fuel FIAT PUNTO EVO 2010 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2010, Model line: PUNTO EVO, Model: FIAT PUNTO EVO 2010 1.GPages: 270, PDF Size: 8.34 MB
Page 3 of 270
REFUELLING
Petrol engines: only refuel the car with unleaded
petrol with an octane rating (RON) of no less than 95
conforming to the European specification EN 228.
The use of petrol that does not conform to the above-
mentioned specification may cause the EOBD warning light
to switch on and the irregular operation of the engine.
Diesel engines: only refuel the car using diesel fuel that
conforms to European specification EN590.
STARTING THE ENGINE
Make sure that the handbrake is properly applied; place the
gear lever in neutral; fully depress the clutch pedal, with-
out pressing the accelerator, then turn the ignition key to
the MAR position and wait for the
Yand mwarning
lights to switch off (diesel versions); turn the ignition key to
the AVV position and release it as soon as the engine starts.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter reaches high temperatures dur-
ing operation. Do not park the on grass, dry leaves, pine
needles or other flammable material: fire hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that carries out a con-
tinuous diagnosis of the emission-related components
in order to help protect the environment.ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical ac-
cessories (with the risk of gradually draining the bat-
tery), visit a Fiat Dealership. They can calculate the over-
all electrical requirement and check that the car’s elec-
trical system can support the required load.
CODE card
Keep this in a safe place, not in the car. You should have
the electronic code from the CODE card with you at
all times.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring it
stays in tip-top condition and safeguards its safety features,
its environmental friendliness and low running costs for
a long time to come.
THE OWNER’S HANDBOOK CONTAINS…
... information, tips and important warnings on the cor-
rect use and maintenance of your car over time as
well as safe driving tips. Pay special attention to the sym-
bols
"(personal safety) #(environmental protection)
!(the car’s wellbeing).
READ THIS CAREFULLY!
K
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 2
Page 7 of 270
6
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0004mfig. 4
KEY WITH REMOTE CONTROL fig. 4
The metal insert A operates:
❒the ignition;
❒the door locks;
❒the fuel cap lock/release (for versions/markets where
provided);
Pressing button B opens/closes the metal insert.
All the keys and the CODE card must be
handed over to the new owner when selling
the car.
Only press button B with the key away
from your body, specifically from your
eyes and from objects which could get damaged
(e.g. your clothes). Do not leave the key unat-
tended to avoid the button being accidentally
pressed while it is being handled, e.g. by a child.
WARNING
Button Ëis used for unlocking the doors and the boot.
Button Áis used for locking the doors and the boot.
Button
Ris used to open the boot remotely.
When unlocking the doors, the passenger compartment
ceiling lights will come on for a preset time.
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 6
Page 10 of 270
KEY WITHOUT REMOTE CONTROL fig. 8
The metal insert A of the key is fixed.
The key operates:
❒the ignition;
❒the door locks;
❒the fuel tank cap lock (for versions/markets where pro-
vided).ALARM
The car’s alarm system is available from Lineaccessori Fiat.
fig. 8F0U0008m
9
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 9
Page 14 of 270
INSTRUMENT PANEL
Versions with digital display
A Speedometer
B Fuel level gauge with reserve
warning light
C Engine coolant temperature gauge
with overheating warning light
D Rev counter
E Digital display
Versions with
multifunction display
A Speedometer
B Fuel level gauge with reserve
warning light
C Engine coolant temperature gauge
with overheating warning light
D Rev counters
E Multifunction display
F0U0010mfig. 10
F0U0011mfig. 11
CONTENTS TECHNICAL
SPECIFICATIONS SERVICING
AND CARE IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR
VEHICLE
13
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 13
Page 15 of 270
Sport versions (with
multifunction display)
A Speedometer
B Fuel level gauge with reserve
warning light
C Engine coolant temperature gauge
with overheating warning light
D Rev counter
E Multifunction display
Versions with reconfigurable
multifunction display
A Speedometer
B Fuel level gauge with reserve
warning light
C Engine coolant temperature gauge
with overheating warning light
D Rev counters
E Reconfigurable multifunction dis-
play
F0U0012mfig. 12
F0U0013mfig. 13CONTENTS TECHNICAL
SPECIFICATIONSSERVICING
AND CAREIN AN
EMERGENCY WARNING LIGHTS
AND MESSAGESSTARTING
AND DRIVINGSAFETY
KNOWING
YOUR
VEHICLE
14
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 14
Page 16 of 270
INSTRUMENTS
Instrument background colour and type may vary ac-
cording to the version.
