fuse FIAT STILO 2006 1.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2006, Model line: STILO, Model: FIAT STILO 2006 1.GPages: 274, PDF Size: 4.76 MB
Page 18 of 274
17
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
ALARM
(where provided)
The alarm function is provided in addition
to all remote control functions previous-
ly described and it is controlled by the re-
ceiver located under the dashboard, next
to the fuse box.
WHEN THE ALARM IS
TRIGGERED
The alarm comes into action in the fol-
lowing cases:
❒ unlawful opening of one of the doors,
bonnet or boot (perimetral protec-
tion);
❒attempt to start the engine (turning the
ignition key to MAR);
❒ battery cable cutting;
❒ presence of moving bodies in the pas-
senger’s compartment (volumetric pro-
tection);
❒ abnormal raising/sloping of the car. Depending on the markets, the cutting in
of the alarm causes operation of the siren
and direction indicators (for about 26 sec-
onds). The ways of operating and the num-
ber of cycles may vary depending on the
markets.
A maximum number of sound/sight cycles
is however envisaged.
Volumetric and anti-raising protections
can be cut off by operating the front ceil-
ing light controls (see paragraphs “Volu-
metric protection sensors” and “Anti-rais-
ing sensor” on the following pages).
IMPORTANT The engine immobiliser
function is guaranteed by the Fiat CODE
system, which is automatically activated
when the ignition key is removed.HOW TO ACTIVATE THE
ALARM
With the doors, bonnet and boot shut and
the ignition key in the STOPposition or
with the key removed, point the key with
remote control in the direction of the car,
then press and release the button
Á.
With the exception of certain markets,
the system sounds a “beep” and the doors
are locked.
Engagement of the alarm is preceded by
a self-diagnostic test. If a fault is detected
the system sounds a further warning
“beep” and the display shows the relevant
message (see section “Warning lights and
messages”).
In this case, switch the alarm system off by
pressing button
Ë, check that the doors,
bonnet and tailgate are properly shut, then
switch the alarm on again by pressing but-
ton
Á.
Otherwise, the door, bonnet or tailgate
that is not shut properly will be excluded
from the alarm system control.
Page 67 of 274
66
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DEVICE DISENGAGEMENT
Turn the knurled ring A-fig. 56to OFF
or the ignition key to STOP. The device
is automatically deactivated also in one of
the following cases:
❒pressing the brake or clutch pedal;
❒ASR or ESP cut-in (where provided);
❒gearshifting in versions with Selespeed
automatic transmission (where provid-
ed);
❒involuntarily moving the Selespeed
lever (where provided) toN.
When travelling with the de-
vice on, never set the
gearshift lever to neutral and do not
move the Selespeed lever to N.
WARNING
In the event of device mal-
function or failure, turn the
knurled ring A-fig. 56to OFF and
contact a Fiat Dealership after check-
ing the protection fuse integrity.
WARNING
Page 78 of 274
77
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SUNROOF OPENING/CLOSING
With key without remote control
(where provided)
Opening: turn the key clockwise in the
door revolving plug.
Closing: turn the key counterclockwise in
the door revolving plug.
With key with remote control
Opening: prolonged pressing (for more
than 2 seconds) on button
Ë.
Closing: prolonged pressing (for more
than 2 seconds) on button
Á.
When buttons
Á/Ë, are released, the
above functions are cut-off.
When opening, blades and curtain open at
the same time.
When closing, the curtain closes first and
then are closed the blades.ANTI-CRUSHING SAFETY
SYSTEM
The anti-crushing safety system fitted on
the front curtain outline is active along the
whole closing range of the curtain and cuts
into operation when an obstacle (e.g.: fin-
ger, hand, etc...) is met. This safety device
guarantees the reversal for a short sec-
tion.
In addition, the anti-crushing safety system
is active on the rear border of the first
blade and on the front outline of the sec-
ond blade: in this case it is active on the
whole closing range of the curtain and cuts
into operation when an obstacle (e.g.: fin-
ger, hand, etc...) is met. This safety device
guarantees the reversal for a short sec-
tion.
