climate control FIAT PUNTO EVO 2010 1.G User Guide
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 60 of 270

Enabling the AQS (Air Quality System) function
The AQS function (AQS appears on the display), auto-
matically activates internal air recirculation when the out-
side air is polluted (e.g. in traffic queues and tunnels).
IMPORTANT With the AQS function active, after 15 con-
secutive minutes of the internal air recirculation system
functioning, the climate control system enables the intake
of outside air for approximately 1 minute to freshen the
air in the passenger compartment. This takes place re-
gardless of the pollution level of the outside air.
SET TEMPERATURE ALIGNMENT
(MONO function)
Press the MONO button to align the temperature be-
tween the driver side and passenger side.
Then turn the AUTO or MONO knob to in-
crease/decrease the temperature between the two areas
by the same amount.
Press MONO again to deactivate the function.
CLIMATE CONTROL COMPRESSOR
ACTIVATION/DEACTIVATION
Press button òto switch on the climate control system
compressor.Compressor on
❒the LED on button òis lit up;
❒symbol òis shown on the display.
Compressor off
❒the LED on button òis lit up;
❒symbol òis shown on the display.
❒internal air recirculation is prevented;
❒the AQS function is disabled.
With the climate control compressor switched off, air can-
not be introduced into the passenger compartment at a
lower temperature than the outside; in this case the ò
symbol on the display will flash.
The deactivation of the climate control compressor is
memorized even after the engine has stopped. To turn the
climate control compressor back on, press button òonce
again or press AUTO: if you press AUTO, the other man-
ual settings will be cancelled.
SETTING THE AIR DISTRIBUTION
Press one or more of buttons Q/E/Zto manually select
one of the 7 possible air distribution settings for the pas-
senger compartment:
QAir flow to the windscreen and front side window
vents to demist/defrost them.
ZAir flow to the front and rear footwell vents. This
air distribution warms up the passenger compart-
ment quickly.
59
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 59
Page 61 of 270

Q
ZEAir flow distribution between front and rear vents,
centre/side dashboard vents, rear vent and wind-
screen and front side window demisting/defrosting
vents.
EAir flow distribution to centre/side dashboard vents
(passenger’s body).
QAir flow distribution between the footwell
Zvents and the windscreen and front side window
demisting/defrosting vents. This distribution setting
allows warms up the passenger compartment and
prevents the windows from misting up.
ZEAir flow distribution between footwell vents (hot-
ter air) and centre/side dashboard vents and rear
vent (cooler air).
EQAir flow distribution between centre/side dash-
board vents, rear vent and windscreen and front
side window demisting/defrosting vents. This dis-
tribution setting ventilates the passenger compart-
ment and prevents the windows from misting up.
IMPORTANT For the climate control system to function,
at least one of the following buttons must be on: Q/E/Z.
The system does not allow all the buttons Q/E/Zto be
switched off.
IMPORTANT Push the OFF button to turn the climate
control system back on: in this way, all previously saved
operating conditions are restored before switching off.
To restore automatic control of the air distribution after
a manual selection, press the AUTO button.ADDITIONAL HEATER
(for versions/markets where provided)
This device warms up the passenger compartment more
quickly when it is very cold and the engine coolant tem-
perature is low.
In these conditions, the device comes on automatically
when the engine is started and the fan is on.
The additional heater turns off automatically after reach-
ing the required comfort conditions.
IMPORTANT The heater will not turn on if the battery
voltage is too low.
SWITCHING OFF THE CLIMATE CONTROL
SYSTEM
Press the OFF button.
The following information is shown on the display:
❒ the word OFF;
❒outside temperature reading;
❒indication that air recirculation is switched on (LED on
button
Tis lit).
60
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 60
Page 117 of 270

