key FORD CONTOUR 1996 2.G User Guide

Instrument Panel Controls
71
*
[IP00500(ALL)01/95]
The Climate Control Systems
[IP00625(ALL)01/95]
Your vehicle has one of the following:
[IP00800(ALL)02/94]
n
Heating Only System (Without Air Conditioning)
*
[IP00900(ALL)02/95]
n
Heating and Air Conditioning System
*
[IP01100(ALL)09/89]
If you are not sure which system your vehicle has, see the
diagrams on the following pages.
[IP01201(ALL)03/95]
Heating Only System
[IP01220(ALL)05/94]
The control for your heater system is located at the center of the
instrument panel below the radio. The heater will operate only
when the ignition key is turned to the ON position. Your heater
will heat and/or ventilate your vehicle interior depending on
the function selector knob position and temperature you select.
The function selector knob allows you to select heating or
ventilation and determine where the air will be directed. The
temperature control knob setting determines the temperature of
the air that flows into the vehicle.
[IP01250(O )03/95]
10-1/2 pica
art:0001181-B
The control for the heating only system
File:cdipo.ex
Update:Thu Jan 25 12:18:07 1996

76
% [IP03500(ALL)05/95]
Rear Window Defroster and Heated Side View
Mirrors (If equipped)
[IP03551(ALL)02/95]
The defroster for the rear window clears frost, fog, or thin ice
from both the inside and outside of the rear window and
activates the heated side view mirrors.
[IP03600(ALL)01/95]
The button for the rear window defroster and heated side view
mirrors is on the instrument panel, to the right of the steering
wheel.
[IP03700(ALL)02/94]
6 pica art:0001180-B
The rear window defroster and heated side view mirrors
[IP03900(ALL)05/95]
Clear away any snow that is on the rear window and side view
mirrors before using the defroster. With the engine running,
push the defroster button.
*
[IP04000(ALL)04/95]
After approximately 10 minutes, the defroster will turn off. If
the window or mirrors are still not clear, turn the defroster on
again.
*
[IP04100(ALL)04/95]
The defroster will turn off when the ignition key is turned to
the OFF or START position.
*
[IP23000(ALL)03/94]
NOTE: Never use sharp instruments or window cleaners with
abrasives to clean the inside of your rear window. If
you do, you may damage the heating elements that
are bonded to the inside of the rear window and
cause damage to the rear window defroster.
File:cdipo.ex
Update:Thu Jan 25 12:18:07 1996

Instrument Panel Controls
81
[IP32900(ALL)11/93]
Dome lamp delay
[IP33000(ALL)05/94]
Your vehicle may have a dome lamp delay. If you set the
switch on the dome lamp to the 12-second delay position, the
dome lamp will turn on when either front door is opened.
[IP33100(ALL)11/93]
The dome lamp will turn off after 12 seconds or when the
ignition key is turned to the ON or ACC position. It will not
turn off if either front door is open or if you move the dome
lamp switch to the ON position.
*
[IP33125(ALL)04/95]
Your interior dome lamps and map lamps are plastic and
should be cleaned with a mild detergent diluted in water. Rinse
them with clear water.
[IP33150(ALL)01/95]
Turning On the Map Lamps (If equipped)
*
[IP33200(ALL)01/94]
Your vehicle may have a map lamp for the passenger and one
for the driver.
[IP33250(ALL)11/93]
7-1/2 pica art:0001218-A
Turning on the map lamps
File:cdipo.ex
Update:Thu Jan 25 12:18:07 1996

84
*
[SC02800(ALL)05/95]
High Beams and Flashing the Lamps
[SC02900(ALL)05/95]
To turn on the high beams, turn the headlamp control knob to
the headlamp ON position and push the turn signal lever away
from you until it latches. When the high beams are on, the high
beam indicator light on the instrument cluster comes on.
[SC03000(ALL)10/93]
To turn off the high beams, pull the lever back to the off
position.
*
[SC03400(ALL)06/95]
To flash the headlamps, pull the lever toward you for a moment
and then release it. The headlamps will flash whether the
headlamp knob is in the on or off position.
*
[SC03700(ALL)03/95]
Windshield Wipers and Washer
*
[SC03800(ALL)03/95]
To turn on the windshield wipers, the ignition key must be
turned to the ON or ACC position.
[SC04400(ALL)05/95]
10-1/2 pica
art:0001189-D
Using the windshield wiper
[SC04500(ALL)02/94]
The windshield wipers can be set on high, low speed or interval
wipe. Turn the ring on the lever to set a longer or shorter pause
between wiping cycles.
File:cdsco.ex
Update:Thu Jan 25 12:10:03 1996

