brake FIAT DOBLO 2008 1.G Owner's Manual

Put on the protection
gloves provided together
with quick tyre repair kit.
– Pull up the handbrake. Loosen
tyre inflation valve cap, take out the
filler hose A-fig. 16cand screw the
ring nut B-fig. 16con the tyre valve; The compressor shall
not be operated for more
than 20 minutes. Risk of
overheating!. Tyres repaired with
the quick tyre repair kit shall be
used temporarily only.
127IN AN EMERGENCY
Repairs are not possible
in case of damages on the
wheel rim (bad groove
distortion causing air loss). Do
not remove foreign bodies
(screws or nails) from the tyre.
IT SHOULD BE NOTICED
THAT:
The sealing fluid of the quick tyre re-
pair kit is effective with external tem-
peratures between -20 °C and +50
°C.
The sealing fluid has limited life. The cylinder contains
ethylene glycol. The cylin-
der contains latex: it can
cause allergic reactions. It is
harmful if ingested or inhaled and
irritant for the eyes and in case of
contact. In case of contact rinse
immediately with water and take
off contaminated clothes. If swal-
lowed, do not induce vomit, rinse
out the mouth, drink a lot of wa-
ter and call the doctor immedi-
ately. Keep away from children.
This product must not be used by
asthmatics. Do not inhale
vapours. Call the doctor imme-
diately in case of allergic reac-
tions. Keep the cylinder in the
space provided for the purpose
and far from heat. The sealing flu-
id has limited life.Replace the cylinder if
sealer has run out. Do not
throw away the cylinder
and the sealing fluid. Have the
sealing fluid and the cylinder dis-
posed of in compliance with na-
tional and local regulations.
INFLATING PROCEDURE
119-148 Doblo GB 9-05-2008 12:09 Pagina 127

If the pressure falls be-
low 1.8 bars, do not dri-
ve any further: the quick
tyre repair kit Fix & Go auto-
matic cannot guarantee proper
hold because the tyre is too
much damaged. Contact Fiat
Dealership.
– if at least 1.8 bar pressure is read,
restore proper pressure (with engine
running and handbrake on) and
restart;
– drive with the utmost care to the
nearest Fiat Dealership.
129IN AN EMERGENCY
– after driving for about 10 minutes
stop and check again the tyre pres-
sure; pull up the handbrake;It is of vital importance
to communicate that the
tyre has been repaired us-
ing the quick tyre repair kit. Hand
the instruction brochure to the
personnel charged with treating
the tyre repaired with the kit.
FOR CHECKING AND
RESTORING PRESSURE
ONLY
The compressor can be also used
just for restoring pressure. Disconnect
the quick connection and connect it
directly to the tyre valve; in this way
the cylinder is not connected to com-
pressor and the sealing fluid will not
flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as
follows fig. 16h:
– disconnect connectionA; turn
counter-clockwise the cylinder to re-
place and raise it; fit the new cylinder
and turn it clockwise; connect con-
nection Ato the cylinder and fit the
transparent tube Binto the proper
space.
fig. 16g
F0A0716b
fig. 16h
F0A0542b
119-148 Doblo GB 9-05-2008 12:09 Pagina 129

131IN AN EMERGENCY
TYPES OF BULBS
Several types of bulbs are installed in
the vehicle fig. 17:
A Glass bulbs
Clipped into position.
To remove them, pull.B Bayonet connection bulbs
Remove from the bulb holder by
pressing the bulb and turning it
anticlockwise.
C Cylindrical bulbs
Remove by pulling away from
terminals.D-E Halogen bulbs
To remove the bulb, release
the clip holding the bulb in
place.
A
B
C
E
D
fig. 17
F0A098b
Fig. 17
E
D
A
B
A
E
B
B
B
B
B
A
C
APower
55W
55W
5W
21W
5W
55W
21/5W
21W
21W
21W
21W
5W
10W
10W
5W Type
H1
H7
W5W
PY21W
W5W
H1
P21W/5W
P21W
PY21W
P21W
P21W
W5W
C10W
W5WBulb
Main beam headlights
Dipped beam headlights
Front sidelights
Front direction indicators
Side direction indicators
Front fog lights
Taillights and brake lights
Third brake light
(supplementary brake lights)
Rear direction indicators
Reversing light
Rear fog light
Number plate light
Ceiling light:
– with toggle lens
– with map reading light
Boot
119-148 Doblo GB 9-05-2008 12:09 Pagina 131

