torque FORD BRONCO 1996 5.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: BRONCO, Model: FORD BRONCO 1996 5.GPages: 376, PDF Size: 3.04 MB
Page 10 of 376
7
equipment. Your Ford dealer has information
about the availability of many items of
equipment which may be ordered for your
vehicle.
*
[IN06000( ALL)01/95]
Breaking Your Vehicle In
*
[IN06100( ALL)03/95]
Your new vehicle goes through an adjustment or
break-in period during the first 1,000 miles
(1,600 km) that you drive it. During the break-in
period, you need to pay careful attention to how
you drive your vehicle.
%*
[IN06300( ALL)01/95]
q
Avoid sudden stops.Because your vehicle
has new brake linings, you should take these
steps:
*
[IN06400( ALL)01/95]
Ð Watch traffic carefully so that you can
anticipate when to stop.
*
[IN06500( ALL)01/95]
Ð Begin braking well in advance.
*
[IN06600( ALL)01/95]
Ð Apply the brakes gradually.
*
[IN06700( ALL)01/95]
The break-in period for new brake linings
lasts for 100 miles (160 km) of city driving or
1,000 miles (1,600 km) of highway driving.
*
[IN06750( ALL)12/93]
q
Wheel lug nuts must be retightened to proper
torque specifications at 500 miles/800 km of
new vehicle operation. Proper torque
specifications are provided in this guide. Also
retighten to proper torque specification at 500
miles/800 km after any wheel change or any
other time the wheel lug nuts have been
loosened.
%*
[IN06800(BEF )01/95]
q
Use only the type of engine oil that Ford
recommends.SeeEngine oil recommendations
in the Index. Do not use special ªbreak-inº
oils.
File:ltinb.ex
Update:Fri Jun 9 15:32:32 1995
Page 131 of 376
131
*
[FV31101(B F )05/95]
RWARNING
A seatback which is folded forward even
a small degree may not lock properly in
the event of a sudden stop or collision.
[FV43500(B )01/89]
Rear Flip Fold Seat
[FV43600(B )01/89]
To fold the seat forward:
[FV43700(B )01/89]
1. The seat back latch is at the lower rear right
hand side of the seat. Lift the latch handle to
unlock the seat back.
[FV43800(B )03/90]
2. Fold the seat back over the seat cushion
until it locks into place.
[FV43900(B )03/90]
3. Unlock the seat from the floor striker by
lifting the seat latch handle at the center rear
edge of the seat.
[FV44000(B )03/90]
4. Lift the seat and fold forward.
[FV44100(B )12/89]
To remove and reinstall the rear flip-fold
seat:
[FV44200(B )01/89]
1. Remove the torque rod by releasing it from
the right hand floor bracket (by pushing
forward and up).
[FV44300(B )01/89]
2. Remove the pin spring retainers and the pins
from both the floor brackets.
[FV44400(B )01/89]
3. Remove the seat assembly from your Bronco.
Reverse this procedure to install the rear
flip-fold seat.
[FV44500(B )05/90]
NOTE: It is important that you do not damage
the seat belt hardware while removing
or installing the rear flip-fold seat.
File:ltfvb.ex
Update:Fri Jun 9 15:28:41 1995
Page 176 of 376
176quickly when the vehicle is first driven and has
not reached normal operating temperature.
*
[DR08730( ALL)07/94]
The PCM also controls the transmission's Torque
Converter Clutch to further raise vehicle
performance and fuel economy. The Torque
Converter Clutch will engage when the
transmission operating temperature and other
conditions determined by the PCM have been
met. Engagement of the clutch may be noted as
a decrease in engine speed after an upshift has
completed or when the driver has depressed the
throttle while driving at a steady road speed.
[DR08740( ALL)04/95]
To help in troubleshooting, the PCM continually
performs self-tests on the electronic control
system and if any faults are detected, will store
them in memory. The Transmission Control
Indicator Light (TCIL), which is located on the
gearshift lever, may flash steadily if a
malfunction has been detected. If the TCIL is
flashing, contact your Ford dealer as soon as
possible. If this condition persists, damage to the
transmission could occur.
[DR08745( ALL)04/95]
NOTE: The word ªOFFº located on the end of
the gearshift lever is the transmission
control indicator light (TCIL).
*
[DR08750( ALL)01/95]
Putting Your Vehicle in Gear
*
[DR08800( ALL)03/94]
Your vehicle's gearshift is on the steering
column. The Transmission Control Switch and
indicator light are located on the end of the
gearshift lever. You can put the gearshift in any
of the several positions.
File:ltdrb.ex
Update:Fri Jun 9 15:26:57 1995
Page 248 of 376
249
*
[RE22300(BEF )01/95]
7. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration.
*
[RE22400(B )12/89]
quarter page art:0020312-B
Lug nut tightening sequence
*
[RE23400(BEF )05/95]
RWARNING
Use of wheels or lug nuts other than
original equipment could cause damage to
the wheel or mounting system and allow
the wheels to come off while the vehicle
is in motion.
*
[RE23500(BEF )01/95]
8. Replace any wheel covers, ornaments, or hub
caps that your vehicle has. Make sure that
they are screwed or snapped into place.
[RE23615(BEF )02/95]
9. Put the tire, jack, and wrench away. (Make
sure jack is securely fastened so it doesn't
rattle when you drive.) The carrier is
designed to hold the temporary spare which
comes with your vehicle. The stowage of a
full size tire in the spare tire carrier may
damage the tire or the vehicle. The flat full
size tire should be stowed securely in the
vehicle until it can be repaired.
*
[RE23700(BEF )01/95]
10. Unblock the wheels.
*
[RE23800(B )06/93]
Retighten the wheel lug nuts to the specified
torque at 500 miles (800 km) of new vehicle
operation and at intervals specified in the
Maintenance Schedule and Recordbooklet.
File:ltreb.ex
Update:Fri Jun 9 15:25:48 1995
Page 249 of 376
250
*
[RE24200( ALL)10/89]
Also retighten to the specified torque at 500
miles (800 km) of operation after any wheel
change or any time the lug nuts are loosened.
*
[RE24301( ALL)05/95]
RWARNING
Failure to retighten wheel lug nuts at
mileages specified could allow wheels to
come off while the vehicle is in motion.
[RE24330(B )02/89]
eight pica chart:0020314-A*
[RE24397(BEF )02/95]
If the Engine Cranks But Does
Not Start or Does Not Start After
a Collision
*
[RE24400(BEF )04/95]
The Fuel Pump Shut-off Switch
*
[RE24500(BEF )03/95]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[RE24600(BEF )01/95]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
File:ltreb.ex
Update:Fri Jun 9 15:25:48 1995
Page 303 of 376
306
*
[SV26750(BEF )03/90]
In situations where the tires differ from front to
rear (snow/traction), simply rotate using a side
to side pattern.
*
[SV26800(BEF )06/93]
half page art:0020364-A
Tire rotation pattern
*
[SV26900(BEF )10/89]
After each rotation, adjust individual tire
pressure as specified on the Safety Compliance
Certification Label. Tighten wheel lug nuts to the
required torque specification and retighten again
after 500 miles (800 km).
*
[SV27000(BEF )10/94]
If your vehicle has aluminum wheels, you may
demount the full size, non-temporary spare
tire (if so equipped) and remount on an
aluminum wheel to rotate the spare tire into
your vehicle's rotation pattern.
File:ltsvb.ex
Update:Tue Jun 20 16:56:22 1995