Sound system FIAT DOBLO 2008 1.G Owners Manual

20GETTING TO KNOW YOUR VEHICLE
Never remove the igni-
tion key while the vehicle
is moving. The steering
wheel would automatically lock
as soon as you try to turn it. This
also applies when the vehicle is
being towed.
It is absolutely forbidden
to carry out whatever af-
ter-market operation in-
volving steering system or steer-
ing column modifications (e.g.: in-
stallation of anti-theft device)
that could badly affect perfor-
mance and safety, cause the lapse
of warranty and also result in
non-compliance of the vehicle
with homologation require-
ments.
IGNITION DEVICE
The key can be turned to 4 different
positions fig. 26:
– STOP:engine off, key can be re-
moved, steering column locked. Some
electrical devices can be worked (e.g.
sound system, electric window
winders).
– MAR: drive position. All electrical
devices can be used.
– AVV: engine ignition.
– PARK:engine off, parking lights
on, steering column locked. Press but-
ton Aand turn the key to PARK.
A
fig. 26
F0A0018b
If the ignition device is
tampered with (e.g.: at-
tempted theft), have it
checked over by a Fiat Dealership
as soon as possible.
When you get out of the
vehicle, always remove
the ignition key. This will
prevent anyone from accidental-
ly working the controls. Remem-
ber to apply the handbrake and,
if the vehicle is faced down on a
steep slope engage the first gear.
If it is facing up, engage the re-
verse gear. Never leave unsuper-
vised children in the vehicle.
STEERING COLUMN LOCK
To engage the lock: remove the
ignition key at STOPor PARKand
turn the steering wheel until it locks.
To release the lock: rock the
steering wheel slightly as you turn the
ignition key to MAR.
001-105 Doblo GB 16-12-2008 14:22 Pagina 20

42GETTING TO KNOW YOUR VEHICLE
EOBD engine control system
failure
Under normal conditions, turning the
ignition key to MAR, the warning light
turns on, but it should go out as soon
as the engine is started. The initial
turning on indicates that the warning
light is working properly. If the warn-
ing light stays on or turns on when
travelling:
– glowing steadily: means a fault in
the supply/ignition system which could
cause high emissions at the exhaust,
possible lack of performance, poor
handling and high consumption levels.
On certain versions the dedicated
message is displayed.
In these conditions it is possible to
continue driving without however re-
quiring heavy effort or high speed from
the engine. Prolonged use of the ve-
hicle with the warning light on may
cause damages. Contact Fiat Deal-
ershipas soon as possible. The warn-
ing light goes off if the fault disappears,
but it is still stored by the system.
– flashing: indicates the possibility
of damage to the catalyst (see “EOBD
system” in this section). INJECTION SYSTEM
FAILURE
(Multijet versions -
amber)
EOBD SYSTEM FAILURE
(petrol versions - amber)
Injection system failure
Turning the ignition key to MAR the
warning light turns on but it should go
off after engine starting.
If the warning light stays on or turns
on when travelling, means a fault in the
supply/ignition system which could
cause high emissions at the exhaust,
possible lack of performance, poor
handling and high consumption levels.
On certain versions the dedicated
message is displayed.
In these conditions it is possible to
continue driving without however re-
quiring heavy effort or high speed from
the engine. In any case, contact Fiat
Dealershipas soon as possible. INCOMPLETE
DOOR LOCKING
(red)
On certain versions the warning
light turns on when one or more
doors or the tailgate are not proper-
ly shut.
On certain versions the dedicated
message is displayed; symbols
¯/ ˙
indicate respectively left / right door
open.
A buzzer will sound when doors/tail-
gate are open and the vehicle is mov-
ing (only for versions with reconfig-
urable multifunction display).
´U
001-105 Doblo GB 16-12-2008 14:22 Pagina 42

97GETTING TO KNOW YOUR VEHICLE
EOBD SYSTEM
The EOBD system (European On
Board Diagnosis) allows continuos di-
agnosis of the components of the ve-
hicle correlated with emissions.
Furthermore, the system warns the
driver of deterioration concerning the
emission system components by
means of the Uwarning light on the
instrument panel.
The objective is to:
– monitor system efficiency;
– warn when failures can increase
emissions over the threshold estab-
lished by the European regulations;
– warn of the need to replace dete-
riorated components.
Furthermore, the system is equipped
with a connector for interfacing with
specific tools used to read the error
codes stored in the control unit mem-
ory along with a set of diagnostic and
engine specific parameters.IMPORTANTAfter eliminating the
problem, your Fiat Dealershipwill
run a bench test to fully check the sys-
tem. In some cases, a long road test
may be required. Contact a Fiat Dealer-
ship as soon as possible if
the Uwarning light ei-
ther does not come on when the
key is turned to MAR or comes
on, with fixed or flashing light,
when travelling. Warning light U
operation can be checked by
means of special equipment by
traffic agents. Always comply
with the traffic regulations in
force in the country where you
are travelling.
SOUND SYSTEM
If the “Sound System” has not been
requested, the vehicle features an odd-
ment compartment on the dashboard.
If you wish to have a radio
installed, after purchasing
the vehicle, first go to a Fiat
Dealership who will be able to
advise on the subject in order to
safeguard the life of the battery and
protect the vehicle electrical sys-
tem. Excessive absorption will drain
and damage the battery and may
invalidate the battery warranty. The
lack of protection provided with a
factory-fitted radio may adversely
affect the correct operation of the
vehicle diagnostic system.
LIGHT PRESETTING
The system consists of the following:
– sound system power wires;
– wires for front speakers on the
dashboard, doors (where provided)
and rear speakers for passengers
transport versions;
– sound system compartment;
– aerial wire and aerial.
001-105 Doblo GB 16-12-2008 14:22 Pagina 97

