engine oil FIAT BRAVO 2015 2.G Owners Manual

Electric devices
Use electrical devices only for the amount of time
necessary. The heated rear window, additional
headlights, windscreen/rear window wipers and
heater fan need a considerable amount of energy,
therefore increasing fuel consumption (by up to 25%
in the urban cycle).
Climate control system
Air conditioning leads to higher fuel consumption (on
average up to +20%). If the temperature outside
permits, try and use the air vents.
Spoilers
The use of non-certified spoilers may adversely affect
air drag and fuel consumption.DRIVING STYLE
The main driving styles that affect fuel consumption
are listed below.
Starting
Do not warm the engine with the car at a standstill
or at idle or high speed: under these conditions
the engine warms up much more slowly, increasing
electrical consumption and emissions. It is therefore
advisable to move off immediately, slowly, avoiding
high speeds: in this way the engine will warm faster.
Unnecessary actions
Avoid accelerating when starting at traffic lights or
before switching off the engine. This and also double
declutching is absolutely pointless on modern cars
and also increases consumption and pollution.
Gear selection
As soon as the conditions of the traffic and road
allow, use a higher gear. Using a low gear for faster
acceleration will increase consumption.
In the same way improper use of a high gear
increases consumption, emissions an engine wear.
Max. speed
Fuel consumption increases considerably with speed.
Maintain a constant speed, avoiding unnecessary
braking and acceleration, which cost in terms of both
fuel consumption and emissions.
140GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

PASSENGER/SIDE AIRBAGS
DEACTIVATED (amber)
The warning light
switches on when the front
passenger's airbag and side bag are disabled. With
front passenger airbag on, when the ignition key
is turned to MAR-ON, the
warning light switches
on constantly for several seconds, it flashes for
another few seconds and then it should switch off.
WARNING
A failure of the
warning light is
indicated by warning light
switching
on. In addition, the airbag system automatically
disables the airbags on the passenger's side
(both front and side airbags where provided).
Before continuing, contact a Fiat Dealership
immediately to have the system checked.
UNFASTENED SEAT BELTS (red)
The warning light switches on constantly with the
car stationary and the driver's side or passenger side
seat belt (when the passenger is present) not
fastened. The warning light will flash and a buzzer will sound if
the car is in motion and the front seat belts are
not correctly fastened.
The SBR (Seat Belt Reminder) system buzzer can
only be permanently switched off by a Fiat
Dealership.
The system can be reactivated using the Setup Menu.
LOW BATTERY CHARGE (red)
The warning light comes on when the ignition key is
turned to MAR-ON, but it should go out as soon
as the engine has started (with the engine running at
idle speed a brief delay before going out is
acceptable).
If the warning light stays on constantly or continues
to flash, contact a Fiat Dealership immediately.CONTINUOUSLY ON: LOW
ENGINE OIL PRESSURE (red)
ON FLASHING: ENGINE OIL
DETERIORATED
(only MultiJet versions with DPF - red)
When the ignition key is turned to MAR-ON, the
warning light switches on but should switch off
as soon as the engine is started.
148GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Low engine oil pressure
The warning light switches on constantly together
(for versions/markets, where provided) with a
message on the display when the system detects that
the engine oil pressure is too low.
WARNING
If the warning light
turns on when
the car is travelling (on certain versions
together with the message on the display) stop
the engine immediately and contact a Fiat
Dealership.
Engine oil degraded
(versions with DPF only)
The warning light will flash and a specific message will
appear on the display (for versions/markets, where
provided). The warning light may flash in the
following ways, depending on the version:
❒ for 1 minute every two hours;
❒ cycles of 3 minutes with intervals with the warning
light off for 5 seconds until the oil is changed.
After the first indication, at each engine start-up the
warning light will continue flashing as described
above until the oil is changed. The display (for
versions/markets, where provided), shows a
dedicated message together with the warning light. The flashing of this warning light should not be
considered as a fault; it informs the customer that
the oil needs to be changed following normal car use.
Note that engine oil degrades faster under the
following circumstances:
❒
mainly town use of the car which makes the DPF
regeneration process more frequent;
❒ use of the car for short drives, in which the engine
does not have time to reach its regular operating
temperature;
❒ repeated interruption of the regeneration process,
signalled by the DPF warning light coming on.
WARNING
If the warning light switches on, the
deteriorated engine oil must be changed
as soon as possible, and never more than 500
km from the first time that the warning light
switches on. Failure to observe the above
indication may result in severe damage to the
engine and invalidate the warranty. Remember
that the operation of this warning light is not
related to the amount of oil in the engine.
Therefore, never top up with oil when the
warning light starts flashing.
149GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

