brake light FIAT IDEA 2007 1.G User Guide
[x] Cancel search | Manufacturer: FIAT, Model Year: 2007, Model line: IDEA, Model: FIAT IDEA 2007 1.GPages: 314, PDF Size: 4.78 MB
Page 140 of 314

139
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
EBD failure
It is signalled by lighting up of instrument panel
warning lights
>and xtogether with the message
(where provided) on the reconfigurable multifunction
display (see the “Warning lights” chapter).In this case with sharp braking the rear wheels might
lock too early, with the possibility of skidding. Drive
extremely carefully to the nearest Fiat Dealership to
have the system checked.
WARNINGIf brake fluid low warning light xlights up on the instrument panel (together, where
provided, with the message on the reconfigurable multifunction display), stop
immediately the car and contact the closest Fiat Dealership. Fluid leaks from the
hydraulic system, in fact, can compromise the braking system, both traditional
systems and systems with ABS.
When the ABS cuts in, and you feel the brake pedal pulsating, do not remove your
foot, but keep it pressed; in doing so you will stop in the shortest amount of space
possible under the current road conditions.WARNING
Page 144 of 314

ACCESSORIES PURCHASED BY
THE OWNER
If, after buying the car, you decide to install electrical
accessories that require a permanent electric supply
(alarm, satellite antitheft system, etc.) or accessories that
in any case burden the electric supply, contact Fiat
Dealership, whose qualified personnel, besides suggesting
the most suitable devices belonging to Lineaccessori Fiat,
will also evaluate the overall electric absorption,
checking whether the vehicle electric system is able to
withstand the load required, or whether it needs to be
integrated with a more powerful battery.
INSTALLATION OF ELECTRIC/
ELECTRONIC DEVICES
Electric/electronic devices installed after buying the car
or in aftermarket shall bear the and marking:
Fiat Auto S.p.A. authorizes the installation of
transceivers provided that installation is carried out at
a specialized shop, workmanlike performed and in
compliance with manufacturer's specifications.
IMPORTANT Installation of devices resulting in
modifications of car characteristics may cause driving
license seizing by traffic agents and also the lapse of
143
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNINGBe careful when mounting additional spoilers, alloy rims and non original wheel
caps: they may reduce the brake ventilation and efficiency during sharp and
repeated braking or sloping downhill. Also make sure that nothing (over-carpeting,
etc.) interferes with the pedal stroke.
the warranty as concerns defects due to the
abovementioned modification or traceable back to it
directly or indirectly.
Fiat Auto S.p.A. declines all responsibility for damages
caused by the installation of non-genuine accessories
or not recommended by Fiat Auto S.p.A. and installed
not in compliance with the specified requirements.
RADIO TRANSMITTERS AND CELLULAR
TELEPHONES
Radio transceiver equipment (e.g.: e-tacs mobile
phones, HAM radio systems and the like) shall not be
used inside the vehicle unless a separate aerial is
mounted on the roof.
IMPORTANT The use of similar devices inside the
passenger compartment (without separated aerial)
produces radio-frequency electromagnetic fields
which, amplified by the resonance effects inside the
passenger compartment, may cause electrical systems
equipping the vehicle to malfunction. This could
compromise safety in addition to constituting a
potential hazard for the passengers.
In addition, transmission and reception of these
devices may be affected by the shielding effect of the
vehicle body.
As concerns EC-approved mobile phones (GSM,
GPRS, UMTS), strictly comply with the instructions for
use provided by the mobile phone’s manufacturer.
Page 148 of 314

FAILURE WARNINGS
See the “Warning lights and messages” chapter.
OPERATION WITH TRAILER
The system is preset for deactivating automatically
when the trailer electric cable plug is fitted into the car
tow hook socket.
Sensors are reactivated when removing the trailer
cable plug.GENERAL WARNINGS
❒When parking, take the utmost care to obstacles
set above or under the sensors.
❒Objects set close to car rear part, under certain
circumstances are not detected and could
therefore cause damages to the car.
❒Indications sent by the sensor can be altered by
dirt, snow or ice deposited on the sensors or by
ultrasound systems (e.g.: truck pneumatic brakes or
pneumatic hammers) set nearby the car.
147
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
For proper operation, the parking sensors set on the bumpers shall be clean from mud, dirt, snow or
ice. When cleaning the sensors, take the utmost care to prevent their damaging; do not use therefore
dry or rough clothes. Sensors shall be washed with clean water and car detergent, if required. In wash-
ing stations, clean sensors quickly keeping the vapour jet/high pressure washing nozzles at 10 cm at least from
the sensors.
WARNINGParking manoeuvres however are always under the driver’s responsibility that shall
always check the absence of people, animals or objects in the manoeuvre space.
This system is just a help for the driver but he shall never reduce important during
dangerous manoeuvres even if performed at low speed.
Page 153 of 314

