ESP FORD CONTOUR 1996 2.G User Guide

Electronic Sound Systems
119
*
[AS04350(ALL)02/95]
Activate Auto Memory Store by pushing the ªAUTO
PRESETº button once. Your radio will set the first five
strong stations of the band you are in (AM, FM1 or FM2)
into the memory buttons. The display will show ªAUTOº,
then run through the frequencies, stopping momentarily on
the stations being set into the memory buttons. The radio is
now in the ªAUTOº mode and this display will show
ªAUTOº each time a preset is activated.
*
[AS04450(ALL)05/95]
NOTE: If there are fewer than five strong stations in the
frequency band, the remaining unfilled buttons will
store the last strong station detected on the band.
*
[AS04550(ALL)05/95]
After all stations have been filled, the radio will begin
playing the station stored on memory button 1.
*
[AS04560(ALL)04/95]
To deactivate the Auto Memory Store mode and return to
the manually-set memory button stations (or those stations
set using Auto Memory Load), simply push the ªAUTO
PRESETº button. Display will show ªAUTOº then ªOFFº.
The next time Auto Memory Store is activated on that band,
the radio will store the next set of five strong stations.
*
[AS04600(ALL)02/95]
Adjusting the tone balance and speaker output of your
radio
*
[AS04700(ALL)04/95]
n
Increasing or decreasing bass response
[AS04750(ALL)07/94]
Push the ªAUDIOº button repeatedly until the display reads
ªBASSº. Push the top (+) of the ªVOLUMEº button to
increase bass (more ªlowsº), and push the button (s)to
decrease bass (less ªlowsº).
*
[AS04800(ALL)04/95]
n
Increasing or decreasing treble response
[AS04900(ALL)07/94]
Push the ªAUDIOº button repeatedly until the display reads
ªTREBº. Push the top (+) of the ªVOLUMEº button to
increase treble (more ªhighsº), and push the bottom (s)to
decrease treble (less ªhighsº).
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

Electronic Sound Systems
133
*
[AS24000(ALL)02/95]
Adjusting the tone balance and speaker output of your
radio
*
[AS24100(ALL)04/95]
n
Increasing or decreasing bass response
*
[AS24225(ALL)05/95]
Push the ªAUDIOº button repeatedly until the display reads
ªBASS.º Push the right (+) side of the ªVOLUMEº button to
increase bass (more ªlowsº), and push the left (±) side to
decrease bass (less ªlowsº).
*
[AS24300(ALL)04/95]
n
Increasing or decreasing treble response
*
[AS24425(ALL)05/95]
Push the ªAUDIOº button repeatedly until the display reads
ªTREB.º Push the right (+) side of the ªVOLUMEº button to
increase the treble (more ªhighsº), and push the left (±) side
to decrease treble (less ªhighsº).
*
[AS24600(ALL)04/95]
n
Adjusting speaker balance
*
[AS24725(ALL)05/95]
Balance control allows you to adjust the sound distribution
between the right and left speakers. Push the ªAUDIOº
button repeatedly until the display reads ªBAL.º Push the
right (+) side of the ªVOLUMEº button to shift the sound to
the right speakers, and push the left (±) side to shift the
sound to the left speakers.
*
[AS24800(ALL)04/95]
n
Adjusting speaker fader
*
[AS24925(ALL)05/95]
Fade control allows you to adjust the sound distribution
between the front and rear speakers. Push the ªAUDIOº
button repeatedly until the display reads ªFADE.º Push the
right (+) side of the ªVOLUMEº button to shift the sound to
the front speakers, and push the left (±) side to shift the
sound to the rear speakers.
*
[AS24950(ALL)04/95]
NOTE: Illuminated bars in the display show relative levels of
bass and treble, and positions of speaker balance and
fader functions (left to right, front to rear).
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

