Side light FIAT STILO 2006 1.G Manual Online

179
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒make sure the compressor switch E-
fig. 16is set to 0(off), start the en-
gine and fit plug D-fig. 15into the cig-
ar lighter outlet and then turn on the
compressor by setting switch E-fig. 16
to I(on). Inflate the tyre to the pres-
sure specified in paragraph “Cold tyre
inflation pressure” in section “Techni-
cal Specifications”. Check tyre pressure
on gauge F-fig. 16with compressor off
to obtain precise reading; ❒If after 5 minutes it is still impossible
to reach at least 1.5 bar, disengage com-
pressor from valve and current outlet,
then move the car forth for approx. ten
metres in order to distribute the seal-
ing fluid inside the tyre evenly, then re-
peat the inflation operation;
❒If after this operation it is still impossi-
ble after 5 minutes to reach at least 1.8
bar, do not start driving since the tyre
is excessively damaged and the quick
tyre repair kit cannot guarantee suit-
able sealing, contact Fiat Dealership;
fig. 15F0C0515mfig. 16F0C0516m
Apply the sticker in a visible
position for the driver to in-
dicate that the tyre has been treat-
ed with the quick tyre repair kit. Dri-
ve carefully especially when corner-
ing. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNING
❒after driving for about 10 minutes stop
and check again the tyre pressure; pull
up the handbrake;
If the pressure falls below 1.8
bars, do not drive any fur-
ther: the quick tyre repair kit Fix & Go
automatic cannot guarantee proper
hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
❒If reaching the tyre pressure specified
in paragraph “Cold tyre inflation pres-
sure” in section “Technical Specifica-
tions”, start driving immediately;

181
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that
the corresponding fuse is intact before
changing a bulb. For the location of fus-
es, refer to the paragraph “If a fuse
blows” in this section;
❒ Before changing a bulb check the con-
tacts for oxidation;
❒Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒ Always check the height of the head-
light beam after changing a bulb.Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent bulb
is touched with the fingers, its
lighting intensity is reduced and life of
the bulb may be compromised. If
touched accidentally, rub the bulb with
a cloth moistened with alcohol and al-
low to dry.
Modifications or repairs to
the electrical system (elec-
tronic control units) carried out in-
correctly and without bearing the fea-
tures of the system in mind can cause
malfunctions with the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas which, if broken,
may cause small fragments of glass to
be projected outwards.
WARNING
Due to high voltage, the bulb
of (Xenon) gas-discharge
headlights must only be replaced by
experts: danger of death! Contact Fi-
at Dealership.
WARNING
IMPORTANT The headlight inner surface
may be lightly misted over: this is not a
fault but a natural fact due to low tem-
perature and the level of air humidity. It
will disappear as soon the headlights are
turned on. The presence of drops inside
the headlights means water infiltration,
therefore contact Fiat Dealership.

183
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
E
D
D
F
A
E
B
A
B
B
B
B
B
B
B
A
B
B
A
C
A
C
C
C
A
CH1
H7
H7
D2R
W5W
H1
PY21W
WY5W
P21W
W5W
P4/21W
P21/5W
P21W
R5W
P21W
W2,3W
P21W
P21W
W5W
C5W
W5W
C5W
C10W
C5W
W5W
C5W55W
55W
55W
35W
5W
55W
21W
5W
21W
5W
4W/21W
21W/5W
21W
5W
21W
2,3W
21W
21W
5W
5W
5W
5W
10W
5W
5W
5W
Bulbs Figure 19 Type Power
Main beam headlights
Longlife dipped beam headlights
Dipped beam headlights
Gas-discharge low beam headlights (where provided)
Front sidelights (2 per headlight) longlife
Front fog lights (where provided)
Front direction indicators
Side direction indicators
Rear direction indicators
Taillights (3-door versions)
Taillights/Rear fog lights (5-door versions)
Taillights/Brake lights
(Multi Wagon versions)
Taillights (Multi Wagon versions)
(side fixed light unit)
Taillights (Multi Wagon versions)
(tailgate light unit)
Brake lights (3-door versions)
Third brake light (additional brake light)
Reversing light
Rear fog lights
Number plate light (saloon versions)
Number plate light (Multi Wagon versions)
Puddle/door lights
Front roof light
Rear roof light (where provided)
Glovebox light
Boot light
Courtesy mirror light (where provided)

184
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IF AN EXTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT LIGHT UNITS
fig. 20-21
The front light units contain the sidelights,
dipped beam, main beam, direction indi-
cator and front fog light bulbs.
The bulbs are arranged inside the light unit
as follows:
Adirection indicators / fog lights (where
provided)/sidelights / dipped beam
headlights
Bsidelights / main beam headlights.To change the bulbs of the sidelights, di-
rection indicators, low beams and fog
lights it is necessary to remove the cover
Creleasing the catch D.
To change the bulbs of main beams and
sidelights, remove the cover Eoperating
the device F.
fig. 20F0C0435mfig. 21F0C0436m
After replacement, refit the
covers correctly checking that
they are properly secured.