SEAT BELTS
USING THE FRONT AND
REAR SIDE SEAT BELTS
The belt should be worn keeping the chest straight and rested against the
seat back.
To fasten the belt, take hold the tongue (A) and insert it into the buckle
(B), until hearing the locking click.
At removal, if it jams, let it rewind for a short stretch, then pull it out
again without jerking.
To unfasten the seat belts, press button (C). Guide the seat belt with
your hand while it is rewinding, to prevent it from twisting.
Through the reel, the belt automatically adapts to the body of the
passenger wearing it, allowing freedom of movement.
When the car is parked on a steep slope the reel mechanism may block;
this is normal. The reel mechanism prevents the webbing coming out
when it is jerked or if the car brakes sharply, in a collision or when
cornering at high speed.
The rear seat is fitted with inertial seat belts with three anchor points
and reel.
Rear seat belts shall be worn as shown in diagram (D) (5-seat versions)
or as shown in diagram (E) (4-seat versions).
152
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
F0H0126m
WARNINGDo not press button (C) during travelling.
F0H0309m
F0H0348m
Page 179 of 314

ENGINE STARTING
The car is fitted with an electronic engine lock device.
If the engine fails to start, see paragraph “Fiat CODE
system” in section “Dashboard and controls”.
The engine may be noisier than usual during the first
seconds of operation, especially after it has not been
used for a while. This characteristic feature of the
hydraulic tappet system does not compromise
functionality or reliability. The system devised for the
Fiat Idea was designed to limit maintenance
interventions.STARTING PROCEDURE FOR PETROL
VERSIONS
Proceed as follows:
❒Ensure that the handbrake is up;
❒Put the gear lever into neutral;
❒Press the clutch pedal down to the floor without
touching the accelerator;
❒Turn the ignition key to AVV and let it go the
moment the engine starts.
If the engine does not start at the first attempt, return
the ignition key to STOP before repeating starting.
If, when the ignition key is on MAR, warning light
Y
remains lit together with warning light U, turn the
key to STOP and then back to MAR; if the warning
light remains on, try with the other keys provided with
the car.
178
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
We recommend that during the initial period you do not drive to full vehicle performance (e.g.:
excessive acceleration, long journeys at top speed, sharp braking, etc.).
When the engine is switched off never leave the ignition key in the MAR position to prevent
pointless current absorption from draining the battery.
WARNINGRunning the engine in confined areas is extremely dangerous. The engine consumes
oxygen and produces carbon monoxide which is a highly toxic and lethal gas.
Page 180 of 314

If you are still unable to start the engine, perform the
emergency start-up procedure (see “Emergency start-
up” in section “In an emergency”) and contact Fiat
Dealership.
IMPORTANT Never leave the ignition key at MAR
when the engine is off.
STARTING PROCEDURE FOR MULTIJET
VERSIONS
Proceed as follows:
❒Ensure that the handbrake is up;
❒Put the gear lever into neutral;
❒Turn the ignition key to MAR: the warning lights
m, Uand Ywill light up on the instrument
panel;
❒Wait for the warning lights
Yand m. The
hotter the engine is, the quicker this will happen;
❒Press the clutch pedal down to the floor without
touching the accelerator;❒Turn the ignition key to AVV as soon as warning
light
mgoes out. If you wait too long you will
lose the benefit of the work done by the glow
plugs. Release the key as soon as the engine starts.
IMPORTANT With cold engine, the accelerator pedal
shall be completely released while turning the ignition
key to AVV.
If the engine does not start at the first attempt, return
the ignition key to STOP before repeating starting.
If, when the ignition key is on MAR, warning light Y
remains lit, turn the key to STOP and then back to
MAR; if the warning light remains on, try with the
other keys provided with the car.
If you still cannot start the engine, contact Fiat
Dealership.
IMPORTANT Never leave the ignition key at MAR
when the engine is off.
179
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
The warning light mwill flash for 60 seconds at start-up or during prolonged cranking to signal a
fault in the glow plug heating system. You can use the car as usual if the engine starts but you should
contact a Fiat Dealership as soon as possible.
Page 181 of 314

