Heat FIAT PUNTO EVO 2010 1.G Owner's Manual

150
If, when the ignition key is at MAR, the instrument panel
warning light
Yremains on together with warning light
U, turn the key to STOP and then back to MAR; if the
warning light remains on, try with the other keys provid-
ed with the car.
IMPORTANT If the instrument panel warning light
Ystays on permanently, contact a Fiat Dealership immedi-
ately.
IMPORTANT Never leave the ignition key at MAR when
the engine is off.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTSSTARTING PROCEDURE FOR DIESEL
VERSIONS
Proceed as follows:
❒ensure that the handbrake is on;
❒put the gear lever into neutral;
❒turn the ignition key to MAR: the warning lights mand
Yon the instrument panel will turn on;
❒wait for the warning lights Yand m to turn off. The
hotter the engine is, the quicker this will happen;
❒fully depress the clutch pedal without touching the ac-
celerator;
❒turn the ignition key to AVV as soon as warning light
m goes out. If you wait too long, you will lose the ben-
efit of the heating work done by the glow plugs. Release
the key as soon as the engine starts.If the engine does not start at the first attempt, return
the ignition key to STOP before repeating the procedure.
If, when the ignition key is at MAR, the instrument panel
warning light
Yremains on together with warning light
m, turn the key to STOP and then back to MAR; if the
warning lights remain on, try with the other keys provid-
ed with the car.
IMPORTANT If the instrument panel warning light
Ystays on permanently, contact a Fiat Dealership immedi-
ately.
IMPORTANT Never leave the ignition key at MAR when
the engine is off.
Warning light mwill blink for 60 seconds
after starting or during prolonged crank-
ing to indicate a fault with the glow plug
system. Use the car as normal if the engine starts,
but go to a Fiat Dealership as soon as possible.
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 150

154
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SAVING FUEL
Here are some suggestions which may help you to save fu-
el and reduce the amount of toxic emissions released in-
to the atmosphere.
GENERAL CONSIDERATIONS
Car maintenance
Have checks and adjustments carried out in accordance
with the “Scheduled Servicing Plan”.
Tyres
Check the tyre pressures at least once every 4 weeks: if
the pressure is too low, consumption levels increase as re-
sistance to rolling is higher.
Unnecessary loads
Do not travel with an overloaded boot. The weight of
the car (especially when driving in town) and its arrange-
ment greatly affect fuel consumption and stability.
Roof rack/ski rack
Remove the roof rack or ski rack from the roof after use.
These accessories decrease aerodynamic penetration and
have a negative effect on fuel consumption. It is better to
use a trailer to transport particularly bulky objects.Electrical devices
Use electrical devices only for the amount of time need-
ed. The heated rear window, auxiliary headlights, wind-
screen wipers and fan heater use up a considerable amount
of current, causing increased fuel consumption (up to
+25% in the urban cycle).
Air conditioning
Air conditioning leads to higher fuel consumption (on av-
erage up to +20%). If the temperature outside is not too
extreme, try and use the air vents.
Spoilers
The use of non-certified spoilers may adversely affect aero-
dynamics and fuel consumption.
DRIVING STYLE
Starting
Do not warm up the engine at low or high revs when the
vehicle is stationary; this causes the engine to warm up more
slowly, thereby increasing fuel consumption and emissions.
It is advisable to set off immediately and slowly, avoiding high
revs: this allows the engine to warm up more quickly.
Unnecessary actions
Avoid revving up when stationary at traffic lights or before
stopping the engine. The latter action, like double de-
clutching, is entirely unnecessary and causes increased fu-
el consumption and pollution.
149-160 PUNTO FL EN 4ed 20-01-2010 14:37 Pagina 154

162
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
AIRBAG FAILURE (red)
When the ignition key is moved to MAR position,
the warnintg light turns on but should go off af-
ter a few seconds.
The warning light stays on constantly if there is a failure
in the airbag system. A specific message is displayed on cer-
tain versions.
¬
If the warning light ¬does not come on
when turning the key to MAR or stays on
during car travel, a failure may be present in the
restraint systems. If this is the case, the airbags
or pretensioners may not be deployed after an im-
pact or, in a minor number of cases, they may be
deployed accidentally. Contact a Fiat Dealership
immediately to have the system checked before
driving off.
WARNING
A problem with the warning light ¬(light
off) is indicated by the warning light “,
which indicates the front passenger airbag is de-
activated, flashing for more than the usual four
seconds.
WARNING
OVERHEATED ENGINE COOLANT
(red)
When the ignition key is moved to MAR position,
the warnintg light turns on but should go off after a few
seconds. The warning light turns on when the engine is
overheated. If the warning light comes on, proceed as fol-
lows:
❒when driving normally: stop the car, switch off the en-
gine and check that the water level in the reservoir is
not below the MIN mark. If it is not, wait for a few min-
utes for the engine to cool down then slowly and care-
fully open the cap, top-up with coolant and check that
the level is between the MIN and MAX marks. Also
visually check for leaks. Go to a Fiat Dealership if the
warning light comes on again when the engine is next
started.
❒if the vehicle is used under demanding conditions (e.g.
towing trailers uphill or fully loaded): slow down and,
if the light stays on, stop the car. Stop for 2 or 3 min-
utes with the engine running and slightly accelerated to
assist better coolant circulation. Then switch the en-
gine off. Check correct fluid level as described above.
IMPORTANT On particularly demanding journeys, it is ad-
visable to keep the engine on and slightly accelerated for
a few minutes before switching it off.
A specific message is displayed on certain versions.
ç
161-174 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 162