116
F0U0202mfig. 120
NO ENGINE CUT-OUT
CONDITIONS
With the device activated, for reasons of comfort, limiting
emissions and safety, the engine does not stop in certain
conditions, including:
❒ engine still cold;
❒particularly cold external temperatures, where the ap-
propriate indication is provided;
❒ battery not sufficiently charged;
❒ heated rear windscreen activated;
❒ windscreen wipers working at maximum speed;
❒diesel particulate filter (DPF) regeneration ongoing (for
versions/markets where provided);
❒ driver’s door not shut;
❒ driver’s seat belt not fastened;
❒ reverse gear engaged (for example, during parking ma-
noeuvres);
❒automatic climate control, if a comfortable temperature
has not yet been reached or MAX – DEF function en-
abled;
❒during the first period of use, to initialize the system.
In the above cases, an information message appears on the
display and (for versions/markets where provided) the warn-
ing light fig. 118 will flash on the instrument panel. With Dualogic gearbox
(for versions/markets where
provided)
If the gear lever is in position N, place it in any other gear,
otherwise release the brake pedal or move the gear lever
to (+), (–) or R .
MANUAL ACTIVATION AND
DEACTIVATION
You can activate/deactivate the device by pressing the but-
ton on the dashboard fig. 120. When the system is
switched off, “Start&Stop OFF” appears on the dashboard
fig. 119.
In addition, (for versions/markets where provided) addi-
tional indications concerning the deactivation or activation
of Start&Stop is given through a message on the
display.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 116
Page 118 of 270

117
F0U0203mfig. 121
SAFETY FUNCTIONS
In engine cut-out conditions through the Start&Stop sys-
tem, if the driver unfastens his/her seat belt and opens the
driver’s door or the passenger door, the engine can be
restarted only by using the key.
The driver is notified of this condition both by a buzzer
and through an information message on the display and
(for versions/markets where provided) by the warning light
fig. 121 on the instrument panel flashing.
ENERGY SAVING FUNCTION
(For versions/markets where provided)
If, after the engine has been automatically restarted, the
driver does not take any action for a period of about 3
minutes, the Start&Stop system will definitively stop the
engine to avoid fuel consumption. In these cases, the en-
gine can be restarted only by using the key.
NB: In any case, it is possible to keep the engine running
by deactivating the Start&Stop system. RESTARTING CONDITIONS
For reasons of comfort, limiting harmful emissions and safe-
ty purposes, the power unit can restart automatically with-
out any action on behalf of the driver if certain conditions
are met, including:
❒ battery not sufficiently charged;
❒ windscreen wipers working at maximum speed;
❒extreme braking system pressure, e.g. following the
brake pedal being pressed repeatedly;
❒ car moving around, for example when driving on hilly
roads;
❒stopping the engine through the Start&Stop system for
more than about three minutes.
❒automatic climate control system for establishing a com-
fortable temperature or enabling the MAX – DEF func-
tion.
With a gear engaged, the engine can be automatically
restarted only by fully depressing the clutch pedal. The dri-
ver is asked to perform this operation through a message
on the instrument panel and, where provided, by the warn-
ing light fig. 121 on the instrument panel flashing
NB: If the clutch is not pressed, when the three minutes
have elapsed since the engine was stopped, the engine can
be restarted only by using the key.
NB: In cases when the engine stops and this is not desired,
due for example to the clutch pedal being released sharply
with a gear engaged, if the Start&Stop system is activat-
ed, the engine can be restarted by fully depressing the
clutch pedal or by putting the gear lever into neutral.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 117
Page 121 of 270

120
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0206mfig. 124a
IMPORTANT
Before opening the bonnet, make sure
that the car is switched off and the key is
in the OFF position. Follow the instructions on the
plate near the front crossmember fig. 124a. It is
advisable to extract the key when there are oth-
er people in the car. The car should always be
evacuated after the key has been removed or
turned to the OFF position. During refuelling op-
erations, it is necessary to make sure that the car
is off with the ignition key in the OFF position.
WARNING
For cars with a robotised transmission, if
the engine cuts out automatically on a
gradient, it is advisable to restart the engine by
moving the gear lever towards (+) or (-) without
releasing the brake pedal. For vehicles with Dua-
logic transmission, where the Hill Holder function
is present, if the engine cuts out automatically
whilst on a hill, it is advisable to restart it by mov-
ing the gear lever towards (+) or towards (-) with-
out releasing the brake pedal to make the Hill
Holder function – which is active only when the
engine is running – available.
WARNING
If you want to prioritise climate comfort,
the Start&Stop system can be disabled to
allow continuous operation of the climate control
system.
WARNING
082-128 PUNTO FL EN 4ed 20-01-2010 15:07 Pagina 120
Page 204 of 270