HOW TO WARM UP THE ENGINE AFTER IT
HAS JUST STARTED (petrol and Multijet
versions)
Proceed as follows:
❒Drive off slowly, letting the engine turn at medium
revs. Do not accelerate abruptly;
❒Do not drive at full performance for the initial
kilometres. Wait until the coolant temperature
gauge starts moving.
EMERGENCY START-UP
If the instrument panel warning light
Ystays on with
fixed light, the emergency start-up can be performed
by using the CODE card code (see section “In an
emergency”).STOPPING THE ENGINE
Turn the ignition to STOP while the engine is idling.
IMPORTANT After a taxing drive, you should allow
the engine to “catch its breath” before turning it off by
letting it idle to allow the temperature in the engine
compartment to fall.
180
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
Never bump start the engine by pushing, towing or coasting downhill. This could cause fuel to flow
into the catalytic exhaust system and damage it beyond repair.
A quick burst on the accelerator before turning off the engine serves absolutely no practical
purpose, it wastes fuel and is damaging especially to turbocharged engines.
Remember that the servobrake and power steering are not operational until the
engine has been started, therefore much effort than usual is required on the brake
pedal and steering wheel.WARNING
Page 182 of 314

PARKING
Proceed as follows:
❒stop the engine and engage the handbrake;
❒engage a gear (on a slope, engage first gear if the car is faced uphill or
reverse if it is faced downhill) and leave the wheels steered.
Block the wheels with a wedge or a stone if the car is parked on a steep
slope. Avoid leaving the car parked with a wheel on the sidewalk or
steered against the kerb. Do not leave the ignition key at MAR to
prevent draining the battery. Always remove the key when you leave
the car.
181
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
HANDBRAKE
The handbrake lever is located between the two front seats.
Pull the handbrake lever upwards until the car cannot be moved.
Four or five clicks are generally enough when the car is on level ground while nine or ten may be required if the car
is on a steep slope or laden.
IMPORTANT If this is not the case, contact Fiat Dealership to have the handbrake adjusted.
When the handbrake lever is pulled up and the ignition key is at MAR the panel warning light xwill come on.
To release the handbrake:
❒slightly lift the handbrake and press release button (A);
❒keep button (A) pressed in and lower the lever. Warning light xwill go out.
Press the brake pedal when carrying out this operation to prevent the car from moving accidentally.
IMPORTANT If the handbrake lever tends to approach the end of stroke (slot on central console), contact Fiat
Dealership to have the handbrake adjusted.
WARNINGNever leave children unattended in the car. Always remove the ignition key when
leaving the car and take it out with you.
F0H0149m
Page 186 of 314

TOWING TRAILERS
IMPORTANT NOTES
For towing caravans or trailers the car must be fitted
with a certified tow hook and an adequate electric
system. Installation should be carried out by
specialised personnel who release a special document
for circulation on the road.
Install any specific and/or additional rear-view mirrors
as specified by law.
Remember that when towing a trailer, steep hills are
harder to climb, the braking spaces increase and
overtaking takes longer depending on the overall
weight.
Engage a low gear when driving downhill, rather than
constantly using the brake.The weight the trailer exerts on the car tow hook
reduces by the same amount the actual vehicle loading
capacity. To make sure the maximum towable weight
is not exceeded (given in the log book) account should
be taken of the fully laden trailer, including accessories
and personal belongings.
Do not exceed the speed limits of the country you are
driving in. In any case do not exceed 100 km/h.
185
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR
WARNING
Under no circumstances should the vehicle brake system be altered to control the
trailer brake. The trailer braking system must be fully independent of the vehicle’s
hydraulic system.WARNING
The ABS system with which the car may be fitted does not control the trailer
braking system. Great care should therefore be taken when driving on slippery
road surfaces.
Page 187 of 314

INSTALLING THE TOW HOOK
The towing device should be fastened to the body by
specialised personnel according to any additional
and/or integrative information supplied by the
Manufacturer of the device.
The towing device must meet current regulations with
reference to 94/20/EC Directive and subsequent
amendments.
For any version the towing device used must match
the towable weight of the vehicle on which it is to be
installed.
For the electric connection a unified connector should
be used which is generally placed on a special bracket
normally fastened to the towing device, and a special
ECU for external trailer light control shall be installed
on the car. For the electrical connection 7 or 13 pins 12VDC
connection is to be used (CUNA/UNI and ISO/DIN
Standards). Follow the instructions provided by the car
manufacturer and/or the tow hitch manufacturer.
An electric brake should be supplied directly by the
battery through a cable with a cross section of no less
than 2.5 mm
2.
IMPORTANT Electric brake or other device shall be
used with running engine.
In addition to the electrical branches, the car’s electric
system can only be connected to the supply cable for
an electric brake and to the cable for an internal light,
though not above 15W.
For connections use a preset control unit with battery
cable no less than 2.5 mm
2.
186
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CORRECT USE
OF THE CAR