186
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
DIRECTION INDICATORS
Front fig. 24
To change the bulb, proceed as follows:
❒remove the protective cover releasing
the catch;
❒turn the bulb holder Acounterclock-
wise and remove it;
❒remove the bulb Bpushing it gently and
turning counterclockwise;
❒replace the bulb and then refit the bulb
holder turning it clockwise, checking
that it is secured correctly;
❒refit the protective cover correctly.Side fig. 25
To change the bulb, proceed as follows:
❒push the transparent cover Atowards
car running direction to compress the
catch;
❒remove the unit;
❒turn the bulb holder Bcounterclock-
wise, remove the snap-fitted bulb Cand
replace it;
❒ refit the bulb holder Bin the transpar-
ent cover, then position the unit mak-
ing sure the catch clicks into place.FRONT FOG LIGHTS
(where provided) fig. 26
To change the bulb, proceed as follows:
❒remove the protective cover releasing
the catch;
❒release the bulb holder catch A;
❒disconnect the electric connector B;
❒remove the bulb Cand replace it;
❒fit the new bulb, making the tabs of the
metallic part coincide with the grooves
on the reflector, reconnect the electri-
cal connector Bthen hook the bulb
holder catch A;
❒refit the protective cover correctly.
fig. 24F0C0177mfig. 25F0C0212mfig. 26F0C0176m

187
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
FRONT SIDELIGHTS
To replace the bulbs proceed as follows:
❒remove the protective cover Aand C-
fig. 27releasing catch Band Dre-
spectively;
❒using the extension A-fig. 28or D-
fig. 29, turn the bulb holder B-fig. 28
or E-fig. 29clockwise and counter-
clockwise and then withdraw it;
❒remove the bulb C-fig. 28or F-fig. 29
and replace it;
❒refit the bulb holder making sure the
catch clicks into place; also check the
proper bulb positioning looking at the
lamp from outside;
❒refit the protective cover correctly.REAR LIGHT UNITS
(saloon versions)
To change the bulb, proceed as follows:
❒open the tailgate;
❒from inside the boot, withdraw the
connector A-fig. 30, loosen the 3 nuts
Bwith the extension (where provided)
used to tighten the wheel bolts (sup-
plied with the tool kit) and remove the
light unit.
IMPORTANT When subwoofer is locat-
ed on the left side of the boot, to replace
the rear light cluster contact Fiat Dealer-
ship.
fig. 27F0C0175mfig. 28F0C0180mfig. 29F0C0388m
fig. 30F0C0208m

188
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
3-door versions
To change the bulb, proceed as follows:
❒press lamp holder catches A-fig. 31
outwards and remove it;
❒remove bulbs slightly pushing them and
turning counterclockwise.The bulbs are arranged inside the light unit
as follows:
B: taillights;
C: direction indicators;
D: rear fog lights;
E: reversing lights;
F: taillights.
fig. 31F0C0181mfig. 32F0C0182m
5-door versions
To change the bulb, proceed as follows:
❒unloose the 4 screws A-fig. 32and re-
move the bulb holder;
❒ remove bulbs slightly pushing them and
turning counterclockwise.
The bulbs are arranged inside the light unit
as follows:
B: taillights;
C: direction indicators;
D: taillights/rear fog lights;
E: reversing lights.

189
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
REAR LIGHT UNITS
(Multi Wagon versions)
Tailgate light unit
To change the bulb, proceed as follows:
❒open the tailgate;
❒ push down cover A-fig. 33and re-
move electric connectorB-fig. 34;
fig. 33F0C0425m
❒push the bulb holder side tabs A-
fig. 35inwards to remove it;
❒ remove bulbs slightly pushing them and
turning counterclockwise.
fig. 34F0C0426mfig. 35F0C0417m
The bulbs are arranged inside the light unit
as follows:
B: taillights;
C: reversing lights;
D: rear fog lights.

190
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
fig. 36F0C0360mfig. 37F0C0361mfig. 38F0C0419m
Side fixed light unit
To change the bulb, proceed as follows:
❒open the tailgate;
❒turn the handle A-fig. 36to open the
door B;
❒hold the tongue C-fig. 37and open the
door for the rear light unit access;
❒remove the electric connector D;
❒push the bulb holder side tabs A-
fig. 38inwards to remove it;
❒ remove bulbs slightly pushing them and
turning counterclockwise.The bulbs are arranged inside the light unit
as follows:
B: taillights/brake lights;
C: direction indicators.

191
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
ADDITIONAL BRAKING LIGHT
(THIRD STOP)
IMPORTANT To replace the additional
braking lights (third stop) contact a Fiat
Dealership.
NUMBER PLATE LIGHTS
Saloon versions fig. 39
To change the bulb, proceed as follows:
❒work in the points shown by the arrow
and slacken the 2 cover fastening
screws A;
❒change the bulb Breleasing it from the
side contacts and making sure the new
bulb is correctly fastened between the
contacts;
❒refit the cover.
fig. 39F0C0411mfig. 40F0C0367m
Multi Wagon versions fig. 40
To change the bulb, proceed as follows:
❒use the screwdriver supplied with the
car to remove the transparent cover A
as shown in the figure;
❒change the bulb Breleasing it from the
side contacts and making sure the new
bulb is correctly fastened between the
contacts;
❒refit the transparent cover.