135IN AN EMERGENCY
2)Fit the wrench provided A-fig. 28
(used also to remove the wheel) to
the fastening bolt of the light unit.
3)Loosen the bolts, then undo the
light cluster fastening nuts by means of
extension B-fig. 28supplied with the
unit.
As regards the 7-seater version is
concerned, undo the light cluster fas-
tening bolt by means of extension B-
fig. 28 inserted onto the bolt through
slotted hole C-fig. 28a.
4)Undo, after removing the fasten-
ing bolt, the cluster fastening screws
(located outside), as illustrated in
fig. 29.5)Take out the pressure-fit con-
nector.
6)Undo the four fastening screws to
remove the bulb holder and get access
to the bulbs.
7)Remove the bulbs fig. 30by push-
ing them gently and turning them
counterclockwise (bayonet fitting)
A– brake light bulb
B– indicator light bulb
C– reversing light bulb
D– sidelight bulb
E– rear fog light bulb
fig. 28a
F0A0406b
fig. 29
F0A0525b
fig. 30
F0A0526b
fig. 28
F0A0401b
119-148 Doblo GB 9-05-2008 12:09 Pagina 135

136IN AN EMERGENCY
THIRD BRAKE LIGHTS
To replace a bulb, open either the
left-hand door or the tailgate and
loosen the screws A-fig. 31.
Remove the lens from its housing
from the outside.
Remove the clipped-on bulb B-fig.
32and replace it.NUMBER PLATE LIGHT
To replace a bulb, press the tab in
the point shown in fig. 33and remove
the cluster. Turn the bulb holder A-
fig. 34anticlockwise and remove bulb
B. IF AN INTERIOR
LIGHT BURNS OUT
fig. 31
F0A0528b
B
fig. 32
F0A0144b
fig. 33
F0A0527b
fig. 34
F0A0529b
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
See “If a bulb burns out” in this chap-
ter for bulb type and power.
119-148 Doblo GB 9-05-2008 12:09 Pagina 136

141IN AN EMERGENCY
FUSE SUMMARY TABLE
10
10
10
10
10
10
15
10
7.5
15
10
10
10
7.5
10
7.5
10
20
7.5
40
70
40
20
20
20
20
15
7.5
7.5 F14
F15
F12
F13
F42
F53
F30
F53
F51
F32
F42
F37
F53
F31
F37
F51
F37
F44
F50
F02 – MAXI FUSE
F01 – MAXI FUSE
F04 – MAXI FUSE
F48
F47
F38
F22
F11
F42
F18 42
42
41
41
41
41
42
41
41
41
41
41
41
41
41
41
41
41
41
42
42
42
41
41
41
42
42
41
42
Figure Fuse Ampere
Right-hand main beam
Left-hand main beam
Right-hand dipped beam
Left-hand dipped beam
Boot
Hazard lights
Front fog lights
Direction indicators
Dashboard instrument lights
Light system
Ceiling light
Instrument panel and warning lights (ignition switch powered)
Instrument panel and warning lights (battery powered)
Reversing light
Brake lights
Number plate light
Additional brake light (third stop light)
Cigar lighter
Air bag
Dashboard control unit power: optional functions
Dashboard control unit power: standard functions
ABS power (pump)
Right front power window
Left front power window
Door locking system
Ignition coils
Engine control system secondary loads
ABS control unit (ignition switch powered)
Engine control unit (+battery)
119-148 Doblo GB 9-05-2008 12:09 Pagina 141

147IN AN EMERGENCY
IF AN ACCIDENT
OCCURS
– It is important to keep calm.
– If you are not directly involved in
the accident, stop at least ten metres
away from the accident.
– If you are on a motorway, do not
obstruct the emergency lane with
your vehicle.
– Turn off the engine and turn on the
hazard lights.
– At night, illuminate the scene of the
accident with your headlights.
– Act carefully, you must not risk be-
ing run over.
– Mark the accident by putting the
red triangle at the regulatory distance
from the vehicle where it can be clear-
ly seen.
– Call for rescue making the infor-
mation you give as accurate as you
can. On the motorway use the special
column-mounted emergency phones. When towing the vehi-
cle, you must comply with
the specific traffic regula-
tions regarding the tow hitch and
how to tow on the road.
Before starting to tow,
turn the ignition key to
MAR and then to STOP.
Do not remove the key. If the key
is removed, the steering lock en-
gages automatically which pre-
vents the wheels being turned.
While the vehicle is be-
ing towed with the engine
off, remember that the
brake pedal and steering will re-
quire more effort as you no
longer have the benefit of the
power brakes and power steer-
ing. Do not use flexible cables to
tow. Avoid jerking. Whilst tow-
ing, ensure that the coupling to
the vehicle does not damage the
surrounding components.
fig. 47
F0A0417b
B-fig. 47- Rear ring for towing an-
other vehicle.
119-148 Doblo GB 9-05-2008 12:09 Pagina 147

