oil FORD ASPIRE 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: ASPIRE, Model: FORD ASPIRE 1996 1.GPages: 268, PDF Size: 2.2 MB
Page 10 of 268
7
applicability of such laws and regulations to
your intended use for the vehicle, and to
arrange for the installation of required
equipment. Your Ford dealer has information
about the availability of many items of
equipment which may be ordered for your
vehicle.
*
[IN06000(ALL)01/95]
Breaking Your Vehicle In
*
[IN06100(ALL)03/95]
Your new vehicle goes through an adjustment or
break-in period during the first 1,000 miles
(1,600 km) that you drive it. During the break-in
period, you need to pay careful attention to how
you drive your vehicle.
%*
[IN06300(ALL)01/95]
q
Avoid sudden stops.Because your vehicle
has new brake linings, you should take these
steps:
*
[IN06400(ALL)01/95]
Ð Watch traffic carefully so that you can
anticipate when to stop.
*
[IN06500(ALL)01/95]
Ð Begin braking well in advance.
*
[IN06600(ALL)01/95]
Ð Apply the brakes gradually.
*
[IN06700(ALL)01/95]
The break-in period for new brake linings
lasts for 100 miles (160 km) of city driving or
1,000 miles (1,600 km) of highway driving.
%*
[IN06800(ALL)01/95]
q
Use only the type of engine oil that Ford
recommends.SeeEngine oil recommendations
in the Index. Do not use special ªbreak-inº
oils.
File:02icinf.ex
Update:Wed Jan 24 14:28:18 1996
Page 12 of 268
9
*
[IN08200(ALL)04/95]
Cleaning Chrome and Aluminum Parts
[IN08300(ALL)05/95]
Wash chrome and aluminum parts with a mild
detergent. Do not use steel wool, abrasive
cleaners, fuel or strong detergents.
*
[IN08400(ALL)04/95]
Cleaning Plastic Parts
*
[IN08500(ALL)04/95]
Some of your vehicle's exterior trim parts are
plastic. Clean with a tar and road oil remover if
necessary. Use a vinyl cleaner for routine
cleaning.
*
[IN08600(ALL)04/95]
Do not clean plastic parts with thinners, solvents
or petroleum-based cleaners.
%*
[IN08700(ALL)04/95]
If you have your vehicle rustproofed, remove
oversprayed rustproofing with a tar and road oil
remover. If rustproofing is not removed from
plastic and rubber parts, it can cause
deterioration.
File:02icinf.ex
Update:Wed Jan 24 14:28:18 1996
Page 63 of 268
61
*
[LG03615(ALL)02/95]
Engine Oil Pressure Warning Light
[LG03715(ALL)07/93]
This light indicates low oil pressure, not low oil
level. However, if the engine's oil level is low, it
could affect the oil pressure. This light comes on
every time the ignition key is turned to ON or
START, but it normally turns off when the
engine starts.
[LG03800(ALL)05/93]
one inch art:0030173-C
Engine oil pressure light
[LG03900(ALL)02/95]
If the light stays on or turns on while the engine
is running:
*
[LG04000(ALL)03/95]
1. Pull off the road as soon as safely possible.
[LG04100(ALL)03/94]
2.Shut off the engine immediately.Continued
operation could cause severe engine damage.
[LG04200(ALL)02/95]
3. Check the engine oil level. Make sure the car
is on level ground.
[LG04300(ALL)07/93]
4. Add oil to the full mark on the dipstick
before you drive your car again. Do not
overfill. Do not operate the engine when the
oil light is on. For more information about
adding oil, seeEngine oil recommendationsin
the Index.
[LG04350(ALL)05/95]
RWARNING
Do not rely on the oil light to tell you
when the oil is low. Have the oil checked
often. It is possible for damage to occur if
an engine is operated with a low oil level.
File:05iclgf.ex
Update:Wed Jan 24 14:32:51 1996
Page 138 of 268
138
*
[RE01010(ALL)07/95]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[RE01100(ALL)06/95]
RWARNING
Do not push-start your vehicle. You could
damage the catalytic converter. For further
information, seeJumper Cablesin the
Index.