167
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
FUEL RESERVE (amber)
Turning the key to the MAR position illuminates
the warning light, but it will switch off after a few
seconds.
The warning light turns on when about 7 litres of fuel are
left in the tank.
IMPORTANT The warning light will blink to indicate a sys-
tem failure. If this happens, go to a Fiat Dealership to have
the system checked.
Warning light “indicates a failure of warn-
ing light ¬. This condition is indicated by
intermittent blinking of warning light “for longer
than 4 seconds. In this case, warning light ¬may
not be indicating that there is a fault in the restraint
systems. Before driving off, contact a Fiat Dealer-
ship to have the system checked immediately.
WARNING
ç
ABS SYSTEM FAULT (amber)
Turning the key to the MAR position illuminates
the warning light, but it will switch off after a few
seconds.
The warning light comes on when the system is either not
working properly or not available. Under these circum-
stances, the braking system will work as normal but without
the extra performance offered by the ABS system. Drive
carefully and go to a Fiat Dealership as soon as possible.
On some versions the display shows the associated message.
>
GLOW PLUG PREHEATING
(Multijet versions – amber)
GLOW PLUG PREHEATING FAULT
(Multijet versions – amber)
Glow plugs
This warning light comes on when the key is turned to
MAR. It will go out as soon as the glow plugs have reached
a preset temperature. Start the engine as soon as the
warning light goes out.
IMPORTANT When it is particularly warm outside, the
warning light stays on for an extremely short time.
Glow plug preheating fault
The warning light flashes if there is a fault in the preheat-
ing system. Go to a Fiat Dealership as soon as possible.
A specific message is displayed on certain versions.
m
161-174 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 167

172
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
IMPORTANT Do not continue driving with one or more
flat tyres as handling may be compromised. Stop the car,
avoiding harsh braking or steering manoeuvres. Replace
the wheel immediately with the small spare wheel (for ver-
sions/markets where provided) or carry out a repair us-
ing the dedicated kit (see “Changing a wheel” in the “In
an emergency” section) and contact a Fiat Dealership as
soon as possible.
Tyre pressure unsuitable for speed
Should you need to travel at a speed higher than 160 km/h,
inflate the tyres to the pressures specified in “Tyre pres-
sures”.
If the TPMS system (for versions/markets where provid-
ed) detects that the pressure of one or more tyres is un-
suitable for the current speed, the warning light will turn
on (together with the message on the display) (see “Tyre
pressure low” in this section) and it will stay on until the
car slows down to a speed below the preset threshold.
IMPORTANT In this case, slow down immediately because
tyre overheating could damage tyre performance and dura-
bility beyond repair, and may even make the tyre explode. CHECK TYRE PRESSURE
(amber)
TYRE PRESSURE LOW (amber)
TYRE PRESSURE UNSUITABLE FOR
SPEED
(amber)
(for versions/markets where provided)
When the ignition key is moved to MAR position, the
warnintg light turns on but should go off after a few sec-
onds.
Check tyre pressures
The warning light turns on to indicate the flat tyre. Should
two or more tyres be flat, the display will show the indi-
cations corresponding to each tyre in sequence.
Restore correct tyre pressures as soon as possible (see
“Cold tyre pressures” in the “Technical specifications” sec-
tion).
Tyre pressure low
The warning light on the panel comes on when the pres-
sure of one or more tyres falls below a preset level. In this
way, the TPMS system warns the driver that one or more
tyres may be dangerously flat and probably punctured.
n
161-174 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 172

In the event of a puncture caused by for-
eign bodies, it is possible to repair tyres
showing holes on the track or shoulder of
up to 4 mm in diameter.
It is not possible to repair damage to the
tyre sidewall. Do not use the quick repair kit
if the tyre is damaged as a result of travelling on a
flat tyre.
WARNING
If the wheel rim is damaged (the channel
is so deformed as to cause an air leakage)
it cannot be repaired. Do not remove foreign bod-
ies (screws or nails) from the tyre.
WARNING
IMPORTANT INFORMATION:
The sealing fluid of the quick tyre repair kit is effective at
external temperatures of between –20 °C and +50 °C.
The sealant has an expiry date.
Do not operate the compressor for longer
than 20 minutes at a time. Risk of over-
heating. The quick repair kit is not suitable for de-
finitive repairs, so you can only temporarily repair
the tyres.
WARNING
The canister contains ethylene glycol. It
contains latex, which may cause an aller-
gic reaction. Harmful if swallowed. Irritates the
eyes. There could be a reaction in case of inhala-
tion or contact. Avoid contact with your eyes, skin
and clothes. In the event of contact, wash imme-
diately with plenty of water. Do not induce vom-
iting if swallowed. Rinse your mouth out and drink
plenty of water. Call a doctor immediately. Keep
out of the reach of children. The product must not
be used by asthmatics. Do not breathe in the
vapours during insertion and suction. Call a doc-
tor immediately if allergic reactions are noted.
Store the canister in its proper compartment,
away from sources of heat. The sealant fluid has
an expiry date.
WARNING
182
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 182

