deactivate FIAT BRAVO 2015 2.G Owners Manual

THE FIAT CODE SYSTEMTo further protect your car from theft, it has been
fitted with an engine immobilising system. It is
automatically activated when the ignition key is
removed.
There is an electronic device in each key which can
identify the signal emitted, when the engine is
started, from an aerial built into the ignition switch.
The signal is the "password", different every time the
vehicle is started, through which the control unit
recognises the key and enables starting.
OPERATION
Each time the vehicle is started turning the ignition
key to MAR-ON, the Fiat CODE system control unit
sends an acknowledgement code to the engine
control unit to deactivate the immobiliser. The code
is sent only if the Fiat CODE system control unit
has acknowledged the code received from the key.
Each time the ignition key is turned to STOP, the Fiat
CODE system deactivates the functions of the
engine management control unit.
If, during starting, the code is not correctly
recognised, the
warning light (or symbol on the
display) switches on in the instrument panel.
In this case, turn the key to STOP and then to
MAR-ON; if it is still locked, try again with the other
keys that come with the vehicle. Contact a Fiat
Dealership if you still cannot start the engine. IMPORTANT Each key has its own code which must
be stored by the system’s control unit. To have
new keys stored, up to a maximum number of eight
keys, contact a Fiat Dealership and be ready to
present all the keys you have in your possession, the
CODE card, a personal identity document and the
car ownership documents. The codes for keys not
presented during the storing procedure will be
deleted to ensure that any keys that are lost or
stolen cannot be used to start the engine.
warning light (or symbol on the display)
on whilst driving
❒ If the
warning light (or symbol in the display)
switches on, this means that the system is running
self-diagnosis (caused, for example, by a voltage
drop).
❒ If thewarning light (or symbol in the display)
stays on, contact a Fiat dealership.
The electronic components inside the key
may be damaged if the key is subjected
to strong shocks.
7GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

IMPORTANT Setting is possible between 30 and 200
km/h, or 20 and 125 mph, according to the
previously set unit. See the "Units of measurement
adjustment (Units of measurement)" paragraph
described below. The setting will increase/decrease
by 5 units each time button
/
is pressed. Hold
down the
/
button to automatically increase/
decrease the setting rapidly. Complete the
adjustment with single presses of the button when
you approach the desired value.
Briefly press the MODE button to return to the
menu screen or hold the button down to return to
the standard screen without storing.
To cancel the setting, proceed as follows:
❒ briefly press button MODE, (On) will flash on the
display;
❒ press button, (Off ) will flash on the display;
❒ press the MODE button briefly to return to the
menu screen or hold the button down to return
to the standard screen without storing.
Headlight sensor (Automatic headlight/dusk
sensor sensitivity adjustment)
(for versions/markets, where provided)
This function is used to turn the headlights on or off
according to external lighting conditions.
The headlight sensor sensitivity can be adjusted
according to 3 levels (level 1 = minimum sensitivity,
level2=av erage sensitivity, level 3 = maximum
sensitivity). The higher the sensitivity set, the lesser
is the external light variation needed to switch the lights on (e.g. with a setting on level 3 at sunset
the headlights come on in advance in relation to
levels 1 and 2).
Proceed as follows to set the desired adjustment:
❒
briefly press the MODE button: the previously set
level flashes on the display;
❒ press
or
to make your choice;
❒ press the MODE button briefly to return to the
menu screen or hold the button down to return
to the standard screen without storing.
Cornering lights (Activation/deactivation of
“Cornering lights”)
(fog light with cornering function)
(for versions/markets where provided)
This function activates/deactivates the cornering
lights.
To activate/deactivate (On/Off ) the lights, proceed as
follows:
❒ press the MODE button briefly, the display will
show “On” or “Off ” flashing depending on the
previous setting;
❒ press
or
to make your choice;
❒ briefly press the MODE button to return to the
menu screen or hold the button down to return
to the standard screen without storing.
21GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Activation/Trip B data (Activating Trip B)
This function can be used to activate (On) or
deactivate (Off ) the Trip B display (partial trip). For
further information see “Trip computer” in this
section.
Proceed as follows to switch the function on/off:
❒briefly press the MODE button: On or Off flashes
on the display (according to the previous setting);
❒ press
or
to make your choice;
❒ briefly press the MODE button to return to the
menu screen or hold the button down to return
to the standard screen without storing.
Time adjustment (Clock adjustment)
This function enables to set the clock through two
submenus: “Time” and “Format”.
To carry out the adjustment, proceed as follows:
❒ briefly press the MODE button and two
submenus, "Time" and "Format", are displayed;
❒ press theor
button to switch between the
two submenus;
❒ once you have selected the submenu to be
changed, press the MODE button briefly;
❒ when you select “Time”, briefly pressing the
MODE button makes the hours flash on the
display;
❒ press the
or
button to make the adjustment; ❒
briefly press the MODE button: “minutes” starts
flashing on the display;
❒ press the button
or
for setting.
IMPORTANT The setting will increase or decrease
by one unit each time the button
or
is pressed.
Hold down the button to increase/decrease the
setting rapidly and automatically. Complete the
adjustment with single presses of the button when
you approach the desired value.
If you enter the "Format" submenu, pressing the
MODE button briefly makes the display format flash
on the display;
❒ Press button
or
to select “24h” or “12h”.
❒ when you have made the adjustment, briefly press
the MODE button to go back to the submenu
screen or hold the button down to go back to the
main menu screen without storing.
❒ hold down the MODE button again to return to
the standard screen or to the main menu
according to where you are in the menu.
When you have made the adjustment, briefly press
the MODE button to go back to the submenu screen
or hold the button down to go back to the main
menu screen without storing.
22GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