*
[RE01200(ALL)03/95]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
*
[RE01300(ALL)03/95]
Preparing Your Vehicle
*
[RE01400(ALL)03/95]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
*
[RE01500(ALL)03/95]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[RE01600(ALL)04/95]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
File:12icref.ex
Update:Wed Jan 24 14:52:09 1996
Page 186 of 268
187
*
[SV13600(ALL)03/95]
Engine Oil Recommendations
*
[SV13610(ALL)09/95]
We recommend using Motorcraft oil or an
equivalent oil meeting Ford Specification
WSS-MZC153-F and displaying the American
Petroleum Institute CERTIFICATION MARK on
the front of the container.
*
[SV13650(ALL)03/95]
one third page art:0060021-E
The API Certification Mark
*
[SV13670(ALL)01/95]
Neveruse:
*
[SV13680(ALL)01/95]
q
ªNon-Detergentº oils
*
[SV13690(ALL)04/95]
q
Oils labeled API SA, SB, SC, SD, SE, SF or SG
%*
[SV13700(ALL)01/95]
q
Additional engine oil additives, oil treatments
or engine treatments
%*
[SV13710(ALL)03/95]
Engine oils with anSAE 5W-30viscosity are
PREFERREDfor your vehicle. They provide the
best engine performance, fuel economy and
engine protection for all climates down to-15ÊF
(-25ÊC).
%*
[SV13750(ALL)03/95]
Synthetic engine oils which are CERTIFIED and
of the preferred viscosity may be used in your
engine. The engine oil and oil filter must still be
changed according to the maintenance schedule.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 187 of 268
188
*
[SV13775(ALL)01/95]
Checking and Adding Engine Oil
*
[SV13800(ALL)03/95]
Since the proper amount of engine oil is
important for safe engine operation, check the oil
using the dipstick each time you put fuel in
your vehicle. Remember the engine must be off,
the oil must be warm and the vehicle must be
parked on level ground.
*
[SV13900(ALL)04/95]
Checking the engine oil level:
*
[SV14000(ALL)02/95]
1. Turn the engine off after it has warmed up
and allow a few minutes for the engine oil
to drain back into the oil pan.
[SV14050(ALL)04/95]
2. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
or 1 (First).
*
[SV14100(ALL)02/95]
3. Open the hood. Protect yourself from engine
heat.
[SV14200(ALL)03/95]
4. Locate the dipstick (highlighted in yellow)
and carefully pull it out of the engine.
[SV14300(ALL)05/93]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
[SV14400(ALL)07/93]
quarter page art:0032227-B
Engine oil dipstick
[SV14500(ALL)02/95]
6. Carefully pull the dipstick out again. If the
oil level is at or below the ªLº line, add
engine oil as necessary. If the oil level is
beyond the letter ªFº, engine damage or
high oil consumption may occur and some
oil must be removed from the engine.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 188 of 268
189 [SV14550(ALL)12/93]
NOTE: The distance between the L (low) and
F (full) marks on the dipstick
represents 1.0 liter (1.06 U.S. qts and
0.88 Imp. qts).
*
[SV14600(ALL)01/95]
7. Put the dipstick back in and make sure it is
fully seated.
*
[SV14800(ALL)01/95]
It may be necessary to add some oil between oil
changes. Make sure you use a CERTIFIED
engine oil of the preferred viscosity. Your
vehicle's warranty coverage may not apply if
engine damage is caused by the use of improper
engine oil.
*
[SV15000(ALL)03/95]
Add engine oil through the oil filler cap
highlighted in yellow. To add oil, remove the
filler cap and use a funnel to pour oil into the
opening. Be careful not to overfill the engine.
Recheck the oil level after you finish adding oil.
*
[SV16300(ALL)06/95]
Changing the Engine Oil and the Oil Filter
*
[SV16400(ALL)04/95]
Change the engine oil and oil filterper the
following, whichever occurs first.
