinterpreting a close object
as a sensor problem, causing a failure indication to be
displayed in the instrument cluster.
WARNING!
• Drivers must be careful when backing up even
when using ParkSense. Always check carefully
behind your vehicle, look behind you, and be
sure to check for pedestrians, animals, other ve-
hicles, obstructions, and blind spots before back-
ing up. You are responsible for safety and must
continue to pay attention to your surroundings.
(Continued)
WARNING! (Continued)
Failure to do so can result in serious injury or
death.
• Before using ParkSense, it is strongly recom-
mended that the ball mount and hitch ball assem-
bly is disconnected from the vehicle when the
vehicle is not used for towing. Failure to do so can
result in injury or damage to vehicles or obstacles
because the hitch ball will be much closer to the
obstacle than the rear fascia when the loud-
speaker sounds the continuous tone. Also, the
sensors could detect the ball mount and hitch ball
assembly, depending on its size and shape, giving
a false indication that an obstacle is behind the
vehicle.
CAUTION!
• ParkSense is only a parking aid and it is unable to
recognize every obstacle, including small ob-
stacles. Parking curbs might be temporarily de-
tected or not detected at all. Obstacles located
(Continued)
250 STARTING AND OPERATING