See radio (Audio information display)
With this function the display shows information
about the sound system.
❒Radio: selected radio station frequency or RDS
message, automatic tuning activation or
AutoSTore;
❒ Audio CD, MP3 CDs: track number;
❒ CD Changer: CD number and track number;
To show the radio information on the display (On)
or clear it (Off ), proceed as follows:
❒ briefly press the MODE button, the display will
show "On" or "Off" flashing depending on the
previous setting;
❒ press
or
to make your choice;
❒ briefly press the MODE button to return to the
menu screen or hold the button down to return
to the standard screen without storing.
Autoclose (Automatic central locking with
the car in motion)
When activated (On), this function locks the doors
automatically when the vehicle speed exceeds 20
km/h.
Proceed as follows to activate or deactivate this
function:
❒ briefly press the MODE button to display a
submenu; ❒
briefly press the MODE button: "On" or "Off"
flashes on the display according to the previous
setting;
❒ press
or
to make your choice;
❒ press the MODE button briefly to return to the
submenu screen or hold the button down to
return to the main menu screen without storing;
❒ hold down the MODE button again to return to
the standard screen or to the main menu
according to where you are in the menu.
Unit of measurement (Setting the unit of
measurement)
With this function it is possible to set the units
through three submenus: "Distances",
"Consumption" and "Temperature". To set the
desired unit, proceed as follows:
❒ briefly press the MODE button to display the
three submenus;
❒ press buttonor
to navigate through the three
submenus;
❒ once you have selected the submenu to be
changed, press the MODE button briefly;
❒ when you select the “Distances” submenu, briefly
pressing the MODE button makes the display
show “km” or “mi” depending on the previous
setting;
24GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Button volume (adjusting the button volume) This function allows the volume of the acoustic signal that accompanies MODE,
and
button
presses to 8 levels To set the desired volume, proceed as follows:❒
press the MODE button briefly, making the display flash the previously set volume "level";
❒
press the
or
button to make the adjustment;
❒
press the MODE button briefly to return to themenu screen or hold the button down to returnto the standard screen without storing.
Seat belt buzzer (Buzzer activation for SBRindication) This function can be displayed only after a Fiat Dealership has deactivated the SBR system (see the“Safety” section in the “SBR system” paragraph). To reactivate this function, proceed as follows:❒
briefly press the MODE button, the display shows "Off" flashing. Press the
or
button and "On"
will appear;
❒
briefly press the MODE button to return to thesubmenu screen or hold the button down toreturn to the main menu screen without storing.
Service (Scheduled servicing)
26GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND MESSAGESIN AN EMERGENCYSERVICING ANDMAINTENANCETECHNICAL
SPECIFICATIONS
INDEX
This function allows you to display the information about km/mileage intervals or, for versions/markets,where provided, time intervals for car servicing. To consult this information, proceed as follows:
❒
briefly press the MODE button: the display shows when servicing is due in km/mi or days (whereprovided) or mi or days (where provided)according to the previous setting (see paragraph"Units of measurement");
❒
briefly press the MODE button to go back to the menu screen or hold the button down to go backto the standard screen.
Note
The “Scheduled Servicing Plan” includes car
maintenance at fixed intervals (refer to the"Maintenance and care" chapter). This is displayedautomatically, with ignition key at MAR-ON, 2000km (or equivalent value in miles) before servicing or,where provided, 30 days before servicing. It is alsodisplayed each time the key is turned to MAR-ON or,for versions/markets, where provided, every 200 km(or equivalent value in miles). Below this thresholdservicing indications are more frequent. The displaywill be in km or miles according to the unit ofmeasurement set. When the following scheduledservicing is approaching, the word “Service” willappear on the display, followed by the number ofkilometres/miles or days (where provided) left, whenthe key is turned to MAR-ON. Go to a FiatDealership, where the "Scheduled Servicing Plan"operations will be performed and the message willbe reset. When the service interval is reached and for about 1000 km/600 mi or 30 days, a service due message isdisplayed.