*
[SV16500(ALL)04/95]
one third page art:0060618-C
Oil change intervals
*
[SV16600(ALL)06/95]
Refer to theMaintenance Schedule and Record
booklet for additional information.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 189 of 268
190 [SV17250(ALL)05/95]NOTE: Always dispose of used automotive
fluids in a responsible manner. Follow
your community's standards for
disposing of these types of fluids. Call
your local recycling center to find out
about recycling automotive fluids.
*
[SV17275(ALL)06/95]
RWARNING
Continuous contact with USED motor oil
has caused cancer in laboratory mice.
*
[SV17280(ALL)07/95]
Protect your skin by washing with soap and
water.
*
[SV17300(ALL)03/95]
Engine Coolant
*
[SV17500(ALL)02/95]
Checking the engine coolant
[SV17550(ALL)05/95]
NOTE: Be sure to read and understand
Precautions When Servicing Your
Vehicleat the beginning of this chapter.
*
[SV17600(ALL)05/95]
RWARNING
The cooling fan is automatic and may
come on at any time. Always disconnect
the negative terminal of the battery before
working near the fan.
%*
[SV17800(ALL)02/95]
Your vehicle's coolant protects your engine from
overheating in the summer and from freezing in
the winter. Check the level of the coolant at least
once a month. Simply look at the engine coolant
reservoir located in the engine compartment. To
locate the reservoir, see the diagram of your
vehicle's engine underEngine Type,in this
chapter.
[SV18000(ALL)04/89]
q
If the engine is hot, the reservoir should be
filled with engine coolant to the FULL mark,
and the radiator should be full.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 206 of 268
207 %
*
[SV29530(ALL)04/95]
Cleaning the Wheels
*
[SV29535(ALL)05/95]
Wash the wheels with the same detergent you
use to wash your vehicle's body. Do not use
acid-based wheel cleaners, steel wool, abrasives,
fuel, or strong detergents. These substances will
damage protective coatings. Use tar and road oil
remover to remove grease and tar.
[SV29540(ALL)05/95]
NOTE: Before going to a car wash, find out if
the brushes are abrasive.
*
[SV29610(ALL)05/95]
Battery
*
[SV29612(ALL)02/95]
The Motorcraft maintenance-free battery does
not require additional water during its life of
service. The vents are part of the cover and
cannot be removed. For longer, trouble-free
operation, keep the top of the battery clean and
dry. Also, make certain the battery cables are
tightly fastened to the battery terminals.
*
[SV29614(ALL)02/95]
If you see any corrosion on the battery cables or
terminals, remove the cables from the terminal
and clean them both with a wire brush. You can
neutralize the acid with a solution of baking
soda and water. Reinstall the cables when you
are done cleaning them, and apply a small
quantity of grease to the top of each battery
terminal to help prevent corrosion.
*
[SV29616(ALL)07/95]
Battery replacement
[SV29620(ALL)09/93]
If the original equipment battery requires
replacement (under warranty), it may be
replaced by a Motorcraft Low-Maintenance
battery.
[SV29625(ALL)04/95]
The Low-Maintenance battery has removable
vent caps for checking the electrolyte level and
adding water, if necessary. The electrolyte level
should be checked at least every 24 months or
24,000 miles (40,000 km) in temperatures up to
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996
Page 208 of 268
209 %
*
[SV29665(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
*
[SV29670(ALL)07/95]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
%*
[SV29675(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
%*
[SV29690(ALL)06/95]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
*
[SV29700(ALL)03/01]
Automatic Transaxle Fluid
*
[SV29800(ALL)03/95]
Under normal circumstances, you do not need to
check the fluid level of the transaxle, since your
vehicle does not use up transaxle fluid. Refer to
theMaintenance Schedule and Recordbooklet for
replacement intervals. However, if the transaxle
is not working properly Ð for instance, the
transaxle may slip or shift slowly, or you may
notice some sign of fluid leakage Ð the fluid
level should be checked.
File:15icsvf.ex
Update:Wed Jan 24 14:56:41 1996