As concerns the first blade it is active on
the whole rotation range and guarantees
the reversal of the whole stroke.
After anti-crushing system activation, re-
setting can be carried out with the fol-
lowing 2 procedures:
❒pushing knob A-fig. 83upwards (reset
previously stopped movement);
❒turning knob Ato another position.INITIALISATION PROCEDURE
Sunroof shall be re-initialised after dis-
connecting the battery or if the relevant
protection fuse is blown:
❒turn knob A-fig. 81to “0” (fully
closed);
❒keep the knob pressed for over 5 sec-
onds: the sunroof will close jerkily;
❒keep the knob pressed and wait for
complete closing of the sunroof, until
the sun curtain clicks twice.
Sunroof is now initialised and it shall work
regularly. Otherwise, contact Fiat Deal-
ership.
IMPORTANT Carry out the initialisation
procedure with the engine running. If stop-
ping the initialisation procedure before
ending it, repeat it from the beginning.
Page 104 of 274
103
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
PARKING SENSORS
(where provided)
Parking sensors are located in the rear
bumper fig. 126(saloon versions) and
fig. 127 (Multi Wagon versions) and their
function is to inform the driver, through
an intermittent buzzer, about the pres-
ence of obstacles behind the car.
ACTIVATION
Sensors are automatically activated when
the reverse gear is engaged.
As the distance from the obstacle behind
the car decreases, the acoustic alarm be-
comes more frequent.
BUZZER WARNINGS
When the reverse gear is engaged an in-
termittent acoustic signal is automatically
activated.
The acoustic signal:
❒becomes louder as the reduction of dis-
tance between the car and the obstacle
decreases;
❒becomes continuous when the distance
between the car and the obstacle is less
that 30 cm and stops immediately if the
distance raises.
❒is constant if the distance is unvaried.
If this situation takes place for side sen-
sors, the signal is stopped after about 3
seconds to prevent sound indications
when performing manoeuvres near
walls.
It is absolutely forbidden to
carry out whatever after-
market operation involving steering
system or steering column modifica-
tions (e.g.: installation of anti-theft
device) that could badly affect per-
formance and safety, cause the lapse
of warranty and also result in non-
compliance of the car with homolo-
gation requirements.
WARNING
Always switch the engine off,
remove the key from the
starting device and actuate the steer-
ing lock before carrying out any main-
tenance operation, especially when
the wheels are raised from the
ground. In case this is not possible
(e.g. when the key must be in MAR
position or the engine running), re-
move the electric power steering
main fuse before carrying out any
maintenance operation.
WARNING
fig. 126F0C0301m
fig. 127F0C0364m
Page 168 of 274
167
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR PROTECTION
SYSTEM FAILURE-FIAT
CODE (amber)
ALARM FAILURE
(where provided) (amber)
BREAK-IN ATTEMPT
(amber)
Car protection system failure
Turning the key to MARthe warning light
shall flash only once and then go off.
The turning on of the warning light glow-
ing steadily, with the ignition key at MAR,
indicates a probable failure (see “Fiat Code
system” in section “Dashboard and con-
trols”).
IMPORTANT The turning on at the same
time of the
Uand Ywarning lights in-
dicates a failure of the Fiat CODE system.
If with the engine running the warning light
Yflashes (together with the message on
the display), this means that the car is not
protected by the engine immobilising de-
vice (see “Fiat Code system” in section
“Dashboard and controls”). Contact Fiat
Dealership to have all the keys memo-
rised.Alarm failure (where provided)
The turning on of the warning light indi-
cates a failure in the alarm system. Con-
tact Fiat Dealership as soon as possible.
The display will show the dedicated mes-
sage.
Break-in attempt
The turning on of the warning light indi-
cates an attempt of break-in. Contact Fi-
at Dealership as soon as possible.
The display will show the dedicated mes-
sage.EXTERNAL LIGHT
FAILURE (amber)
The warning light turns on
when one of the following lights
is failing:
❒side/taillights
❒brake lights or relevant fuse
❒rear fog lights
❒direction indicators
❒number plate lights.
The failure referring to these lights could
be: one or more blown bulbs, a blown
protection fuse or an electric connection
cut-off.