134
%*
[AS25000(ALL)02/95]
Using the Controls of Your Cassette Tape Player
*
[AS25400(ALL)02/95]
NOTE: Radio power must be on to use the cassette tape
player.
*
[AS25500(ALL)02/95]
How to insert a tape
*
[AS25600(ALL)05/95]
Insert a cassette (with the open edge to the right) firmly into the
tape door opening, making sure the cassette is completely in
and ªseated.º
*
[AS25700(ALL)02/95]
How to locate a desired track on the tape
*
[AS25800(ALL)02/95]
NOTE: The tape track number indicated in the display does
not necessarily correspond to the tape track or side
number on the cassette label. It is used only to
indicate when the tape mechanism reverses tracks.
*
[AS25920(ALL)02/95]
n
Using the Automatic Music Search (ªAMSº)
*
[AS25930(ALL)03/95]
Press and hold the ªAMSº button (ªAMSº will appear in the
display). Then, push the left
hbutton to rewind to the
beginning of the current selection or press the right
g
button to fast forward to the beginning of the next selection.
*
[AS25950(ALL)02/95]
n
Fast forwarding the tape
*
[AS26000(ALL)03/95]
Push the right
gbutton to fast forward the tape.
*
[AS26100(ALL)02/95]
n
Rewinding the tape
*
[AS26200(ALL)03/95]
Push the left
hbutton to rewind the tape.
*
[AS26900(ALL)02/95]
n
How to change the side of the tape being played
*
[AS27000(ALL)03/95]
The alternate track (other side) of the tape can be selected at
any time by pushing both fast-wind buttons
hand
g
at the same time.
*
[AS27100(ALL)02/95]
How to eject the tape
*
[AS27250(ALL)02/95]
To stop the tape and eject the cassette, press the ªEJECTº
button. The radio will resume playing.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

Driving Your Contour
151 hazardous driving situations, especially when driving on
hazardous road surfaces. Even with your anti-lock brake system,
you may not have total control of your vehicle when braking on
roads with loose surfaces such as snow or gravel, holes in the
pavement, or alternating patches of slippery and dry surfaces.
*
[DR17500(ALL)05/95]
If the brake pedal is applied while the vehicle is driven over
uneven road surfaces, the ABS may cycle and the driver may
sense a pulsation in the brake pedal, accompanied by a slight
up and down movement of the pedal height and a clicking
sound. This may also happen when driving on an inclined
surface such as a driveway while making a sharp turn. This is a
normal condition.
[DR17600(ALL)05/94]
Your vehicle may have an Anti-lock Brake System feature. If it
does, check the Anti-lock Brake System light each time you start
the engine. If it stays on longer than three (3) seconds, shut off
the engine and restart. If it stays on, that means the Anti-lock
Brake feature is not working and should be serviced
immediately to restore the benefits of the Anti-lock feature.
Normal braking is not affected unless the brake warning light is
also lit.
[DR17650(ALL)05/95]
The Anti-lock Brake System has self-check capabilities. As
described above, the system turns on the anti-lock light each
time you start your engine. After the engine is started and the
anti-lock light turns off, the system performs another test the
first time the vehicle reaches 5 mph (8 km/h) (12 mph
[20 km/h] for vehicles equipped with the traction control
system). The system turns on the ABS pump motor for
approximately 1/2 second. At this time, a mechanical noise may
be heard and felt. This is a normal part of the self-check feature.
If a malfunction is found during this check the anti-lock light
will come on.
*
[DR17700(ALL)12/93]
Ford Motor Company has not found any negative effects of
mobile radio transmitting equipment installed on vehicles with
the ABS system providing that the radio is installed according
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

Driving Your Contour
155
%*
[DR21200(ALL)01/95]
High water
*
[DR21300(ALL)01/95]
Do not drive through flooded areas unless you are sure that the
water is below the bottom of the wheel rims.
*
[DR21400(ALL)04/94]
If you must drive through high water, drive slowly. You may
have limited traction or wet brakes, so allow extra stopping
distance because your vehicle will not stop as quickly as usual.
*
[DR21500(ALL)01/95]
After you drive through the standing water, apply your brakes
gently several times as your vehicle moves slowly. This helps to
dry the brakes.
%*
[DR21600(ALL)03/95]
Driving With a Heavy Load
*
[DR21700(ALL)01/95]
There are limits to the amount of weight your vehicle can carry
or tow. The total weight of your vehicle, plus the weight of the
passengers and cargo, should never be more than the Gross
Vehicle Weight Rating (GVWR). Also, the weight that your
vehicle carries over the front axle and rear axle should never be
more than the Gross Axle Weight Rating (GAWR) for the
respective axle.
%*
[DR21800(ALL)01/95]
You can find your vehicle's GVWR and GAWR on the Safety
Compliance Certification Label on the left front door lock facing
or on the door latch post pillar.
*
[DR21900(ALL)01/95]
The weight limits of your vehicle's tires affect the GVWR or
GAWR limitations. Usage of replacement tires with higher
weight limit than originals does not increase GVWR or GAWR.
Usage of lower capacity replacement tires may lower GVWR
and GAWR limitations.
*
[DR22000(ALL)02/95]
RWARNING
If the GVWR or the GAWR specified on the Safety
Compliance Certification Label is exceeded, your vehicle
may be damaged or you may lose control and injure
someone.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