150VEHICLE MAINTENANCE
thousands of kilometres
Check tyre conditions / wear and adjust pressure, if required
Check lighting system operation (headlights, direction indicators,
hazard lights, boot light, passenger's compartment lights,
glove compartment light, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation, adjust nozzles
Check windscreen/rear window wiper blade position/wear
Check front disk brake pad conditions and wear
Check rear drum brake lining conditions and wear
Inspect conditions of: underbody protection, piping (exhaust -
fuel feed and brakes), rubber parts (boots, sleeves, bushings, etc.),
fuel feed and braking system hosing
Check cleanness of locks, bonnet and boot and lever
cleanness and lubrication
Sight inspect accessory drive belt conditions
Replace accessory drive belts
Check/adjust tappet clearance (1.4 8V and 1.9 Multijet versions)
Check and adjust handbrake lever stroke
Check exhaust gas/smokiness (diesel versions)
Check anti-evaporation system
Replace fuel filter (Multijet versions)
SERVICE SCHEDULE
The scheduled service must be carried out every 20,000 km.
20 40 60 80 100 120 140 160 180
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●
●●●●●●●●●
●●●●●●●●●
●●
●
●●●
●●●●
●●●●
●●
●●●
149-173 Doblo GB 9-05-2008 12:10 Pagina 150

151VEHICLE MAINTENANCE
20 40 60 80 100 120 140 160 180
●●●●
●●●
●●●●●●●●●
●●
●
●●●●
●●●●
●●
●●●●●●●●●
(●)(●)(●)(●)(●)(●)(●)(●)(●)
●●●
●●●●●●●●●thousands of kilometres
Replace air cleaner cartridge (petrol versions)
Replace air cleaner cartridge (Multijet versions)
Top up fluids (engine coolant, brakes, windscreen washer, battery, etc.)
Check timing belt conditions (excluding 1.3 Multijet versions)
Replace timing belt (excluding 1.3 Multijet versions) (*)
Replace spark plugs (petrol versions)
Check engine control systems (via diagnostic socket)
Check mechanical transmission oil level
Change engine oil and oil filter (versions without DPF) (O)
Change engine oil and oil filter (Multijet versions with DPF)
(or every 2 years) (**)
Change brake fluid (or every 2 years)
Change pollen filter (or every 2 years)
(*) Or every 4 years for very demanding use (cold climate, idling in city traffic, dusty areas).
Or every 5 years, regardless from the distance travelled.
(
O) Every 30.000 km or 2 years for Multijet versions
(**)Engine oil and oil filter shall be changed according to their actual exhaust conditions, indicated by warning light/message (where provided) on the
instrument panel (see section “Warning lights and messages”).
149-173 Doblo GB 9-05-2008 12:10 Pagina 151

152VEHICLE MAINTENANCE
ANNUAL
INSPECTION
SCHEDULE
For vehicles with an annual
mileage of below 20.000 km (for
example about 10.000 km) the
following yearly inspection pro-
gramme is advised:
– check tyre conditions/wear and ad-
just pressure if required (including the
spare wheel).
– check light system operation (head-
lights, direction indicators, hazard
lights, boot lights, passenger compart-
ment lights, glovebox light, warning
lights, etc.).
– check windscreen wiper/washer
operation, adjust nozzles.
– check windscreen/rear window
blade position/wear
– check front disk brake pad condi-
tions and wear.– check cleanness of bonnet and
boot locks and lever cleanness and lu-
brication
– sight inspect the conditions of: en-
gine, gearbox, transmission, pipes and
hoses (exhaust - fuel - brakes), rubber
parts (boots, sleeves, bushes, etc)
brake and fuel hoses.
– check battery charge.
– visual check on various drive belt
conditions.
– check and top up, if required, fluid
levels (engine coolant, brake fluid,
windscreen washer fluid, battery fluid,
etc.).
– change engine oil.
– change engine oil filter.
– replace pollen filter (where pro-
vided).
ADDITIONAL
CHECKS
Every 1,000 kmor before long
trips, check and top up as necessary:
engine coolant level, brake fluid level,
windscreen washer liquid level, tyre
pressure and conditions.
Every 3,000 km check and top up
as necessary: engine oil level.
You are recommended to use FL
Selenia,products designed and pro-
duced specifically for Fiat vehicles (see
“Capacities” in section “Technical
specifications”).
149-173 Doblo GB 9-05-2008 12:10 Pagina 152