Hand brake FIAT DOBLO 2008 1.G User Guide

108DRIVING YOUR VEHICLE
IMPORTANTAfter a taxing drive
you should allow the engine to “catch
its breath” before turning it off by let-
ting it idle to allow the temperature in
the engine compartment to fall.
PARKING
Switch off the engine, pull up the
handbrake and engage a gear (1st gear
or reverse, according to whether the
vehicle is facing up or downhill) and
leave the wheels turned. If the vehi-
cle is left on a steep slope, wedges or
a rock should be used to lock the
wheels.
Do not leave the ignition key at
MARto prevent draining the battery.
Always remove the key when you
leave the vehicle.HANDBRAKE
The handbrake lever is located be-
tween the two front seats.
Pull the handbrake lever upwards un-
til the vehicle cannot be moved. Four
or five clicks are generally enough
when the vehicle is on level ground
while nine or ten may be required if
the vehicle is on a steep slope or laden.
IMPORTANTIf this is not the
case, take the vehicle to a Fiat Deal-
ership to have the handbrake adjust-
ed.
Instrument panel warning light x
will come on when the handbrake
lever is pulled up and the ignition key
is at MAR.
To release the handbrake:
1)Slightly lift the handbrake and
press release button A-fig.1.
2)Keep the button pressed in and
lower the lever. Warning light xwill
go out.
3)Press the brake pedal when car-
rying out this operation to prevent the
vehicle moving accidentally. STOPPING THE ENGINE
Turn the key to STOPwhile the
engine is idling.
A quick burst on the ac-
celerator before turning
off the engine serves ab-
solutely no practical purpose and
wastes fuel.
Never leave children un-
supervised in the vehicle.
A
fig. 1
F0A0034b
106-118 Doblo GB 9-05-2008 12:09 Pagina 108

118DRIVING YOUR VEHICLE
The following precautions should be
taken if the vehicle will not be used for
several months:
– Park the vehicle in covered, dry and
if possible well-ventilated premises.
– Engage a gear.
– Make sure the handbrake is not en-
gaged.
– Remove the cables from the bat-
tery terminals (first remove the cable
to the negative terminal), and check
the battery charge. If the vehicle is to
be stored for long periods the charge
of the battery should be checked
every month and recharged if it falls
below 12.5V.IMPORTANT Where relevant,
switch off the electronic alarm with the
remote control.
– Clean and protect the painted parts
using protective wax.
– Clean and protect the shiny metal
parts using special compounds readi-
ly available.
– Sprinkle talcum powder on the
rubber windscreen and rear window
wiper blades and lift them off the glass.
– Slightly open the windows.– Cover the vehicle with a cloth or
perforated plastic sheet. Do not use
sheets of non-perforated plastic as
they do not allow moisture on the ve-
hicle body to evaporate.
– Inflate the tyres to 0.5 bar above
the normal specified pressure and
check it at intervals.
– Do not drain the engine cooling
system.
VEHICLE STORAGE
106-118 Doblo GB 9-05-2008 12:09 Pagina 118

122IN AN EMERGENCY
To change a wheel proceed as
follows:
1)Stop the vehicle in a position that
is not dangerous for oncoming traffic
where you can change the wheel safe-
ly. The ground should be flat and ad-
equately firm. Do not lubricate the bolt
threads before fitting
them back: they could
come loose.
Fasten the wheel cap correctly
to prevent the wheel from com-
ing free in motion.
Never tamper with the inflation
valve.
Never place tools between the
rim and tyre.
Check the tyre and spare wheel
pressure regularly. The tyre in-
flation pressure is shown in sec-
tion “Technical specifications”.
CHANGING A WHEEL
Please note:
– The jack weighs 1.85 kg
– The jack requires no adjustments
– The jack cannot be repaired. If it
breaks it must be replaced with a new
jack
– No tool with the exception of the
handle can be fitted on the jack.2)Turn the engine off and pull up the
handbrake.
3Engage first or reverse gear.
4)Either move the left-hand front
seat back forwards (Fiat Doblò Car-
go versions) lifting lever A-fig. 2and
take the tool bag shown in fig. 3or lift
the rear seat (for Fiat Doblò Passen-
ger Transport versions) with lever B-
fig. 4and take the bag shown in fig.
5. Take the bag to the wheel to be re-
placed.
5)Take the wheel removal wrench.
A
fig. 2
F0A0040b
fig. 3
F0A0094b
119-148 Doblo GB 9-05-2008 12:09 Pagina 122