203
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
7.5
7.5
5
5
10
5
20
20
20
20
5
5
7.5 1
8
13
2
5
11
4
6
14
7
12
3
10
FUSE TABLE
Dashboard fuse box fig. 190
DEVICESFUSE AMPS
Right dipped beam headlight
Lift dipped beam headlight, headlamp alignment corrector
INT/A supply for switch coils on engine fuse box
and switch coils on body computer control unit
Front ceiling light, rear ceiling light, visor lights,
door marker lights, boot light, glove box light
Supply and battery for EOBD diagnostic plug, automatic climate
control system control unit, alarm, sound system, convergence control unit
INT supply for instrument panel, switch on brake pedal
(N.O. contact), third brake light
Door locking/unlocking motors, dead lock activation motors, boot
unlocking motor
Windscreen/rear window washer pump
Electric window motor on driver-side front door
Electric window motor on passenger-side front door
INT supply for dashboard control lights, parking control unit,
tyre pressure measurement control unit, electric wing mirror movement,
rain sensor, sunroof control unit, My Port infotelematic system socket,
electric rear view mirror
Instrument panel
INT supply for brake pedal switch (NC contact), clutch pedal switch,
interior heating unit, convergence control unit, sound system capabilities,
voltage stabiliser control unit, reverse light on rear bumper,
water sensor on diesel filter, glow plug heating control unit, airflow meter,
brake booster sensor, switch coils on engine compartment fuse box
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 203
Page 253 of 270

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
252
Lubricants and
greases
for drive
transmission
system
Brake liquid
Fuel additive
Windscreen/
rear window
washer fluid
Mechanical gearbox
and differential (petrol
versions and 1.3
Multijet 75HP version)
Mechanical gearbox
and differential (1.3
Multijet 90HP and
1.6 Multijet versions)
Wheel side
constant-velocity
joints
Differential side
constant-velocity
joints (1.6 Multijet
versions excluded)
Differential side
constant-velocity joints
(1.6 Multijet versions)
Hydraulic brakes
and hydraulic clutch
controls
Cooling circuits.
Mixture: 50% water
and 50%
PARAFLU
UP(❒)
Mix 25cc per 10 litres
of diesel
To be used diluted or
undiluted in windscreen/
rear window washer/
wiper systems
SAE 75W-85 grade synthetic base lubricant.
FIAT 9.55550-MX3 certification
SAE 75W-85 grade synthetic base lubricant.
FIAT 9.55550-MZ1 certification
Molybdenum disulphide grease, for use at
high temperatures.
FIAT 9.55580 certification. NL.GI. 1-2 consistency
Grease for constant-velocity joints with low
friction coefficient.
FIAT 9.55580 certification. NL.GI. 0-2 consistency
Polyeura-based synthetic grease for high temperatures.
FIAT 9.55580 certification. NL.GI. 2 consistency
Synthetic fluid FMVSS n° 116 DOT 4, ISO 4925
SAE J1704, CUNA NC 956- 01.
FIAT 9.55597 certification
Red protective with antifreeze action, based on inhibited
monoethyl glycol with organic formula. Exceeds CUNA
NC 956-16, ASTM D 3306 specifications.
FIAT 9.55523 certification
Additive for diesel antifreeze, protecting
diesel engines
Mixture of alcohol, water and surfactants CUNA NC
956-II
FIAT 9.55522 certification.TUTELA CAR
TECHNYX
Contractual Technical
Reference N° F010.B05
TUTELA CAR
MATRYX
Contractual Technical
Reference N° F108.F02
TUTELA ALL STAR
Contractual Technical
Reference N° F702.G07
TUTELA STAR 700
Contractual Technical
Reference N° F701.C07
TUTELA STAR 325
Contractual Technical
Reference N° F301.D03
TUTELA TOP 4
Contractual Technical
Reference N° F001.A93
PARAFLU
UP(*)
Contractual Technical
Reference N° F101.M01
TUTELA DIESEL ART
Contractual Technical
Reference N° F601.L06
TUTELA
PROFESSIONAL SC 35Contractual Technical
Reference N° F201.D02
Radiator
protection Use Quality specifications of fluids and lubricants Original Applications
for correct car operation fluids and lubricants
(*) IMPORTANT Do not use fluids with other specifications for topping up or mixing.
(❒) When the vehicle is used in particularly harsh climate conditions, we recommend using a 60-40 mixture of PARAFLUUPand distalled water.
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 252
Page 254 of 270

KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
253
FUEL CONSUMPTION
The fuel consumption figures given in the table below are
determined on the basis of the homologation tests set
down by specific European Directives.
The procedures below are followed for measuring con-
sumption:
❒urban cycle: cold starting followed by driving that sim-
ulates urban use of the car;
❒extra-urban cycle: driving that simulates using the ve-
hicle out of town with frequent acceleration in all gears;
the speed varies from 0 to 120 km/h;
❒combined consumption: this is calculated with a weight-
ing of about 37% urban cycle consumption and about
63% extra-urban consumption.
IMPORTANT The type of route, traffic situations, weath-
er conditions, driving style, general state of the car, trim
level/equipment/accessories, load, climate control system,
roof rack, and other situations that affect how the car
moves through the air may lead to different fuel con-
sumption levels than those measured.
Fuel consumption according to the current European directive (litres x 100 km)
Versions Urban Extra-urban Combined
1.27,3 4,8 5,7
1.4 7,4 4,7 5,7
1.4 Multi Air 7,5 4,7 5,7
1.4 Turbo Multi Air 7,3 4,6 5,6
1.3 Multijet 70HP (❒)4,9 3,4 4,0
1.3 Multijet 75HP (❍)5,1 3,3 4,0
1.3 Multijet 75
HP5,2 3,5 4,1
1.3 Multijet 90
HP5,9 3,7 4,5
1.3 Multijet 95HP5,3 3,5 4,2
1.6 Multijet 120HP5,8 3,8 4,5
(❒) For versions/markets where provided(❍) ECO versions
235-258 PUNTO FL EN 4ed 18-01-2010 12:28 Pagina 253
Page 260 of 270

259
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
– extending the boot ....................... 94
– parcel shelf (removing) ................ 96
– removing the parcel shelf ............ 96
– unlocking with remote control..6
Boot courtesy light .............................. 197
Brake Assist system............................ 104
Brake fluid
– checking and topping up .............. 224
– specifications.................................. 252
Brake lights
– bulb replacement ...............193-194
Brakes
– brake fluid (type)........................... 252
– checking and topping
up fluid level .................................. 224
– handbrake ....................................... 152
– technical specifications................. 241
Bulbs
– bulb types......................186-187-188
– general information on
replacing.......................................... 186
Capacities
– technical specifications
(quantities)...................................... 250
Capacity for installing child seats........ 138
Car dimensions .................................... 246
Car identification data ........................ 235
Carrying children ................................ 134
Catalytic converter ............................ 128
Central locking .................................... 73Changing a wheel ................................ 176
– general information and
warnings.......................................... 176
– tyre inflation pressure ................ 245
– tyre and rim types ....................... 244
Changing bulbs
– bulb types ...................................... 186
– general information ..................... 186
– inside .............................................. .195
– outside ........................................... 189
Chassis (marking) ............................... 236
Checking engine oil ............................ 220
– consumption ................................. 220
– engine oil specifications .............. 251
Checking levels ................................... 217
– brake fluid ...................................... 224
– engine cooling fluid ...................... 222
– engine oil ....................................... 220
– windscreen/rear window
washer fluid ................................... 223
Child safety .......................................... 84
Child safety device ............................. 87
Child seats ............................................ 138
– capacity for installing child
seats ................................................ 138
– suitability for using child seats..... 137
Children (carrying them safely) ........ 134
– acity for installing an Isofix
child seat ........................................ 138
Cigarette lighter .................................. 78 ABS ....................................................... 103
ABS system .......................................... 103
Additional brake light
– bulb replacement ......................... 194
Adjusting the lighting inside the car 18
Adjusting the mirrors ....................... 44
Adjusting the seats ......................39-41
Adjusting the steering wheel ............ 43
Air conditioning controls ............ 52-56
Air filter ................................................ 225
Air recirculation ....................51-55-58
Air vents................................................ 48
Ashtray................................................... 78
ASR function / system ....................... 107
Automatic climate control................. 56
Battery
– jump starting .................................. 175
– maintenance................................... .225
– replacement .................................. 226
– tips for extending life ................... 226
Bodywork
– bodywork version codes............. 237
– cleaning, care and maintenance.. 231
Bodywork codes ................................. 237
Bodywork versions ............................ 237
Bonnet
– opening/closing ...............97-98-99
Boot ........................................................ 92
– emergency unlocking from
the inside......................................... 94
CONTENTS
259-268 PUNTO FL EN 4ed 18-01-2010 12:29 Pagina 259
Page 261 of 270