94
[FV01240(ALL)01/95]
Find the lever at the black label with word LOCKED in white
letters. Move the lever toward the inside of the door.
*
[FV01260(ALL)03/95]
To release the childproof lock, open the rear door from the
outside.
[FV01280(ALL)01/95]
Move the lever toward the outside of the door.
*
[FV01300(ALL)04/95]
Power Door Locks (If equipped)
[FV01400(ALL)01/95]
If your vehicle has power door locks, the controls to lock the
doors are on the trim panel of the front door. When you close
the doors after you set the door locks, the doors remain locked.
If the power mechanism fails, the manual door lock will
automatically override the power controls.
[FV01500(ALL)05/94]
10-1/2 pica
art:0001250-B
The power door lock on the driver's door
%*
[FV01530(ALL)01/95]
Using the Illuminated Entry System (If equipped)
[FV01560(ALL)05/95]
If your vehicle is equipped with the illuminated entry system,
the interior lights turn on when you lift the outside door handle
on either front door.
[FV01590(ALL)01/95]
These lights automatically turn off after 12 seconds or when you
turn the ignition key to ON or ACC. The inside lights will not
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

Features
95 turn off if you have turned them on with the switch in the
dome lamp or if the front door is open.
[FV01600(ALL)05/95]
Remote Entry System (If equipped)
*
[FV01700(ALL)03/94]
If your vehicle has the remote entry system, you can lock and
unlock the vehicle doors and open the trunk without using a
key. The remote also has a personal alarm feature. The buttons
for the system are located on the hand held transmitter(s) that
came with your vehicle.
[FV01800(ALL)02/95]
The system will work with up to four transmitters. Additional
transmitters can be ordered from your dealer.
*
[FV01900(ALL)02/95]
The remote entry features only operate with the ignition in the
OFF position.
[FV02000(ALL)11/93]
10-1/2 pica
art:0001221-A
Remote entry transmitter
%*
[FV02100(ALL)02/95]
Unlocking the doors and opening the trunk
*
[FV02200(ALL)02/95]
To unlock the driver's door, press the UNLOCK button.
*
[FV02300(ALL)02/95]
To unlock the other doors, press the UNLOCK button a second
time within five seconds of unlocking the driver's door.
*
[FV02400(ALL)02/95]
To open the trunk, press the TRUNK button.
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

96
[FV02500(ALL)05/94]
When you use the remote entry UNLOCK, TRUNK or PANIC
buttons, the illuminated entry system turns on the interior
lights for 12 seconds. You can turn these lights off by turning
the ignition to the ON position. The interior lights will not turn
off if you have turned them on manually or if a door is open.
[FV02550(ALL)05/94]
NOTE: The illuminated entry system will only work when
the dome light switch is in the ª12º position.
*
[FV02600(ALL)02/95]
Locking the doors
*
[FV02700(ALL)02/95]
To lock all the doors, press the LOCK button.
*
[FV02800(ALL)01/95]
If you would like a signal that the doors are being locked, press
the LOCK button again within five seconds. The doors will lock
again, the horn will beep and the low beam headlamps and tail
lamps will flash.
%*
[FV02900(ALL)02/95]
Activating the remote personal alarm
[FV03000(ALL)04/94]
If you wish to activate the remote personal alarm, press the
PANIC button. This will honk the horn and flash the low beam
headlamps and tail lamps for approximately two minutes
forty-five seconds. You can turn it off by pressing the PANIC
button again on the same transmitter or by turning the ignition
key to the ON position.
%*
[FV03100(ALL)02/95]
Replacing the batteries
*
[FV03200(ALL)02/95]
The remote entry transmitter is powered by two coin type
three-volt lithium 2016 batteries (included) that should last for
several years of normal use. If you notice a significant decrease
in operating range, the batteries should be replaced.
Replacement batteries can be purchased at most pharmacies,
watch stores or at your Ford or Lincoln-Mercury dealer.
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