Put on the protection
gloves provided together
with quick tyre repair kit.
– Pull up the handbrake. Loosen
tyre inflation valve cap, take out the
filler hose A-fig. 16cand screw the
ring nut B-fig. 16con the tyre valve; The compressor shall
not be operated for more
than 20 minutes. Risk of
overheating!. Tyres repaired with
the quick tyre repair kit shall be
used temporarily only.
127IN AN EMERGENCY
Repairs are not possible
in case of damages on the
wheel rim (bad groove
distortion causing air loss). Do
not remove foreign bodies
(screws or nails) from the tyre.
IT SHOULD BE NOTICED
THAT:
The sealing fluid of the quick tyre re-
pair kit is effective with external tem-
peratures between -20 °C and +50
°C.
The sealing fluid has limited life. The cylinder contains
ethylene glycol. The cylin-
der contains latex: it can
cause allergic reactions. It is
harmful if ingested or inhaled and
irritant for the eyes and in case of
contact. In case of contact rinse
immediately with water and take
off contaminated clothes. If swal-
lowed, do not induce vomit, rinse
out the mouth, drink a lot of wa-
ter and call the doctor immedi-
ately. Keep away from children.
This product must not be used by
asthmatics. Do not inhale
vapours. Call the doctor imme-
diately in case of allergic reac-
tions. Keep the cylinder in the
space provided for the purpose
and far from heat. The sealing flu-
id has limited life.Replace the cylinder if
sealer has run out. Do not
throw away the cylinder
and the sealing fluid. Have the
sealing fluid and the cylinder dis-
posed of in compliance with na-
tional and local regulations.
INFLATING PROCEDURE
119-148 Doblo GB 9-05-2008 12:09 Pagina 127

If the pressure falls be-
low 1.8 bars, do not dri-
ve any further: the quick
tyre repair kit Fix & Go auto-
matic cannot guarantee proper
hold because the tyre is too
much damaged. Contact Fiat
Dealership.
– if at least 1.8 bar pressure is read,
restore proper pressure (with engine
running and handbrake on) and
restart;
– drive with the utmost care to the
nearest Fiat Dealership.
129IN AN EMERGENCY
– after driving for about 10 minutes
stop and check again the tyre pres-
sure; pull up the handbrake;It is of vital importance
to communicate that the
tyre has been repaired us-
ing the quick tyre repair kit. Hand
the instruction brochure to the
personnel charged with treating
the tyre repaired with the kit.
FOR CHECKING AND
RESTORING PRESSURE
ONLY
The compressor can be also used
just for restoring pressure. Disconnect
the quick connection and connect it
directly to the tyre valve; in this way
the cylinder is not connected to com-
pressor and the sealing fluid will not
flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as
follows fig. 16h:
– disconnect connectionA; turn
counter-clockwise the cylinder to re-
place and raise it; fit the new cylinder
and turn it clockwise; connect con-
nection Ato the cylinder and fit the
transparent tube Binto the proper
space.
fig. 16g
F0A0716b
fig. 16h
F0A0542b
119-148 Doblo GB 9-05-2008 12:09 Pagina 129

136IN AN EMERGENCY
THIRD BRAKE LIGHTS
To replace a bulb, open either the
left-hand door or the tailgate and
loosen the screws A-fig. 31.
Remove the lens from its housing
from the outside.
Remove the clipped-on bulb B-fig.
32and replace it.NUMBER PLATE LIGHT
To replace a bulb, press the tab in
the point shown in fig. 33and remove
the cluster. Turn the bulb holder A-
fig. 34anticlockwise and remove bulb
B. IF AN INTERIOR
LIGHT BURNS OUT
fig. 31
F0A0528b
B
fig. 32
F0A0144b
fig. 33
F0A0527b
fig. 34
F0A0529b
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
See “If a bulb burns out” in this chap-
ter for bulb type and power.
119-148 Doblo GB 9-05-2008 12:09 Pagina 136

141IN AN EMERGENCY
FUSE SUMMARY TABLE
10
10
10
10
10
10
15
10
7.5
15
10
10
10
7.5
10
7.5
10
20
7.5
40
70
40
20
20
20
20
15
7.5
7.5 F14
F15
F12
F13
F42
F53
F30
F53
F51
F32
F42
F37
F53
F31
F37
F51
F37
F44
F50
F02 – MAXI FUSE
F01 – MAXI FUSE
F04 – MAXI FUSE
F48
F47
F38
F22
F11
F42
F18 42
42
41
41
41
41
42
41
41
41
41
41
41
41
41
41
41
41
41
42
42
42
41
41
41
42
42
41
42
Figure Fuse Ampere
Right-hand main beam
Left-hand main beam
Right-hand dipped beam
Left-hand dipped beam
Boot
Hazard lights
Front fog lights
Direction indicators
Dashboard instrument lights
Light system
Ceiling light
Instrument panel and warning lights (ignition switch powered)
Instrument panel and warning lights (battery powered)
Reversing light
Brake lights
Number plate light
Additional brake light (third stop light)
Cigar lighter
Air bag
Dashboard control unit power: optional functions
Dashboard control unit power: standard functions
ABS power (pump)
Right front power window
Left front power window
Door locking system
Ignition coils
Engine control system secondary loads
ABS control unit (ignition switch powered)
Engine control unit (+battery)
119-148 Doblo GB 9-05-2008 12:09 Pagina 141