156
%*
[DR22050(ALL)01/95]
Limiting Your Vehicle's Load
[DR22150(ALL)01/95]
The load that you add to your vehicle must not exceed the
maximum load stated on the Safety Compliance Certification
Label attached to the left front door pillar or the left front door
lock facing.
*
[DR22250(ALL)01/95]
To figure the weight of your vehicle's load, add the weights of:
*
[DR22350(ALL)01/95]
n
the driver and passengers
*
[DR22400(ALL)01/95]
n
luggage and any other items that you put in your vehicle
*
[DR22500(ALL)01/95]
n
the tongue load of the loaded trailer
*
[DR22600(ALL)01/95]
n
the weight of any equipment that has been added to your
vehicle since it was delivered to your dealer
*
[DR22700(ALL)01/95]
If you do not know the actual weights of these items, use the
following procedure to figure the weight of a load:
*
[DR22800(ALL)01/95]1.
Weigh your vehicle without the driver, passengers and
luggage. You might take your vehicle to a shipping company
or an inspection station for trucks.
*
[DR22900(ALL)01/95]2.
Then weigh your vehicle with the driver, passengers and
luggage.
*
[DR23000(ALL)01/95]3.
Subtract the first reading from the second to figure the total
weight of the load.
*
[DR23100(ALL)01/95]
After determining this load, you must also make sure that the
total weight of your vehicle, plus the load it carries, is less than
its GVWR. Also, make sure that the weight your vehicle carries
over each axle is less than the GAWR for the respective axle.
*
[DR23200(ALL)01/95]
You can find the GVWR and GAWR on the Safety Compliance
Certification Label on the left front door lock facing or the door
latch post pillar.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

160
%*
[DR29450(ALL)01/95]
Connecting the trailer's brakes
*
[DR29500(ALL)01/95]
Electric brakes and manual, automatic, or surge-type hydraulic
brakes are safe if you install them properly and adjust them
according to the manufacturer's instructions. Be sure that your
trailer's brakes meet local and federal regulations.
*
[DR29600(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake system directly
to your vehicle's brake system. Your vehicle may not
have enough braking power and your chances of having
a collision greatly increase.
%*
[DR29650(ALL)01/95]
Connecting the trailer's lights
*
[DR29700(ALL)01/95]
Do not connect a trailer's lighting system wiring directly to
your vehicle's lighting system wiring.To get the proper
equipment for hooking up your trailer's lights, see your local
trailer dealer and your Ford dealer. Be sure to follow their
instructions carefully.
*
[DR29800(ALL)01/95]
If you do not install trailer lights correctly, you may cause
damage to the vehicle's lighting system.
%*
[DR29900(ALL)01/95]
Driving While You Tow
*
[DR30000(ALL)05/95]
Be especially careful when driving while you tow a trailer.
Never drive faster than 45 mph (70 km/h) when you tow in
hilly country on hot days. Also, anticipate stops so that you can
brake gradually.
[DR30050(ALL)01/95]
If your vehicle has a manual transaxle and you are towing a
trailer, you should select gear positions which will avoid jerking
or excessive engine speed. If you need to drive excessively in 1
(First) or 2 (Second), it may indicate that the trailer is too big or
heavily loaded for your vehicle's drivetrain. Continuous driving
in these two gears while towing a trailer is not recommended.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