The display will show the dedicated mes-
sage.
YW
REAR FOG LIGHTS
(amber)
The warning light turns on
when the rear fog lights are
turned on.
4
FRONT FOG LIGHTS
(green)
The warning light turns on
when the front fog lights are
turned on.
5
Page 170 of 274
169
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
ENGINE STARTING.............................................................. 170
IF A TYRE IS PUNCTURED ................................................ 171
QUICK TYRE REPAIR KIT FIX & GO automatic ......... 177
WHEN NEEDING TO CHANGE A BULB .................... 181
IF AN EXTERIOR LIGHT BURNS OUT .......................... 184
IF AN INTERIOR LIGHT BURNS OUT ........................... 192
IF A FUSE BLOWS ................................................................. 196
IF THE BATTERY IS FLAT ................................................... 205
JACKING THE CAR .............................................................. 206
TOWING THE CAR ............................................................ 206
FIRE EXTINGUISHER ........................................................... 208
I I
N N
A A
N N
E E
M M
E E
R R
G G
E E
N N
C C
Y Y
Page 182 of 274
181
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that
the corresponding fuse is intact before
changing a bulb. For the location of fus-
es, refer to the paragraph “If a fuse
blows” in this section;
❒ Before changing a bulb check the con-
tacts for oxidation;
❒Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒ Always check the height of the head-
light beam after changing a bulb.Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent bulb
is touched with the fingers, its
lighting intensity is reduced and life of
the bulb may be compromised. If
touched accidentally, rub the bulb with
a cloth moistened with alcohol and al-
low to dry.
Modifications or repairs to
the electrical system (elec-
tronic control units) carried out in-
correctly and without bearing the fea-
tures of the system in mind can cause
malfunctions with the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas which, if broken,
may cause small fragments of glass to
be projected outwards.
WARNING
Due to high voltage, the bulb
of (Xenon) gas-discharge
headlights must only be replaced by
experts: danger of death! Contact Fi-
at Dealership.
WARNING
IMPORTANT The headlight inner surface
may be lightly misted over: this is not a
fault but a natural fact due to low tem-
perature and the level of air humidity. It
will disappear as soon the headlights are
turned on. The presence of drops inside
the headlights means water infiltration,
therefore contact Fiat Dealership.
Page 197 of 274
196
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
If a general fuse (MEGA-
FUSE, MIDI-FUSE, MAXI-
FUSE) cuts in, do not attempt any re-
pair and contact a Fiat Dealership.
Before replacing a fuse, make sure
the ignition key has been removed
and that all the other services are
switched off and/or disengaged.
WARNING
If a fuse blows again, contact
a Fiat Dealership.
WARNING
IF A FUSE BLOWS
GENERAL
The fuse is a protective device for the
electric system: it comes into action (i.e.
it cuts off) mainly due to a fault or im-
proper action on the system.
When a device does not work, check the
efficiency of its fuse: the conductor ele-
ment A- fig. 55must be intact. If not, re-
place the fuse with one of the same amp
rating (same colour).
B: undamaged fuse
C: fuse with damaged filament.
To replace a fuse, use the pliers Dhooked
to the fusebox on the dashboard.Never replace a fuse with
metal wires or anything else.
fig. 55F0C0220m
Never replace a fuse with
another with a higher amp
rating, DANGER OF FIRE.
WARNING
Page 198 of 274
197
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
FUSE LOCATION
Fuses are grouped into four fuse boxes, to
be found respectively on the dashboard,
on the battery positive pole, next to the
battery and in the boot (left-hand side).
Certain versions are also fitted with a sin-
gle fuse set inside the engine compartment
fuse box.
fig. 57F0C0266m
fig. 56F0C0193m
Fuse box on the dashboard fig. 57
To gain access to the fuses in the fuse box
on the dashboard, open lid A-fig. 56.
Page 199 of 274
198
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Fuse box next to the battery fig. 59
To gain access to the fuse box and to the
single fuse next to the battery, press the
retainers A-fig. 58and remove the pro-
tection cover B.
fig. 59F0C0151m
fig. 58F0C0498m