INCOMPLETE DOOR LOCKING
(red)
The warning light switches on when one or more
doors are not completely shut. An acoustic signal is
activated with the doors open and the car moving.GENERIC FAILURE INDICATION
(amber)
Fuel cut-off inertia switch tripped
The warning light comes on when the inertial fuel
cut-off switch is triggered. The display shows the
dedicated message.
Engine oil pressure sensor failure
The warning light comes on when the engine oil
pressure sensor is faulty.
Dusk sensor failure
This warning light comes on when a dusk sensor
fault is detected. The display shows the dedicated
message.
Preset speed limit exceeded
(for Arab countries only)
The warning light switches on when the vehicle
speed exceeds 120 km/h. Rain sensor failure
The warning light switches on when a rain sensor
fault is detected. The display shows the dedicated
message.
Parking sensor failure
(for versions/markets, where provided)
The warning light turns on when failure is detected in
the parking sensors.
Tyre pressure monitoring system failure
(for versions/markets, where provided)
The warning light turns on when a failure is detected
in the TPMS (for versions/markets where provided).
Should one or more wheels without a sensor be
fitted, the instrument panel warning light will come
on and stay on until the initial conditions are
restored. The display shows the dedicated message.
Note
If one of the above mentioned failures occurs,
contact a Fiat Dealership as soon as possible.
151GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

DPF (DIESEL PARTICULATE
FILTER) CLEANING IN PROGRESS
(only versions with DPF) (amber)
When the key is turned to MAR-ON, the warning
light switches on but should switch off after a few
seconds. The warning light (together with a message
and a symbol on the display on some versions)
switches on constantly to notify the driver that the
DPF system needs to eliminate captured pollutants
(particulate) through the regeneration process.
The warning light does not switch on during every
DPF regeneration, but only when driving conditions
require that the driver is notified. To switch the
warning light off, the car must be kept moving until
the regeneration process is completed.
On average, the process lasts fifteen minutes. The
best conditions to complete the regeneration
process are reached driving the car at about 60 km/h
with engine speed over 2000 rpm.
If this light switches on, it does not mean that the
car is defective, so there is no need to take it to
a workshop. On some versions, together with the
warning light switching on, the display shows a
dedicated message.
WARNING
The driving speed must always be
suitable for traffic and weather
conditions and the driver must always comply
with the Highway Code.The engine may be
switched off even if the DPF warning light is on:
repeated interruptions of the regeneration
process could cause an early deterioration of
engine oil. For this reason it is always advisable
to wait for the light to go off before turning
off the engine, following the instructions above.
It is not a good idea to complete DPF
regeneration with the car stationary.
152GETTING TO KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

FUSE SUMMARY TABLEDashboard fuse boxFUSEAMPS
Right dipped headlight (halogen headlights) F127,5
Right dipped headlight (Bi-Xenon headlights) F1215
Left dipped headlight (halogen headlights) F137,5
Left dipped headlight (Bi-Xenon headlights) F1315
Reverse F355
3rd brake light F377,5
Rear fog light (driver's side) F537,5
Headlight alignment corrector system
(halogen headlights) F13
7,5
Relay switch coils on engine compartment fuse box
(CVM)/Body Computer control unit (NBC) F31
5
HI-FI audio system subwoofer amplifier F3215
Left rear electric window F3320
Right rear electric window F3420
Control on brake pedal (NC contact)/Water presence
in diesel sensor/Air flow meter F35
5
Central locking system control unit (CGP)
(door opening/closing, safe lock, tailgate release) F36
20
Control on brake pedal (normally open contact NO)/
Instrument panel (NQS)/Gas discharge bulbs control
units on front headlights F37
7,5
193GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

SCHEDULED SERVICING PLAN
203GETTING TO KNOW YOUR CAR SAFETYSTARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCYSERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS INDEX
Thousandsofmiles
12
2
3
60
72
84
96
108
120
Thousands of km 20 40 60 80 100 120 140 160 180 200Years
12345678910
Check tyre condition/wear and adjust pressure, if necessary; check “Fix&Go Automatic” kit rechargeexpiry date (for versions/markets, where provided)
●●●●●●●●●●
Check operation of lighting system (headlights, direction indicators, hazard warning lights, luggagecompartment, passenger compartment, glovecompartment, instrument panel warning lights, etc.)
●●●●●●●●●●
Check and, if necessary, top up fluid levels (engine coolant, hydraulic clutch/brakes, windscreen washer,battery, etc.)
●●●●●●●●●●
Check exhaust emissions/smokiness
●●●●●●●●●●
Use the diagnosis socket to check supply/engine management system operation, emissions and, forversions/markets, where provided, engine oildegradation
●●●●●●●●●●
Visually inspect condition of: exterior bodywork, underbody protection, pipes and hoses (exhaust,fuel system, brakes), rubber elements (boots,sleeves, bushes, etc.)
●●●●●
Check windscreen/rear window wiper blade position/wear
●●●●●
Check operation of windscreen wiper/washer system and adjust jets, if necessary
●●●●●
4
648
The checks listed in the Scheduled Servicing Plan, after reaching 120,000 km/6 years, must be cyclically repeated starting from the first interval, thus following the same intervals as before.