98GETTING TO KNOW YOUR VEHICLE
43 21
10987 65
fig. 146
F0A0099b
fig. 145
F0A0096B
CELLULAR PHONE
SET-UP
The system set-up consists of:
– a dual-purpose aerial (sound sys-
tem + cellular phone), on the vehicle
roof;
– a dual-purpose aerial connection
wires and ten-pin connector wiring
fig. 146.
– a double coil speaker (sound sys-
tem + cellular telephone), located on
the passenger side dashboard. HEAVY PRESETTING
The system consists of the following:
– sound system power wires;
– wires for front speakers on the
dashboard;
– 2 speakers on the dashboard;
– wires for door speakers (where
provided);
– 2 door speakers;
– 2 rear speakers (for passengers
transport versions);
– wires for rear speakers;
– sound system compartment;
– aerial wire and aerial.Speakers
– two mid-range speakers on dash-
board, diameter 100 mm, power 30W
max each.
– two woofer speakers on front
doors, diameter 165 mm, power 40W
max each (Panorama versions only).
– two full-range elliptic speakers on
rear window shelf, 95 x 154 mm, pow-
er 20W max each (Panorama versions
only).
Sound system installation
To fit the sound system, remove the
oddment compartment shown in fig.
145. To remove the compartment,
press it upwards and then pull it out
towards the inside of the vehicle.
fig. 144
F0A0162B
001-105 Doblo GB 16-12-2008 14:22 Pagina 98

99GETTING TO KNOW YOUR VEHICLE
Wiring diagram:
1Sound system mute function.
2Spare.
3Cellular phone input earth signal.
4Cellular phone INPUT signal.
5Dual-purpose speaker on the front
passenger side door (+).
6Dual-purpose speaker on the front
passenger side door (-).
7Ignition switch power (+15).
8Spare.
9Battery power (+).
10Earth.Maximum power to be
applied to the aerial is
20W.
Have the cellular tele-
phone installed and con-
nected to the setup sys-
tem in the vehicle by a Fiat Deal-
ership only. This will ensure the
best results and prevent any
problems which could effect ve-
hicle safety.
Purchase a free-hands kit
which is compatible for
your cellular telephone.
fig. 147
F0A0210b
fig. 148
F0A0211b
Have the cellular telephone and the
connections performed by a Fiat
Dealershiponly.
In Fiat Doblò passengers Transport
versions, use a screwdriver in the
point shown in fig. 147to reach the
ten pin connector. Lift the central tun-
nel cover and remove the connector.
In Fiat Doblò Cargo versions, loosen
the screws shown in fig. 148in the
glove compartment to reach the ten
pin connector. Use a screwdriver in
the pre-cut point and remove the con-
nector.
001-105 Doblo GB 16-12-2008 14:22 Pagina 99

142IN AN EMERGENCY
Engine control unit (power)
Engine control unit (ignition switch powered)
Glow plug control unit
Horn
Manual climate control enable control
Ignition switch
Manual climate control compressor
Headlight beam adjuster
Petrol fume recirculation solenoid valve
Tachometer generator
Injectors
Heated rear window
One-speed radiator fan
Fuel pump
Fuel pump
Windscreen-rear window washer pump
Supplementary power socket
ABS power (valve)
Radiator fan first speed
(versions with manual climate control system)
Radiator fan first speed (1.3 -1.9 Multijet versions)
Radiator fan second speed
(1.4 - 1.6 versions with manual climate control system)
Radiator fan second speed (1.3 -1.9 Multijet versions)
Heated seats
+ 30 services
(sound system, cellular telephone, diagnostic socket)
Figure Fuse Ampere
10
7.5
15
15
7.5
20
7.5
10
15
15
20
30
30
20
15
30
20
30
30
40
60
40
15
10 F17
F16
F11
F10
F31
F03 – MAXI FUSE
F19
F13
F11
F11
F22
F40
F06 – MAXI FUSE
F22
F21
F43
F44
F05 – MAXI FUSE
F06 – MAXI FUSE
F06 – MAXI FUSE
F07 – MAXI FUSE
F07 – MAXI FUSE
F45
F39 42
42
42
42
41
42
42
41
42
42
42
41
42
42
42
41
41
42
42
42
42
42
41
41
119-148 Doblo GB 9-05-2008 12:09 Pagina 142

