bulb FIAT BRAVO 2015 2.G Owners Manual

EXTERNAL LIGHT FAILURE
(amber)
The warning light switches on when a fault is
detected on one of the following lights:
❒ side lights
❒ brake (stop) lights or corresponding fuse (see the
description provided for this symbol
).
❒ rear fog lights
❒ direction indicators
❒ number plate lights.
The failure relating to these lights could be: one or
more blown bulbs, a blown protection fuse or a
break in the electrical connection.
The display will show the dedicated message.
REAR FOG LIGHTS (amber)
The warning light switches on when the rear fog
lights are activated.
FRONT FOG LIGHTS (green)
The warning light comes on when the front fog lights
are turned on.LEFT-HAND DIRECTION
INDICATOR (green) (intermittent)
The warning light comes on when the direction
indicator control stalk is moved downwards
or, together with the right-hand direction indicator,
when the hazard warning light button is pressed.RIGHT-HAND DIRECTION
INDICATOR (green) (intermittent)
The warning light switches on when the direction
indicator control stalk is moved upwards or, together
with the left direction indicator, when the hazard
warning light button is pressed.
158GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

CHANGING A BULBGENERAL INSTRUCTIONS
❒Before changing a bulb check the contacts for
oxidation;
❒ Burnt bulbs must be replaced by others of the
same type and power;
❒ after replacing a headlight bulb, always check its
alignment;
❒ when a light is not working, check that the
corresponding fuse is intact before changing a bulb.
For the location of fuses, refer to the paragraph
“If a fuse blows” in this section;
WARNING
Modifications or repairs to the electric
system that are not carried out properly
or do not take the system technical
specifications into account can cause
malfunctions leading to the risk of fire.WARNING
Halogen bulbs contain pressurised gas,
in the case of breakage they may burst .
Halogen bulbs must be handled holding
the metallic part only.Touching the
transparent part of the bulb with your
fingers may reduce the intensity of the emitted
light and even reduce the lifespan of the bulb. In
case of accidental contact , wipe the bulb with
a cloth moistened with alcohol and let the bulb
dr y.If possible, we recommend have bulbs
replaced by a Fiat Dealership.The correct
operation and aiming of the outer lights
are absolutely essential for the safety of the car
and of compliance with law.Due to the high supply voltage, gas
discharge bulbs (Bi-Xenon) (for versions/
markets, where provided) must only be
replaced by a specialist technician: danger of
death! Contact a Fiat Dealership.
IMPORTANT When the weather is cold or damp or
after heavy rain or washing, the surface of headlights
or rear lights, may steam up and/or form drops of
condensation on the inside. This is a natural
phenomenon due to the difference in temperature
and humidity between the inside and the outside
of the glass which does not indicate a fault and does
not compromise the normal operation of lighting
devices. The mist disappears quickly when the lights
are turned on, starting from the centre of the
diffuser, extending progressively towards the edges.
174GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

TYPES OF BULBSVarious types of bulbs are fitted to your car:
All-glass bulbs:(type A) press-fitted. Pull to remove.Bayonet type bulbs: (type B) to remove them press the
bulb and turn it anticlockwise.
Tubular bulbs: (type C) release them from their contacts
to remove.
Halogen bulbs: (type D) to remove the bulb, release the
clip holding the bulb in place.
Halogen bulbs: (type E) to remove the bulb, release the
clip holding the bulb in place.
Gas discharge bulb (Xenon): (type F) to replace them
contact a Fiat Dealership.
175GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