188
*
[HS08800(ALL)06/95]
Officials at the embassy or consulate can tell you where to get
unleaded fuel. If you cannot get unleaded fuel or can get only
fuel with an anti-knock index that is lower than your vehicle
needs, contact a district or owner relations office before you
leave the U.S. or Canada.
*
[HS08900(ALL)06/95]
Use of leaded fuel in your vehicle without a proper conversion
may damage the effectiveness of your emissions control system
and may cause engine knocking or serious engine damage. Ford
Motor Company is not responsible for any damage that is
caused by use of improper fuel.
*
[HS09000(ALL)06/95]
You may also have difficulty importing your vehicle back into
the U.S. if you use leaded fuel.
*
[HS09100(ALL)06/95]
If your vehicle must be serviced while you are traveling or
living in Central or South America, the Caribbean, or the
Middle East, contact the nearest Ford dealership. If the
dealership cannot help you, write to:
[HS09200(ALL)01/95]
7-1/2 pica art:0001307-C*
[HS09300(ALL)06/95]
If you are in other foreign countries, contact the nearest Ford
dealership. If the dealership cannot help you, they can direct
you to the appropriate Ford affiliate office.
*
[HS09400(ALL)06/95]
If you buy your vehicle in North America and then relocate
outside of the U.S. or Canada, register your Vehicle
Identification Number and new address with Ford Motor
Company Export Operations.
File:cdhso.ex
Update:Thu Jan 25 12:28:07 1996

Accessories
191
*
[AC00600(ALL)01/95]
NOTE: When adding accessories, equipment, passengers, and
luggage to your vehicle, do not exceed the total
weight capacity of the vehicle or of the front or rear
axle (GVWR, GAWR as shown on the Safety
Compliance Certification Label). Consult your dealer
for specific weight information.
*
[AC00700(ALL)05/95]
NOTE: The Federal Communications Commission (FCC) or
the Canadian Radio Telecommunications Commission
(CRTC) regulates the use of mobile communications
systems Ð such as two-way radios, telephones, and
theft alarms Ð that are equipped with radio
transmitters. Any such equipment installed in your
vehicle should comply with FCC or CRTC regulations
and should be installed only by a qualified technician.
*
[AC00800(ALL)01/95]
NOTE: Mobile communications systems may harm the
operation of your vehicle, particularly if they are not
properly designed for automotive use or are not
properly installed. For example, when operated, such
systems may cause the engine to stumble or stall. In
addition, such systems may themselves be damaged or
their operation affected by operating your vehicle.
(Citizens band [CB] transceivers, garage door openers,
and other transmitters whose power output is 5 watts
or less will not ordinarily affect your vehicle's
operation.)
*
[AC00900(ALL)05/95]
NOTE: Because we have no control over the installation,
design, or manufacture of such systems, Ford cannot
assume responsibility for any adverse effects or
damage that may result if you use this equipment.
File:cdaco.ex
Update:Thu Jan 25 12:30:23 1996

196
*
[SV01275(ALL)03/95]
Use only recommended fuels, lubricants, fluids, and service
parts conforming to Ford specifications. Motorcraft parts are
designed and built to provide the best performance in your
vehicle. Using these parts for replacement is your assurance that
Ford-built quality stays in your vehicle.
%*
[SV01280(ALL)04/95]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
*
[SV01600(ALL)03/95]
Precautions When Servicing Your Vehicle
*
[SV01700(ALL)01/95]
Be especially careful when inspecting or servicing your vehicle.
Here are some general precautions for your safety:
%*
[SV01800(ALL)03/95]
n
Do not work on a hot engine. The engine cooling fan may
come on unexpectedly. Always turn the engine off and let it
cool.
*
[SV01850(ALL)05/95]
RWARNING
The cooling fan is automatic and may come on at any
time. Always disconnect the negative terminal of the
battery before working near the fan.
*
[SV01900(ALL)03/95]
n
If you must work with the engine running, avoid wearing
loose clothing or jewelry that could get caught in moving
parts. Take appropriate precautions with long hair.
*
[SV02000(ALL)01/95]
n
Do not work on a vehicle in an enclosed space with the
engine running, unless you are sure you have enough
ventilation.
*
[SV02100(ALL)01/95]
n
Never get under a vehicle while it is supported by a jack
only. If you must work under a vehicle, use safety stands.
File:cdsvo.ex
Update:Thu Jan 25 12:09:28 1996