260
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Cleaning and maintenance
– bodywork ...................................... 231
– engine compartment ................... 233
– fabric seats .................................... 234
– interiors ......................................... 233
– leather upholstery ....................... 234
– windows ......................................... 233
– plastic parts ................................... 234
Climate control ................................... 53
– air vents ..................................47-48
Clock
– adjusting ......................................... 30
Clutch
– technical specifications ............... 240
CO
2emissions at exhaust ................ 254
CODE card .......................................... 5
Control buttons .................................. 71
Cruise Control .................................... 66
Dashboard ....................................3-265
Deactivating airbags .....................36-143
Dead lock ............................................. 86
Defrosting/demisting
– rear window ....................51-55-72
– windscreen and front
side windows ..................50-54-57
Demisting/defrosting
– rear window ....................51-55-72
– windscreen and front
side windows....................50-54-57
– wing mirrors.....................51-55-58
Digital display ........................................ 17
– control buttons ............................ 18
– setup menu ................................... 18
– standard screen ............................ 17Dipped beam headlights
– bulb replacement ........................ 190
– switching on ................................. 61
Dipped beam headlights
– bulb replacement ........................ 190
– switching on ................................. 61
Direction indicators
– switching on ................................. 62
– front bulb replacement ............. 191
– rear bulb replacement ................ 193
Direction indicators
– switching on ................................. 62
– front bulb replacement ............. 191
– rear bulb replacement ................ 193
Direction Indicators
– switching on ................................. 62
– front bulb replacement ............. 191
– side bulb replacement ................. 192
– rear bulb replacement ............... 193
Disposing of the car ........................... 255
Door locks ........................................... 73
Doors
– central locking .............................. 73
– child safety device ........................ 87
– locking/unlocking
from the inside ......................73-84
– remote control ............................ 6
– remote locking/unlocking ........... 6
DPF (particulate filter) ....................... 128
Driving economically ......................... 154
Electrical/electronic devices ............ 124
Emergency rear door locking
device ................................................. 88Emergency starting ............................. 175
– bump starting ................................ 176
– jump starting ................................. 175
End of vehicle life ................................ 255
Engine
– engine immobiliser (Fiat CODE) .. 4
– identification codes ..................... 237
– marking .......................................... 236
– technical specifications ............... 238
Engine codes ........................................ 237
Engine compartment
– checking levels .............................. 217
– opening/closing the bonnet ....... 97
– washing ......................................... 233
Engine coolant
– checking levels and topping up ... 222
– specifications ................................. 252
Engine coolant
– checking and topping up ............. 222
– specifications ................................. 252
– temperature gauge and
warning light .................................. 16
Engine coolant temperature
gauge ................................................... 16
– type of coolant ............................. 222
Engine cooling
– checking levels and topping up ... 222
– specifications ................................. 252
Engine immobiliser (Fiat CODE) ...... 4
Engine marking .................................... 236
Engine oil
– checking levels and topping up ... 220
– consumption ................................. 220
– specifications ................................. 251
259-268 PUNTO FL EN 4ed 18-01-2010 12:29 Pagina 260