BulbsUseTypePowerRe. Figure
Main beam headlights H155 W E
Longlife dipped headlights H155 W D
Dipped headlights with gas discharge bulbs
(for versions/markets, where provided) D2R
35 W F
Longlife front side lights W5W5 W A
Front fog lights (for versions/markets, where provided) H11 55 WE
Front direction indicators PY24W24W B
Side direction indicators WY5W5 WA
Rear direction indicators R10W10 W B
Rear side lights/rear fog lights P5/21W 5 W/21 WB
Rear side lights/break lights P5/21W 5 W/21 WB
Third brake light (additional brake light) W2.3W2.3 W A
Reverse lights P21W21 W B
Number plate lights W5W5 W A
Front roof light C10W2x10 W C
Rear roof light (for versions/markets, where provided) C10W 10 WC
Glove compartment light C5W5W C
Luggage compartment roof light W5W5WA
Courtesy mirror lights (for versions/markets, where
provided) C5W
5 W C
176GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REPLACING EXTERIOR BULBSFor the type of bulb and power rating, see “Changing
a bulb" paragraph.
FRONT LIGHT CLUSTERS
The front light clusters contain side lights, dipped
headlights, main beam headlights and direction
indicator bulbs.
The bulbs are arranged inside the light cluster as
follows fig. 139:A
Side lights/daytime running lights and main beam
headlights
BDipped headlightsC
Direction indicatorsDIPPED HEADLIGHTS
To change the bulb, proceed as follows:
❒
remove the protective cover B fig. 139;
❒ release the bulb holding clip A fig. 140;
❒ disconnect the electrical connector B;
❒ remove bulb C and replace it;
❒ fit the new bulb, ensuring that the outline of the
metal part coincides with the splining on the
curve of the headlight. Then reconnect the
electrical connector B and reattach the bulb
holding clip A;
❒ refit the protective cover A fig. 139.fig. 139
F0Q0704
fig. 140
F0Q0705
177GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

With gas discharge bulbs (Bi-Xenon)
(for versions/markets, where provided)
WARNING
Due to the high power supply voltage,
gas discharge bulbs (Bi-Xenon) should
only be replaced by specialised personnel:
danger of death! Contact a Fiat Dealership. SIDE LIGHTS
To change the bulb, proceed as follows:
❒
remove the protective cover A fig. 139;
❒ turn the bulb holder A fig. 141 anticlockwise and
remove it;
❒ remove the bulb B and replace it;
❒ refit the new bulb, put the bulb holder A fig. 141
back into place and then refit the protective cover
B fig. 139 properly.
fig. 141
F0Q0706
178GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover A fig. 139;
❒ release the bulb holding clip A fig. 142;
❒ remove bulb C and replace it;
❒ fit the new bulb, ensuring that the outline of the
metal part coincides with the splining on the
curve of the headlight. Then reconnect the
electrical connector B and reattach the bulb
holding clip A;
❒ refit the protective cover B fig. 139. DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒
rotate the protective cover C fig. 139
anticlockwise;
❒ remove the bulb B fig. 143 and replace it;
❒ refit the protective cover A.
fig. 142
F0Q0707
fig. 143
F0Q0708
179GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Side
To change the bulb, proceed as follows:
❒adjust the lens A fig. 144 to compress in the
internal catch B, then pull the cluster outwards;
❒ turn the bulb holder C anticlockwise, extract the
press-fitted bulb D and replace it;
❒ refit the bulb holder C in the lens and turn it
clockwise;
❒ refit the cluster making sure that the internal catch
B clips into position. FOG LIGHTS
For replacing the bulb fig. 145 contact a Fiat
Dealership.
fig. 144
F0Q0709
fig. 145
F0Q0710
180GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REAR LIGHT CLUSTERS
The rear light clusters contain side lights, direction
indicators and brake lights (stop) bulbs.
The bulbs are arranged inside the light cluster as
follows fig. 146:BSide lights/brake light (double light)C
Direction indicators
To change the bulb, proceed as follows:
❒ open the luggage compartment and loosen the
two rear light cluster fastening screws A fig. 147;
❒ extract the light cluster by removing it with both
hands in the direction indicated by the arrows
fig. 148;
❒ disconnect the electrical connector and, adjusting
the three retaining tabs, remove the protective
cover A fig. 149. Then, replace the concerned bulb.fig. 146
F0Q0714
fig. 147
F0Q0715
fig. 148
F0Q0739
181GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REVERSE LIGHT
For bulb replacement fig. 150, contact a Fiat
Dealership.REAR FOG LIGHT
For bulb replacement fig. 151, contact a Fiat
Dealership.
3
rd
BRAKE LIGHTS
To change the bulb proceed as follows:
❒ open the luggage compartment;
❒ remove the cover A fig. 152;
❒ extract the lens unit B fig. 153 and disconnect the
electrical connector;
❒ press in the tabs C fig. 153 and remove the bulb
holder;
❒ remove the snap-fitted bulb and replace it.
❒ refit the cover A fig. 152 and close the luggage
compartment.
fig. 149
F0Q0713
fig. 150
F0Q0711
fig. 151
F0Q0712
182GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICING AND MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX