reset FIAT ULYSSE 2009 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2009, Model line: ULYSSE, Model: FIAT ULYSSE 2009 2.GPages: 254, PDF Size: 3.56 MB
Page 38 of 254
GETTING TO KNOW YOUR CAR
37
Remember that in the
case of a violent collision,
back seat passengers not
wearing seat belts, in addition to
being personally exposed to se-
rious risk, also represent a seri-
ous danger to the passengers in
the front.
Make the height adjust-
ment when the car is sta-
tionary. ADJUSTING SEAT BELT
HEIGHT fig. 57Always adjust the height of the seat
belt to fit the person wearing it. This
could greatly reduce the risk of injury
in the case of collision. The belt is ad-
justed properly when the webbing
passes approximately halfway between
the edge of the shoulder and the neck.
Correct adjustment is obtained when
the belt passes half way between the
end of the shoulder and the neck.
Three height adjustment are possi-
ble.
To adjust, press button A(as shown
by the arrows) and raise or lower the
grip.After you have made the
adjustment, always make
sure that the loop is at-
tached firmly in one of the fixed
positions and cannot move. To
do this, with the button released,
exert a further pressure to allow
the anchor device to catch if re-
lease did not take place at one of
the preset positions.
fig. 57
F0B0230b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 37
Page 48 of 254
GETTING TO KNOW YOUR CAR
47
The seat fitted with child restraint
system shall be set in the most back-
ward position.
You are recommended to choose
Kiddy Isofix since this seat has been
designed and tested specifically for this
vehicle. Kiddy Isofix has been type ap-
proved according to the European
Standard ECE-R44/03.
Type Isofix restraint systems are fas-
tened to two metal brackets A-fig.
70, between the seat back and the
cushion. 3)Keep to the instructions for fas-
tening the specific child restraint sys-
tem you are using which must be pro-
vided by the manufacturer. Keep the
child restraint system installation in-
structions with the vehicle documents
and the Handbook. Never use a child
restraint system without installation
instructions.
4)Always check that the seat belt is
well fastened by pulling the webbing.
5)Only one child can be secured to
a child restraint at a time. Never car-
ry two children in one restraint system.
6)Always check that the seat belts
are not positioned on the child’s
throat.
7)While travelling, do not let the
child seat incorrectly or release the
belts.
8)Passengers should never carry
children or babies on their laps. No-
one, however strong they are, can
hold a child in the event of a crash.
9) In case of an accident, replace the
seat with a new one.Presetting for mounting the
“Type Isofix” child restraint
system
The car is equipped for Type Isofix
child restraint system installation. Type
Isofix is a new European unified sys-
tem to carry children on the seats
which does not prevent using tradi-
tional child restraint systems. This sys-
tem must be fastened using the ap-
propriate brackets set on the car.
Mixed fitting is possible, with a tra-
ditional child restraint system on the
left and an Type Isofix restraint system
on the right. Being their size different,
it is possible to fit on the seats up to
a maximum of three traditional child
restraint systems, while only two Isofix
restraint systems can be attached to
the fasteners.
Lineaccessori Fiat includes Kiddy
Isofix restraint system for children
weighing up to 18 kg with the child
seat placed in the driving direction and
up to 13 kg with the child seat placed
in the opposite direction (groups 0,
0+and 1).
fig. 70
F0B0235b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 47
Page 49 of 254
GETTING TO KNOW YOUR CAR
48
Mount the child re-
straint system only with
the car stationary. The
Isofix child restraint system is
properly anchored to the mount-
ing brackets when clicks are
heard. In any case, keep to the in-
stallation instructions that must
be provided by the child restraint
system’s Manufacturer.The Kiddy Type Isofix seat can how-
ever be fitted to the front passenger
seat even if not provided with Isofix
mounts: in this case, the child’s seat
must be fastened by means of the
three-anchoring point seat belt both
in the ahead and backward positions
The Type Isofix child’s seat covers
three weight groups: 0, 0+and 1.
Fitting the seat for the 0
and 0+ group fig. 71
For children included in groups 0and
0+, the restraint system faces back
(for children with weight up to 13 kg)
and the child is held by the restraint
system belts D.
Proceed as follows to fit the child re-
straint system in the correct way:
– the release lever Bmust be at rest
position (inward);
– find the presetting brackets A, then
position the child restraint system with
the fastening devices Caligned with
the brackets;– push the child restraint system un-
til hearing the locking clicks;
– check proper locking by moving
the child’s seat with force: the built-
in safety mechanism actually inhibit im-
proper coupling with only one cou-
pling locked.
fig. 71
F0B0237b
The Kiddy Isofix seat
shall not be fitted on third
row rear side seats.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 48
Page 50 of 254
GETTING TO KNOW YOUR CAR
49
As the child grows, passing to the
next weight group (group 1) the child
safety chair must be fitted in the ahead
direction; perform this operation by
following the instructions provided by
the child seat’s Manufacturer.
With the child’s seat in this position,
adjust the corresponding front seat in
such a way that the Kiddy Isofix seat
structure leans against the front seat
backrest.