203
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
7.5
7.5
5
5
10
5
20
20
20
20
5
5
7.5 1
8
13
2
5
11
4
6
14
7
12
3
10
FUSE TABLE
Dashboard fuse box fig. 190
DEVICESFUSE AMPS
Right dipped beam headlight
Lift dipped beam headlight, headlamp alignment corrector
INT/A supply for switch coils on engine fuse box
and switch coils on body computer control unit
Front ceiling light, rear ceiling light, visor lights,
door marker lights, boot light, glove box light
Supply and battery for EOBD diagnostic plug, automatic climate
control system control unit, alarm, sound system, convergence control unit
INT supply for instrument panel, switch on brake pedal
(N.O. contact), third brake light
Door locking/unlocking motors, dead lock activation motors, boot
unlocking motor
Windscreen/rear window washer pump
Electric window motor on driver-side front door
Electric window motor on passenger-side front door
INT supply for dashboard control lights, parking control unit,
tyre pressure measurement control unit, electric wing mirror movement,
rain sensor, sunroof control unit, My Port infotelematic system socket,
electric rear view mirror
Instrument panel
INT supply for brake pedal switch (NC contact), clutch pedal switch,
interior heating unit, convergence control unit, sound system capabilities,
voltage stabiliser control unit, reverse light on rear bumper,
water sensor on diesel filter, glow plug heating control unit, airflow meter,
brake booster sensor, switch coils on engine compartment fuse box
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 203

09
10
14
15
19
20
21
30
84
85
86
87
8820
10
15
30
7.5
30
15
15
7.5
–
15
5
7.5
204
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Engine compartment fuse box fig. 192
DEVICESFUSE AMPS
Hi-Fi sound system with control unit and subwoofer
Single tone horn
Left main beam headlight, right main beam headlight
Additional heater PTC1
Air conditioning compressor
Heated rear window
Fuel pump on tank
Left fog light, right fog light
CNG methane system management solenoid valves
Socket (ready for use)
Passenger compartment socket, cigarette lighter
Battery charge status sensor
De-mister on driver-side wing mirror, de-mister on passenger-side wing mirror
175-210 PUNTO FL EN 4ed 20-01-2010 15:09 Pagina 204

205
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
17
14
01
03
04
15
10
16
08
07
05
11
13
09
06
0220
7.5
–
–
10
–
20
–
10
–
15
20
5
10
–
– Boot fuse box fig. 194
DEVICESFUSE AMPS
Sunroof opening system
Alarm system management control unit
Spare
Spare
Electric lumbar movement on driver’s seat
Spare
Electric windows system (motor, control unit) on right-hand door
Spare
Driver’s seat heater control unit
Tow hook system (capability for after-sale fuse assembly)
Boot socket
Electric windows system (motor, control unit) on left-hand door
TPMS (tyre pressure monitoring system) control unit
Front passenger seat heater control unit
Spare
Spare
175-210 PUNTO FL EN 4ed 20-01-2010 15:10 Pagina 205

●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●● ●● ● ●
●●
●●
●●
●● ●
●● ●● ● ●
212
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SCHEDULED SERVICING PLAN
EURO 4/EURO 5 PETROL AND EURO 4 DIESEL VERSIONS
Thousands of kilometres 30 60 90 120 150 180
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system (headlamps, direction indicators,
hazard warning lights, boot, passenger compartment, glove box,
instrument panel warning lights, etc.)
Check operation of windscreen washer system and adjust nozzles
if necessary.
Check windscreen/rear window wiper blade position/wear
Check conditions and wear of front/rear disc brake pads
(for versions/markets where provided) and operation of pad wear indicator
Check condition and wear of rear drum brake linings
Visually inspect the conditions of: bodywork,
underbody protection, pipes and tubes
(exhaust – fuel – brakes), rubber parts (boots, sleeves, bushes, etc.)
Check cleanliness of bonnet and boot locks, and the cleanliness
and lubrication of linkages
Check and, if necessary, top up fluid levels (brakes/hydraulic
clutch, windscreen washer, battery, engine coolant, etc.)
Check the handbrake lever stroke and adjust it, if necessary
Visually inspect the condition of accessory drive belt/s.
Visually inspect the condition of toothed timing belt
Check tension of accessory drive belt/s, and adjust if necessary
(versions 1.2 – 1.4 heated)
Check and, if necessary, adjust tappet clearance (1.2 8v – 1.4 8vversions)
Check exhaust gas emissions
211-234 PUNTO FL EN 4ed 18-01-2010 12:27 Pagina 212