SPEEDOMETER fig. 14
This shows the speed of the vehicle.
REV COUNTER fig. 15
The rev counter shows the number of engine revolutions
per minute.
IMPORTANT The electronic injection control system
gradually shuts off the flow of fuel when the engine is over-
revving, resulting in a gradual loss of engine power.
When the engine is idling, the rev counter may indicate a
gradual or sudden increase of the rate.
This is normal and does not indicate a fault. It may becaused, for example, by the operation of the climate con-
trol system or fan. In these cases, a slow change in revs is
used to protect the battery charge.
FUEL GAUGE fig. 16
This shows the amount of fuel left in the tank.
E tank empty.
F tank full.
The reserve warning light A comes on to indicate that
approximately 7 litres of fuel are left in the tank.
Do not travel with the fuel tank almost empty: the gaps
in fuel delivery could damage the catalyst.
See the description in the “Refuelling” paragraph.
IMPORTANT The needle will point to E and warning light
A will blink to indicate a fault in the system. If this is the
case, go to a Fiat Dealership to have the system checked.
fig. 15F0U0015mfig. 14F0U0014m
CONTENTS TECHNICAL
SPECIFICATIONS SERVICING
AND CARE IN AN
EMERGENCY WARNING LIGHTS
AND MESSAGES STARTING
AND DRIVING SAFETY
KNOWING
YOUR
VEHICLE
15
001-036 PUNTO FL EN 4ed 18-01-2010 12:21 Pagina 15
Page 34 of 270
33
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
If the distance unit set is “mi” the fuel consumption unit
will be displayed in “mpg”.
– press +or –to make your choice;
– if selecting “Temperature”: briefly press MENU ESC and
the display will show “°C” or “°F” (depending on the pre-
vious setting);
– press +or –to make your choice.
When you have made the required adjustments, briefly
press MENU ESC to go back to the submenu screen or
hold the button down to go back to the main menu screen
without saving.
– hold down MENU ESC again to go back to the standard
screen or main menu, depending on which point in the
menu you have reached. MEASUREMENT UNITS
(Setting measurement units)
With this function it is possible to set the measurement
units through three sub-menus: “Distance”, “Consump-
tion” and “Temperature”.
To set the desired measurement unit, proceed as follows:
– briefly press MENU ESC to display the three submenus;
– press +or –to switch between the three sub-menus;
– once the submenu to be modified has been selected, briefly
press the MENU ESC button;
– if selecting “Distance”: briefly press MENU ESC and the
display will show “km” or “mi” (depending on the previ-
ous setting);
– press +or –to make your choice;
– if selecting “Consumption”: briefly press MENU ESC and
the display will show “km/l”, “l/100km” or “mpg” (de-
pending on the previous setting);
If the set distance unit is “km”, you can set the fuel con-
sumption unit to km/l or l/100km depending on the
amount of fuel consumed.
001-036 PUNTO FL EN 4ed 18-01-2010 12:22 Pagina 33
Page 38 of 270
37
Values displayed
Outside temperature
Indicates the temperature outside the vehicle passenger
compartment.
Range
This indicates the approximate distance that may be trav-
elled with the fuel remaining in the tank, assuming that dri-
ving conditions do not change. The display will show the
reading “----” when the following events take place:
– value lower than 50 km (or 30 mi)
– car left parked with engine running for a long time.
Distance travelled
This value shows the distance covered from the start of
the new journey.
Average consumption
This value shows the approximate average fuel consump-
tion from the start of the new journey.
Current consumption
Indicates the fuel consumption. The value is constantly up-
dated. The message “----” will appear on the display if the
car is parked with the engine running.
Average speed
This value shows the car’s average speed based on the
overall time elapsed since the start of the new journey.TRIP COMPUTER
Introduction
The Trip computer is used to display information on car
operation when the key is turned to MAR. This function
allows you to define two separate trips, called “Trip A”
and “Trip B”, for monitoring the car’s “complete mission”
(journey) in a reciprocally independent manner.
Both functions can be reset (reset – start of a new jour-
ney).