Fitting the seat for group 1
fig. 72-73
For proper mounting proceed as fol-
lows:
– check whether the release lever B
is at rest position (inward);
– find the presetting brackets A, then
position the child restraint system with
the fastening devices Caligned with
the brackets;
– push the child restraint system un-
til hearing the locking clicks;With the child seat in this position,
the corresponding front seat must be
positioned halfway the sliding guides
travel, with the backrest in vertical po-
sition.
fig. 73
F0B0238b
– for seats positioned facing the run-
ning direction, fasten the upper belt (in
the upper seat pocket) to the ring A-
fig. 72located on the floor immedi-
ately behind the seat:
– check proper locking by moving
the child’s seat with force: the built-
in safety mechanism actually inhibit im-
proper coupling with only one cou-
pling locked.
With this configuration, the child is
secured also by the car seat belts
fig. 73and by the upper belt.
Keep to the instructions provided by
the child restraint system Manufac-
turer for fastening the specific child re-
straint system you are using.
fig. 72
F0B0236b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 49
Page 51 of 254
GETTING TO KNOW YOUR CAR
50
INSTRUMENTSA -Odometer display: speedometer,
kilometre counter, maintenance indi-
cator, engine oil level gauge (for ver-
sions/markets, where provided) and,
for versions with automatic gear, en-
gaged gear indicator and symbol for
presence of ice on the road, if any.
B -Warning lights
C -Trip kilometre counter reset
button
D -Button for instrument panel
brightness adjustment
fig. 74F0B0412b
fig. 75F0B0413b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 50
Page 54 of 254
GETTING TO KNOW YOUR CAR
53
tion, distance covered, average con-
sumption, average speed, distance to
destination; to display also info con-
cerning: automatic light turning on,
ESP, rain sensor.
To reset the trip computer data,
keep pressed the button set at the end
of the right stalk fig. 79b;
– Personal/set-up menu: to acti-
vate/deactivate electric rear wheel
lock, to activate/deactivate rear win-
dow wiper, to activate/deactivate au-
tomatic light turning on and to set
date, clock, display brightness, units
and language.
MULTIFUNCTION DISPLAY
(with infotelematic Connect /
Connect Nav+ system)
CONTROLS fig. 79c
A– button for opening the main
menu
B– buttons for surfing the main
menu
C– button for confirming the se-
lected function or for confirming set
values
D– button for canceling the function
/ going back to previous screenE– button for selecting the type of
information displayed on the right side
of the screen (date, radio – CD, trip
computer)
Main menu
Press button Ato open the main
menu and to display the following
functions:
– Navigation
– Audio
– Trip computer: to display info
concerning: range, instant consump-
tion, distance covered, average con-
sumption, average speed, distance to
destination; to display also info con-cerning: automatic light turning on,
ESP, rain sensor.
To reset the trip computer data,
keep pressed the button set at the end
of the right stalk fig. 79b;
– Address book
– Personal/set-up menu: to acti-
vate/deactivate electric rear wheel
lock, to activate/deactivate rear win-
dow wiper, to activate/deactivate au-
tomatic light turning on and to set
date, clock, display brightness, units
and language.
– Map
– Video
For Navigation, Audio, Address
book, Telematic, Map and Video func-
tions, refer to the attached “Connect
Nav+” Supplement.
fig. 79b
F0B0435b
fig. 79c
F0B0452b
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 53
Page 55 of 254
GETTING TO KNOW YOUR CAR
54
ODOMETER DISPLAY
This instrument displays the follow-
ing values:
on the upper line:partial kilome-
tres and engine oil level gauge (for ver-
sions/markets, where provided)
on the lower line:total kilometres
and programmed maintenance indica-
tor; versions with automatic gear are
also fitted with engaged gear indicator
(for further details see the chapter
“Automatic gear”).
Trip kilometre counter fig. 80
Press button Ato display the trip
kilometres. Keep it pressed to reset.Engine oil level gauge
(for versions/markets, where provided)
After turning the ignition key to M,
this indicator first displays the kilo-
metres to be reached before carrying
out the next maintenance operation
and then displays the engine oil level
in the engine sump for a limited time.
Fig. 81shows the correct oil level
condition. Flashing of the wording
“OIL”, together with the sound of the
buzzer and the dedicated message in-
dicate low engine oil level. Flashing of
wording “OIL –“ indicates an engine
oil level sensor failure.
fig. 80
F0B0244b
fig. 81
F0B0415b
fig. 82
F0B0246b
Scheduled maintenance
indicator fig. 82
The maintenance indicator uses
warning lamp Aand kilometre
counter Bto indicate when oil and oil
filter are to be replaced in accordance
with the service schedule. To keep the
warranty valid, go to a Fiat Dealer-
ship(see also the “Car maintenance”
chapter).
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 54
Page 56 of 254
GETTING TO KNOW YOUR CAR
55
IMPORTANTAny anomalies
should be reported to your Fiat
Dealershipimmediately without
waiting for the next servicing coupon
to be carried out.
A- Maintenance warning lamp.
B- Kilometre counter.
C- Configuration and reset button.
O
PERATION
When the key is turned to M, warn-
ing lamp Awill light up for some sec-
onds and the kilometre counter Bwill
display the number of kilometres
(rounded down) still to be travelled
before the next servicing is due. Af-
ter this period the engine oil level (for
versions/markets, where provided)
will be automatically displayed and
then the total kilometres travelled will
be displayed as well;
– maintenance due after 2000
km until the maintenance dead-
line: when the key is turned to M,
warning lamp Awill light up and the
kilometre counter Bwill display the
number of kilometres (rounded
down) still to be travelled before the
next servicing is due. After some sec-onds the warning lamp will remain lit
and the total travelled kilometres will
be displayed;
– maintenance overdue: when
the key is turned to M, warning lamp
Awill flash for some seconds and the
number of kilometres over the main-
tenance limit will be displayed; after
this period the warning lamp will re-
main lit and the total travelled kilo-
metres will be displayed.
IMPORTANTIf, after about
12 months, the kilometres indicated in
the Service Schedule have not been
reached yet, when the key is turned to
M, warning lamp Awill light up and
the kilometre counter will show 0 km.
In this case contact a Fiat Dealer-
ship.
C
ONFIGURATION PROCEDURE
If the vehicle is used in particularly
difficult conditions, you are recom-
mended to reset the system and re-
duce the maintenance frequency from
30,000 to 20,000 km.
To alter the maintenance frequency:
– turn the key to M;– press button Cand keep it
pressed, so the number of kilometres
still remaining or already passed since
the scheduled servicing will flash;
– release the button immediately to
display the preset maintenance fre-
quency;
– a repeated press on button C will
change the maintenance frequency to
the one required:
30,000 km(recommended in nor-
mal use conditions);
20,000 km(recommended in se-
vere use conditions);
– when the selected maintenance fre-
quency is displayed, press button Cfor
10 seconds (the maintenance fre-
quency selected will flash for 10 sec-
onds);
– release the button to confirm as
soon as the display stops flashing.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 55
Page 57 of 254
GETTING TO KNOW YOUR CAR
56
The navigation system
helps the driver while dri-
ving by suggesting, vocal-
ly and graphically, the best route
to be followed to reach the pre-
set destination. The suggestions
given by the navigation system do
not exempt the driver from fully
responsibility due to driving be-
haviour and compliance with
road and other traffic regulations.
The responsibility for road safety
always and anyway lies with the
vehicle’s driver.RESETTING
To reset the maintenance indicator:
– turn the ignition key to S;
– press and keep button Cpressed;
– turn the key to M;
– press and keep button Cpressed
for around 10 seconds so that the
maintenance indicator starts progres-
sive resetting until = 0 will be dis-
played;
– release button C and warning lamp
Awill go off to confirm successful re-
setting.
Your Fiat Dealership will reset
the maintenance indicator after
each control carried out.
INFOTELEMATIC
CONNECT SYSTEM
(for versions/markets, where provided)
The vehicle can be fitted with the in-
fotelematic CONNECT system which
includes a radio with CD-ROM/Audio
player, GSM cell phone, navigator and
on-board computer, designed in ac-
cordance with the specific features of
the passenger compartment and with
a personalised design that blends with
the styling of the dashboard.
The system is installed in an user-
friendly position for the driver and the
graphics on the front panel make it
easy to quickly locate the controls
which facilitate the use of them.
To use the system keep to the
instructions and warnings con-
cerning both its functions and the
relative road safety rules con-
tained in the specific Annex pro-
vided with the present Owner
Handbook.
001-077 ULYSSE ING:001-077 ULYSSE ING 5-11-2009 12:11 Pagina 56
Page 86 of 254
GETTING TO KNOW YOUR CAR
85
Rear window wiper fig. 103
This feature can only work with the
ignition key at M.
– Turn knurled knob Afrom 0to
'.
When the windscreen wiper is
working and the reverse gear is en-
gaged, the rear window wiper is au-
tomatically turned on to improve rear
visibility.Rear window washer fig. 104
This feature can only work with the
ignition key at M.
– Turn knurled knob Afrom
'to
&(temporary position) and a jet of
rear window washer fluid is sent to
the rear window.
At the same time, the rear window
wiper will flick wipe thrice.
fig. 103
F0B0427b
fig. 104
F0B0428b
fig. 105
F0B0269b
TRIP COMPUTER
The trip computer is device for dis-
playing the following information by
pressing repeatedly button A-fig. 105
on the stalk edge:
range, current fuel consump-
tion, distance from destination,
trip 1 (kilometres travelled, av-
erage consumption, average
speed) etrip 2 (kilometres trav-
elled, average consumption, av-
erage speed).
This information will be viewed on
the infotelematic CONNECT system
display.
Reset: press and keep button A
pressed for more than 2 seconds.
078-135 ULYSSE ING 10-03-2009 11:39 Pagina 85