204GETTING TO KNOW
YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND MESSAGESIN AN EMERGENCYSERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Thousandsofmiles
12
2
3
6
7
8
9
1
12
Thousands of km 20 40 60 80 100 120 140 160 180 200Years
12345678910
Check cleanliness of bonnet and luggage compartment locks, as well as cleanliness andlubrication of linkages
●●●●●
Check handbrake lever travel and adjust, if required
●●●●●
Visually inspect conditions and wear of front disc brake pads and operation of pad wear indicator
●●●●●●●●●●
Visual inspection of condition and wear of rear disc brake pads
●●●●●●●●●●
Visual inspection of condition and tensioning of accessory drive belt(s) (for versions withoutautomatic tensioner only)
●●
Change engine oil and replace the oil filter (versions without DPF)
●●●●●
Change engine oil and replace oil filter (versions with DPF)
(1) (2)
(2) If the car is mainly used in towns and cities, change the engine oil and filter every year.
4
6
48
0
2
4
6
08
0
(1) The actual interval for changing engine oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled
by the warning light or message in the instrument panel. Anyway, it must never exceed 2 years.

205GETTING TO KNOWYOUR CAR SAFETYSTARTING AND DRIVING WARNING LIGHTS AND MESSAGES IN AN EMERGENCYSERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS INDEX
PERIODIC CHECKSEvery 1,000 km or before long journeys, check and, if necessary, restore: ❒
engine coolant, brake fluid and windscreen washer fluid level;
❒
tyre inflation pressure and condition;
❒
operation of lighting system (headlamps, directionindicators, hazard warning lights, etc.);
❒
operation of screen washer/wiper system andpositioning/wear of windscreen/rear window wiperblades.
Every 3,000 km, check and top up, if required, theengine oil level.
Thousands of miles 12 25 37 50 62 75 87 99 112 124 Thousands of km 20 40 60 80 100 120 140 160 180 200Years
12345678910
Replace accessory drive belt(s)
(3)
●
Replace toothed timing drive belt
(3)
●
Replace fuel filter
(4)
●●●
Replace air cleaner cartridge
(5)
●●●●●
Replace brake fluid
●●●●●
Passenger compartment filter replacement
(5)
O
●
O
●
O
●
O
●
O
●
(3) Areas that are not dusty: advised maximum mileage 120,000 km. Regardless of the mileage, the belt must be replaced every 6
years. Dusty areas and/or demanding use of the car (cold climates, town use, long periods of idling): advised maximum mileage 60,000 km. Regardless of the mileage, the belt must be replaced every 4 years.
(4) If the car runs on fuel with quality below the relevant European specification, this filter must be replaced every 20,000 km(5) If the car is used in dusty areas, this cleaner must be replaced every 20,000 km.(O) Recommended operations( ●) Mandatory operations

CHECKING FLUID LEVELS
WARNING
Never smoke while working in the engine compartment : inflammable gases
and vapours may be present , constituting a firerisk.
WARNING
Be very careful when working in theengine compartment when the engine is
hot : you may get burned. Remember that thefan may start up if the engine is hot : this couldinjure you. Make sure that scarves, ties andother loose fitting garments do not get caughtup in moving parts.
When topping up, take care not to mix upthe various types of fluids: they are notcompatible with each other and could
seriously damage the car.
206GETTING TO KNOW
YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND MESSAGESIN AN EMERGENCYSERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
HEAVY-DUTY USE OF THE CARIf the car is used mainly under one of the followingconditions: ❒
towing a trailer or caravan;
❒
dusty roads;
❒
short, repeated journeys (less than 7-8 km) at sub-zero outside temperatures;
❒
engine often idling or driving long distances at lowspeeds or long periods of idleness;
you need to perform the following inspections morefrequently than shown in the Scheduled ServicingPlan: ❒
check front disc brake pad conditions and wear;
❒
check cleanliness of bonnet and boot locks, cleanliness and lubrication of linkage;
❒
visually inspect conditions of: engine, gearbox,transmission, pipes and hoses (exhaust - fuelsystem - brakes) and rubber elements (boots -sleeves - bushes - etc.);
❒
check battery charge and battery fluid level(electrolyte);
❒
visually inspect condition of the accessory drivebelts;
❒
check and, if necessary, change engine oil andreplace oil filter;
❒
check and, if necessary, replace pollen filter.