“Trip A” is used to display the figures relating to:
– Outside temperature
– Range
– Distance travelled
– Average consumption
– Current consumption
– Average speed
– Journey time (driving time).
“Trip B”, available on multifunction display only, is used to
display the figures relating to:
– Distance travelled B
– Average consumption B
– Average speed B
– Travel time B (driving time).
NB“Trip B” functions may be excluded (see “Trip B on”).
“Range” and “Instant consumption” parameters cannot be
reset.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 37
Page 74 of 270
73
F0U0005mfig. 63
DOOR LOCKING fig. 63
To lock all doors at the same time, press button A, located
on the centre console control panel, regardless of the po-
sition of the ignition key.
FUEL CUT-OFF SYSTEM
This system triggers after a collision and activates the fol-
lowing:
❒cut-off of fuel supply with consequent switching off of
the engine;
❒automatic door unlocking;
❒switching on of all interior lights.
The intervention of the system is indicated by a message
shown on the display. Carefully check the car for fuel leaks,
for instance in the engine compartment, under the car or
near the tank area. After a crash, turn the key to STOP
to avoid draining the battery.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
If, after a crash, you smell fuel or notice
leaks from the fuel system, do not reacti-
vate the system to avoid the risk of fire.
WARNING
Door unlocking in the event of an accident
If the fuel cut-off system activates following an accident,
the doors will be automatically unlocked to allow access
to the passenger compartment and the ceiling lights will
be switched on at the same time. The doors can always be
opened from the inside of the car by using the appropri-
ate controls. if no fuel leakage is found and the car is road-
worthy, ensure the correct operation of the vehicle by ad-
hering to the following instructions.
The following procedure should be carried out to restore
the correct operation of the vehicle:
❒turn the ignition key to MAR;
❒activate the right-hand indicator;
❒deactivate the right-hand indicator;
❒activate the left-hand indicator;
❒deactivate the left-hand indicator;
❒activate the right-hand indicator;
❒deactivate the right-hand indicator;
❒activate the left-hand indicator;
❒deactivate the left-hand indicator;
❒turn the key to STOP.
037-081 PUNTO FL EN 4ed 18-01-2010 12:23 Pagina 73
Page 118 of 270
117
F0U0203mfig. 121
SAFETY FUNCTIONS
In engine cut-out conditions through the Start&Stop sys-
tem, if the driver unfastens his/her seat belt and opens the
driver’s door or the passenger door, the engine can be
restarted only by using the key.
The driver is notified of this condition both by a buzzer
and through an information message on the display and
(for versions/markets where provided) by the warning light
fig. 121 on the instrument panel flashing.
ENERGY SAVING FUNCTION
(For versions/markets where provided)
If, after the engine has been automatically restarted, the
driver does not take any action for a period of about 3
minutes, the Start&Stop system will definitively stop the
engine to avoid fuel consumption. In these cases, the en-
gine can be restarted only by using the key.
NB: In any case, it is possible to keep the engine running
by deactivating the Start&Stop system. RESTARTING CONDITIONS
For reasons of comfort, limiting harmful emissions and safe-
ty purposes, the power unit can restart automatically with-
out any action on behalf of the driver if certain conditions
are met, including:
❒ battery not sufficiently charged;
❒ windscreen wipers working at maximum speed;
❒extreme braking system pressure, e.g. following the
brake pedal being pressed repeatedly;
❒ car moving around, for example when driving on hilly
roads;
❒stopping the engine through the Start&Stop system for
more than about three minutes.
❒automatic climate control system for establishing a com-
fortable temperature or enabling the MAX – DEF func-
tion.
With a gear engaged, the engine can be automatically
restarted only by fully depressing the clutch pedal. The dri-
ver is asked to perform this operation through a message
on the instrument panel and, where provided, by the warn-
ing light fig. 121 on the instrument panel flashing
NB: If the clutch is not pressed, when the three minutes
have elapsed since the engine was stopped, the engine can
be restarted only by using the key.
NB: In cases when the engine stops and this is not desired,
due for example to the clutch pedal being released sharply
with a gear engaged, if the Start&Stop system is activat-
ed, the engine can be restarted by fully depressing the
clutch pedal or by putting the gear lever into neutral.KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
082-128 PUNTO FL EN 4ed 20-01-2010 15:06 Pagina 117