wheel bolts FIAT BRAVO 2009 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: BRAVO, Model: FIAT BRAVO 2009 2.GPages: 246, PDF Size: 4.1 MB
Page 159 of 246
158
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
The jack shall only be used
for changing wheels on the
car with which it is provided or on
cars of the same model. It must not
be used for other purposes such as for
instance raising cars of other models.
In no case should it be used for repairs
under the car. Incorrect positioning
of the jack may cause the jacked car
to fall. Do not use the jack for high-
er capacities than stated on its label.
Snow chains cannot be fitted to the
space-saver spare wheel. So, if a front
(drive) wheel is punctured and chains
are needed, a rear wheel should be
fitted to the front of the car and the
spare wheel should be fitted to the
rear. This way with two normal dri-
ve wheels, snow chains can be fitted
to them to solve an emergency.
WARNING
Fasten the wheel cap cor-
rectly to prevent the wheel
from coming free in motion. Never
tamper with the inflation valve. Nev-
er place tools between the rim and
tyre. Check and restore, if required,
the pressure of tyres and spare wheel
to the values given in section “Tech-
nical specifications”.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of the car
changes. Avoid accelerating or brak-
ing sharply, abrupt turns or fast cor-
nerings. The life of the spare wheel
is approx. 3000 Km, after this dis-
tance it should be replaced with an-
other of the same type. Never at-
tempt to fit a conventional tyre on a
rim designed for use as a space-saver
spare wheel. Have the punctured
wheel repaired and refitted as soon
as possible. Two or more space-saver
spare wheels should never be used to-
gether. Do not grease the threads of
bolts before installing them: they
might slip out.
WARNING
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 158
Page 161 of 246
160
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒undo the wheel bolts and remove the
wheel.
❒make sure the contact surfaces be-
tween spare wheel and hub are clean
so that the fastening bolts will not come
loose;
fig. 6F0M0395m
❒warn anybody nearby that the car is
about to be lifted. They must stay clear
and not touch the car until it is back on
the ground;
❒fit the handle R-fig. 6to operate the
jack and raise the car until the wheel
is a few centimetres from the ground;
❒using the wrench provided L-fig. 5
loosen the fastening bolts by about one
turn; if the car is fitted with alloy rims,
shake the car to facilitate removing this
rim from the wheel hub;
❒work the jack crank M-fig. 6to extend
it until the groove Non the upper part
of the jack is correctly inserted on the
lower profile Pof the body in point Q
(at approx. 72 cm from the front wheel
centre or 75 cm from rear wheel cen-
tre);
fig. 5F0Q0394m
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 160
Page 162 of 246
161
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
❒install the space-saver spare wheel
matching the holes S-fig. 7with the
corresponding pins T;
❒using the wrench provided, fully tight-
en the four fastening bolts;
❒work the jack handle R-fig.6to lower
the car and remove the jack;
❒using the wrench provided, tighten up
the wheel bolts in a criss-cross fashion
following the sequence shown in fig. 8.REFITTING THE STANDARD
WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
For versions with steel rim
Proceed as follows:
❒ Make sure the contact surfaces be-
tween standard wheel and hub are
clean so that the fastening bolts will not
come loose;
❒Fit the normal wheel matching the
holes S-fig. 7with the corresponding
pins T;
❒Using the wrench provided, tighten the
fastening bolts;
❒ Lower the car and remove the jack;
❒Using the wrench provided, fully tight-
en the bolts in the sequence shown in
fig. 8;
❒Place the cap near the wheel so that the
inflation valve can come through the
slot provided on the cap;
❒Press the circumference of the cap,
starting from the parts nearest the in-
flation valve until it is inserted com-
pletely.
IMPORTANT Incorrect fitting may cause
the wheel cap to come off when the car is
travelling.
fig. 7F0Q0396mfig. 8F0Q0397m
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 161
Page 163 of 246
162
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
When you have finished
❒Stow the space-saver spare wheel
G-fig. 10in the space provided in the
boot;
❒Insert the partially open jack into the
container Fand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒Put the tools back into their places in
the container;
❒Stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device E;
❒Correctly reposition the boot stiff cov-
er.
fig. 10F0Q0392m
Versions with alloy rims
Proceed as follows:
❒tighten pin A-fig. 9in one of the holes
of the wheel hub fastening bolts;
❒Insert the wheel on the pin and, using
the wrench provided, tighten the bolts
available. This is facilitated by the ex-
tension provided B;
❒Loosen the pin Aand tighten the last
fastening bolt;
❒Lower the car and remove the jack;
❒Using the wrench provided, fully tight-
en the bolts in the sequence shown
previously for the space-saver spare
wheel (see fig. 8).
❒refit the hubcap.
fig. 9F0Q0217m
155-190 BRAVO GB.qxd 11-11-2009 10:55 Pagina 162