150VEHICLE MAINTENANCE
thousands of kilometres
Check tyre conditions / wear and adjust pressure, if required
Check lighting system operation (headlights, direction indicators,
hazard lights, boot light, passenger's compartment lights,
glove compartment light, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation, adjust nozzles
Check windscreen/rear window wiper blade position/wear
Check front disk brake pad conditions and wear
Check rear drum brake lining conditions and wear
Inspect conditions of: underbody protection, piping (exhaust -
fuel feed and brakes), rubber parts (boots, sleeves, bushings, etc.),
fuel feed and braking system hosing
Check cleanness of locks, bonnet and boot and lever
cleanness and lubrication
Sight inspect accessory drive belt conditions
Replace accessory drive belts
Check/adjust tappet clearance (1.4 8V and 1.9 Multijet versions)
Check and adjust handbrake lever stroke
Check exhaust gas/smokiness (diesel versions)
Check anti-evaporation system
Replace fuel filter (Multijet versions)
SERVICE SCHEDULE
The scheduled service must be carried out every 20,000 km.
20 40 60 80 100 120 140 160 180
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●
●●●●●●●●●
●●●●●●●●●
●●
●
●●●
●●●●
●●●●
●●
●●●
149-173 Doblo GB 9-05-2008 12:10 Pagina 150

182TECHNICAL SPECIFICATIONS
TRANSMISSION
CLUTCH
Hydraulic, self-adjusting external
control.
GEARBOX
Five forward gears and reverse with
synchromesh for front gear engage-
ment.
Cyclical gear reduction and differen-
tial assembly incorporated in the gear-
box.
Drive transmission to the front
wheels by means of drive shafts con-
nected to the differential assembly and
the wheels with CV joints.
BRAKES
SERVICE AND
EMERGENCY BRAKES
Front:
– disc, floating shoe, self-ventilated.
Rear:
– drum, self-centring callipers.
Crossed hydraulic circuit control.
Vacuum brake booster.
ABS system with four sensors and
EBD.
Automatic take-up of friction liner
wear.
Lacking the ABS, there is the brake
force distributor that acts on rear
brake circuit according to load on rear
axle
HANDBRAKE
Controlled by a lever, it works me-
chanically on the rear brake shoes.
SUSPENSIONS
FRONT
Independent wheel, McPherson sus-
pension with steel wishbones an-
chored to an auxiliary crossmember.
Coil springs and sway bar.
Double acting telescopic hydraulic
shock absorbers.
REAR
Stiff axle with wishbones.
Double acting telescopic hydraulic
shock absorbers.
Sway bar in Fiat Doblò Passengers
Transport versions.
174-211 Doblo GB 16-12-2008 14:26 Pagina 182

213INDEX
- rear window ............................. 61
- windscreen ............................... 60
Digital clock .......................... 26-27
Dimensions ................................... 187
Direction indicators
- control ...................................... 64
- front bulb replacement .......... 133
- rear bulb replacement ........... 134
- side bulb replacement ............ 134
Door lock/unlock
remote control ............................. 8
Double ladder (partitions) ......... 51
Driver’s protection ladder
(partitions)................................... 51
Driving your vehicle .................... 106
EBD electronic brake force
distributor ................................... 90
Electric windows .......................... 74
Electronic brake force
distributor EBD .......................... 90
Electronic control units .............. 166
Engine
- fuel feed ..................................... 181
- identification code .................. 176
- ignition ...................................... 181
- specifications ............................ 179Engine compartment
- washing ...................................... 172
Engine coolant gauge ................... 25
Engine coolant level ..................... 159
Engine oil
- checking the level.................... 157
- consumption............................. 158
- specifications ............................ 202
Engine oil level .............................. 157
EOBD system................................ 97
Evaporation system...................... 104
Exhaust gas recirculation ............ 104
Extending the boot ...................... 80
Fiat CODE system ..................... 6
First aid kit ..................................... 148
Follow me home ......................... 66
Front doors ................................... 74
Front foglights
- bulb replacement ................... 133
- control button ......................... 68
Fuel
- at the filling station ................. 102
- capacities .................................. 200
- fuel cut-off switch ................... 69
- gauge .......................................... 25
Fuel cap........................................... 103Fuel consumption ......................... 204
Fuel cut-off switch........................ 69
Fuses
- dashboard fusebox.................. 139
- engine compartment
fusebox ...................................... 140
- replacement.............................. 138
- table............................................ 141
Gearbox
- gearbox use .............................. 109
- technical characteristics ........ 182
Getting to know your vehicle ... 6
Glove compartment .................... 69
Handbrake .......................... 107-182
Hazard lights.................................. 68
Headlight beam corrector.......... 88
Headlight slant
(electrical corrector) ................ 88
Headlights
- adjusting the headlights
abroad........................................ 89
- beam corrector ....................... 88
- beam direction......................... 89
- slant compensation ................. 88
Head restraints
212-220 Doblo GB 16-12-2008 14:26 Pagina 213