Airbag/Passenger bag This function is used to activate/deactivate the passenger side airbag. Proceed as follows:❒
press the MODE button and, after the message "Bag pass: Off" (to deactivate) or "Bag pass: On"(to activate) is displayed by pressing the
and
buttons, press the MODE button again;
❒
a confirmation request message will appear on thedisplay;
❒
by pressing the
or
buttons, select ("Yes") (to
confirm activation/deactivation) or ("No") (tocancel);
❒
press the MODE button briefly and a messageconfirming the selection will be displayed, then youwill return to the menu screen, or hold thebutton down to return to the standard screenwithout storing.
Exit menu The last function closing the cycle of settings listed in the menu screen. Press the MODE button briefly to return to the standard screen without storing. Press the
button to go back to the first menu
option ("Speed Beep").
27GETTING TO KNOW YOUR CAR SAFETYSTARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCYSERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS INDEX

A
air temperature adjustment knob (hot/cold air
mixing)
Bheated rear window on/off buttonC
fan activation knob
D
internal air recirculation on/off button
Eair distribution knob.
PASSENGER COMPARTMENT HEATING
Proceed as follows:
❒ turn knob A to the red section;
❒ turn knob C to the required speed;
❒ turn knob E to:
to warm the feet and demist the windscreen at
the same timeto warm the feet and keep the face cool (bi-level
function)to warm the feet of those in the front and rear
seats
❒ to turn off internal air recirculation (LED on
button
off ).
FAST FRONT WINDOW DEMISTING/
DEFROSTING
Proceed as follows:
❒ turn knob A fully to the right;
❒ turn knob C to
; ❒
turn knob E to
;
❒ turn off internal air recirculation (LED on button
off ).
After demisting/defrosting, operate the controls to
maintain optimum visibility conditions.
Window demisting
In the event of considerable external moisture
and/or rain and/or large differences in temperature
inside and outside the passenger compartment,
perform the following preventive window demisting
procedure:
❒ to turn off internal air recirculation (LED on
button
off );
❒ turn knob A to the red section;
❒ turn knob C to the second speed level;
❒ turn knob E to
or to
if there is no sign of
the windows steaming up.
HEATED REAR WINDOW AND DOOR
MIRRORS DEMISTING/DEFROSTING
Press button
to activate this function; when this
function is activated, the button LED
lights up.
This function is timed and will deactivate
automatically after 20 minutes. Press the button
again to switch the function off in advance.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid
damage.
40GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

HEATED REAR WINDOW AND DOOR
MIRRORS DEMISTING/DEFROSTING
Press button
to activate this function: when this
function is activated, the button LED
lights up.
This function is timed and will deactivate
automatically after 20 minutes. Press the button
again to switch the function off in advance.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid
damage.
FAN SPEED ADJUSTMENT
To ventilate the passenger compartment properly,
proceed as follows:
❒ fully open the central and side air diffusers;
❒ turn knob A to the blue section;
❒ turn knob C to the required speed;
❒ turn knob E to
;
❒ turn off internal air recirculation (LED on button
off ).
INTERNAL AIR RECIRCULATION
ACTIVATION
Press button
: when the function is on, the
button LED lights up. It is advisable to switch the internal air recirculation
on while standing in queues or in tunnels to prevent
the introduction of polluted air. However, it is better
not to use the function for long periods, particularly
if there are many people on board, to prevent the
windows from misting.
IMPORTANT Internal air recirculation makes it
possible to reach the required heating or cooling
conditions more quickly depending on the mode
selected. It is not advisable to switch the internal air
recirculation on when it is rainy/cold or the windows
might steam up, especially if the climate control
system is not turned on.
CLIMATE CONTROL SYSTEM (cooling)
Proceed as follows:
❒
turn knob A to the blue section;
❒ turn knob C to the required speed;
❒ turn knob F to
;
❒ press
and
buttons (button LEDs on).
Cooling adjustment
Proceed as follows:
❒ deactivate thebutton (LED on button off );
❒ turn knob A rightwards to increase the
temperature;
❒ turn knob C leftwards to reduce the fan speed.
44GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