143IN AN EMERGENCY
+15 services (sound system, cellular telephone,
dashboard control lighting, electrical mirrors,
trailer, heated seat control lighting)
Lambda sensors (oxygen sensors)
Heated rearview mirrors
Engine cooling system relay
Engine control system relay
Pump system relay
Fan system relay
passenger compartment heater
Safet belt buzzer muting relay
Windscreen wiper
Rear window wiper
Passenger compartment fan
Subwoofer system
Spare
Spare
Spare
Spare
Spare
Spare
Figure Fuse Ampere
7.5
15
7.5
7.5
7.5
7.5
7.5
7.5
30
15
30
15
–
–
–
–
–
– F49
F11
F41
F18
F16
F31
F31
F49
F43
F52
F08
F36
F35
F09
F33
F34
F46
F23 41
42
41
42
42
41
41
41
41
41
42
41
41
42
41
41
41
42
119-148 Doblo GB 9-05-2008 12:09 Pagina 143

When working on the
battery or near it, always
wear the
USEFUL ADVICE FOR
LENGTHENING THE LIFE OF
YOUR BATTERY
To avoid draining your battery and
lengthen its life, observe the follow-
ing indications:
– when you park the vehicle, ensure
the doors, tailgate and bonnet are
closed properly;If the vehicle is left inac-
tive for long periods at
cold, remove the battery
and store it in a warm place to
prevent freezing.
165VEHICLE MAINTENANCE
IMPORTANTA battery which is
kept at a charge of less than 50% for
any length of time will be damaged by
sulphation leading to a reduction in
cranking power and a higher risk of
the battery electrolyte freezing (this
may even occur at –10°C).
If the vehicle is inactive for a long pe-
riod of time, refer to the “Vehicle
storage” paragraph in section “Driving
your vehicle”.
If you want to add accessories after
buying the vehicle (alarm system, free-
hand phone kit, etc.) visit a Fiat Deal-
ership. They can suggest the most suit-
able accessories to get and check
whether the electric system can sup-
port the required load or whether a
larger capacity battery is required.
These devices will, in fact, run off the
battery even when the key is not in-
serted (vehicle parked) and can deploy
the battery. – the ceiling lights must be off. The
vehicle is however provided with an
automatic system for switching off in-
ternal lights;
– do not keep accessories (e.g. sound
system, hazard lights, etc.) switched on
for a long time when the engine is not
running;
– before performing any operation
on the electrical system, disconnect
the battery negative cable;
– battery terminals shall always be
perfectly tightened.
149-173 Doblo GB 9-05-2008 12:10 Pagina 165

166VEHICLE MAINTENANCE
ELECTRONIC
CONTROL UNITS
When the vehicle is being used nor-
mally, special measures are not neces-
sary.
The following instructions must be
followed very carefully, however, if
you work on the electrical system or
in cases where emergency starting is
necessary:
– Never disconnect the battery from
the electrical system while the engine
is running.
– Disconnect the battery from the
electrical system if you are recharg-
ing it. The modern battery chargers
can discharge voltage up to 20V.
– Never perform emergency start-
ups with a battery charger. Always use
an auxiliary battery.
– Be particularly careful when con-
necting the battery to the electrical
system. Ensure the battery posts are
connected up to the right leads (the Battery Maximum
admitted
stand-by intake
40 Ah 24 mA
50 Ah 30 mA
60 Ah 36 mApolarity is correct) and check that the
connection has been made properly.
– Do not connect or disconnect the
terminals of the electronic units while
the ignition key is at MAR.
– Do not check polarity through
sparking.
– Disconnect the electronic units if
you are electrically welding the vehi-
cle body. Remove the units if temper-
atures exceed 80°C (special opera-
tions on the bodywork, etc.).
IMPORTANTIf the sound system
or alarm systems are not installed cor-
rectly, they can interfere with the
working of the electronic control
units.
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
The total intake of these systems
(factory and after-market) must be less
than 0.6 mA x Ah (of the battery) as
shown in the following table:
149-173 Doblo GB 9-05-2008 12:10 Pagina 166

Modifications or repairs
to the fuel system that
are not carried out prop-
erly or do not take the system
technical specifications into ac-
count can cause malfunctions
leading to the risk of fire. FUEL SUPPLY/IGNITION
Petrol versions
Electronic Multipoint sequential
phased injection integrated with igni-
tion, returnless system.FUEL FEED/IGNITION
Multijet versions
“Common Rail” electronic control
direct injection, turbo and intercool-
er.
SPARK PLUGS
The cleanness and soundness of the
spark plugs are very important for
keeping the engine efficient and pol-
luting emissions down.
The appearance of the spark plug, if
examined by an expert eyes, is a good
way of pinpointing a problem even if it
has nothing to do with the ignition sys-
tem. Therefore, if the engine has prob-
lems, it is important to have the spark
plugs checked at a Fiat Dealership.
The spark plugs must be
changed at the times
specified in the service
schedule. Only use the type of
plugs indicated. If the heat ratio
is less than required or the life
specified is not guaranteed, prob-
lems can arise.
181TECHNICAL SPECIFICATIONS
174-211 Doblo GB 16-12-2008 14:26 Pagina 181