Features
111
*
[FV17000(ALL)01/95]
Storage Compartments
[FV17100(ALL)01/95]
Your vehicle may have several storage compartments:
[FV17201(ALL)01/95]
n
two map pockets on the panels of the front doors. The back
of the front seats may also have map pockets.
[FV17301(ALL)01/95]
n
a coin holder on the instrument panel
[FV17501(ALL)01/95]
n
a small storage pocket on the outside of the front seat base
*
[FV17800(ALL)01/95]
Trunk
[FV17900(ALL)11/93]
To open the trunk manually, use the oval key.
[FV18000(ALL)01/95]
Remote Trunk Release (If equipped)
[FV18100(ALL)05/94]
The remote trunk release is on the floor to the left of the
driver's seat.
[FV18200(ALL)05/94]
7-1/2 pica art:0000984-E
The remote trunk release
[FV18300(ALL)05/94]
You can disable the remote trunk release. If you depress the
lever on the trunk latch that is marked in orange before closing
the trunk, the trunk can only be opened with the key.
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

Electronic Sound Systems
123
*
[AS07750(ALL)04/95]
How to stop and restart the CD player
*
[AS07800(ALL)04/95]
When a disc is loaded, the unit automatically enters the play
mode and the play indicator
ailluminates. To stop
temporarily, press the ªPLAY/STOPº button or the ªAM/FMº
button. The stop indicator
Xin the display illuminates and
operation returns to the radio mode. To resume CD play, press
the ªPLAY/STOPº button once again.
*
[AS07850(ALL)04/95]
NOTE: If the ignition key is turned OFF during play and
then is set to the ON or ACCESSORY position, the
CD player will resume playing in the mode it was in
when ignition was turned off.
*
[AS07860(ALL)03/95]
How to locate a selection on your CD player using
Automatic Music Search (AMS)
*
[AS07880(ALL)03/95]
An ªAMSº (Automatic Music Search) control on your CD player
allows you to quickly find a particular selection on the disc.
Press the left
fside of the ªAMSº control to locate a
previous selection or the right
eside of the ªAMSº control
to locate a later selection.
*
[AS07900(ALL)05/95]
How to fast forward or reverse your CD player
[AS07950(ALL)05/95]
To quickly search for a particular point in a selection, press the
right
ebutton (to fast forward) or the left
fbutton
(to reverse). While either button is pressed, the disc goes
forward or backward at two different speeds depending on how
long the button is held down. (Pressing either button for more
than approximately three seconds will speed up the process.)
Release the button at the desired point (found by watching the
elapsed playing time in the display or listening to the sound
during fast forward or reverse).
*
[AS08000(ALL)03/95]
When you have reached the end of the disc by keeping the fast
forward
eside of the button pressed, the display will show
the end time of the last track and the sound will be muted.
When the fast forward
eside of the button is released, the
player resumes play at the beginning of the first track.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

140
*
[DR00900(ALL)01/95]
Putting Your Vehicle in Gear
[DR00915(ALL)05/95]
You must push in the thumb button to move the gearshift to
the position you choose.
*
[DR00917(ALL)05/95]
RWARNING
Hold the brake pedal down while you move the gearshift
lever from position to position. If you do not hold the
brake pedal down, your vehicle may move unexpectedly
and injure someone.
*
[DR00918(ALL)03/95]
To operate:
*
[DR00919(ALL)01/95]1.
Start the engine.
*
[DR00920(ALL)01/95]2.
Depress and hold the brake pedal.
*
[DR00921(ALL)01/95]3.
Move the gearshift lever out of P (Park).
%*
[DR00923(ALL)04/95]
Your vehicle is equipped with a Brake Shift Interlock safety
feature. This feature prevents the gearshift from being moved
from the P (Park) position until the brake pedal is depressed.
This feature is active when the ignition is in the ON position. If
the gearshift lever CANNOT be moved from P (Park) with the
brake pedal depressed:
*
[DR00924(ALL)01/95]1.
Turn the engine off and remove the ignition key.
[DR00925(ALL)05/94]2.
With the parking brake applied and the brake pedal
depressed, insert a screwdriver about 2" (5 cm) into the
square opening to the right of the gearshift at the base of the
console.
[DR00926(ALL)05/94]3.
Rotate the screwdriver point rearward.
[DR00927(ALL)02/94]4.
Push and hold the thumb button and move the gearshift.
[DR00928(ALL)02/94]5.
Remove the screwdriver when the gearshift moves from the
P (Park) position.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996