During automatic operation it is still possible to
adjust the temperatures set and carry out the
following operations manually:
❒fan speed adjustment;
❒ air distribution selection;
❒ internal air recirculation and AQS function
activation/deactivation;
❒ climate control system compressor activation.
WARNING
It is advisable not to use the internal air
recirculation function when the outside
temperature is low, because the windows could
mist rapidly.
FAN SPEED ADJUSTMENT
Press button
to increase/decrease the fan speed.
The 12 possible speeds are indicated by bars lighting
up on the display:
❒ maximum fan speed = all bars lit
❒ minimum fan speed = one bar lit.
The fan can be disabled (no bars lit) only if the
climate control system compressor has been
switched off by pressing button
.
To restore automatic fan speed control after a
manual adjustment, press the AUTO button. RAPID FRONT WINDOW
DEMISTING/DEFROSTING
(MAX-DEF function)
Press button to automatically activate the timed
operation of all the functions required to rapidly
demist/defrost the windscreen and front side
windows.
The functions are:
❒
climate control system compressor activation
(with an outside temperature of above 4°C);
❒ switching off, if previously on, of the internal air
recirculation (LED on button
off );
❒ activation of heated rear window (LED on button
on) and door mirror heater coils;
❒ setting maximum air temperature;
❒ activation of air flow.
HEATED REAR WINDOW AND DOOR
MIRRORS DEMISTING/DEFROSTING
Press button
to activate: when this function is
activated, the button LED switches on.
This function is timed and will deactivate
automatically after 20 minutes. Press the button
again to switch the function off in advance.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid
damage.
48GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

SET TEMPERATURE ALIGNMENT (MONO function) Press the MONO button to align the temperature between the driver side and passenger side. Then turn the AUTO or MONO knob to increase/decrease the temperature between the twoareas by the same amount. Press MONO again to deactivate the function. CLIMATE CONTROL SYSTEM COMPRESSOR ACTIVATION/DEACTIVATION Press the
button to switch on the climate control
system compressor. Compressor engagement ❒
button LED
on;
❒
symbol appears on display.
Compressor deactivation❒
button LED
off;
❒
symbol on display disappears;
❒
internal air recirculation excluded;
❒
AQSfunctiondisabled
With the climate control system compressor switched off, air cannot be introduced into thepassenger compartment that has a lowertemperature than the outside air; in this case the
symbol in the display will flash.
The deactivation of the climate control systemcompressor is memorised even after the engine hasstopped. To reactivate the climate control systemcompressor, press the
or AUTO button again:
if you press AUTO, the other manual settings will becancelled. IMPORTANT In order to preserve the battery charge, the electronic climate control managementpermits a higher ventilation speed than minimumonly if the engine is running at a speed greater than750 rpm. When the speed drops below thisthreshold – possible when setting off, for example –the ventilation speed is automatically reduced tominimum. AIR DISTRIBUTION SELECTION Press one or more of these buttons
/
/
to
manually select one of the seven possible air distribution settings for the passenger compartment:
Air flow to the windscreen and front sidewindow diffusers to demist/defrost them.Air flow to the front and rear footwell diffusers.This air distribution allows the passengercompartment to be warmed up quickly.
Air flow distribution between front andrear diffusers, centre/side dashboarddiffusers, rear diffuser and windscreen andfront side window demisting/defrostingdiffusers.
Air flow distribution to centre/side dashboarddiffusers (passenger's body).
50GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND MESSAGESIN AN EMERGENCYSERVICING ANDMAINTENANCETECHNICAL
SPECIFICATIONS
INDEX
(forversions/markets,whereprovided).