light FORD CONTOUR 1996 2.G Owner's Guide

Steering Column Controls
91
[SC09500(ALL)05/95]
To Cancel Speed Control
[SC09600(ALL)05/95]
Speed control can be cancelled at any time by pressing the
brake pedal slightly. After cancelling, you can return to the
speed you set by pressing the RES switch, or set a new speed
by pressing the SET ACC or COAST switch.
%*
[SC10900(ALL)06/95]
Cancelling and Resuming a Set Speed
[SC11000(ALL)05/95]
If you press the brake pedal, the speed control is suspended.
You can return to the set speed by pressing the RES switch, as
long as you did not press the OFF switch. You must be driving
at least 30 mph (50 km/h).
*
[SC11300(ALL)05/95]
Your vehicle will gradually return to the previously set speed
and then maintain it.
%*
[SC11360(ALL)05/95]
To Turn Off the Speed Control System
*
[SC11370(ALL)05/95]
Press the OFF switch.
*
[SC11380(ALL)05/95]
In addition, the speed control is turned off each time you turn
the vehicle off.
File:cdsco.ex
Update:Thu Jan 25 12:10:03 1996

94
[FV01240(ALL)01/95]
Find the lever at the black label with word LOCKED in white
letters. Move the lever toward the inside of the door.
*
[FV01260(ALL)03/95]
To release the childproof lock, open the rear door from the
outside.
[FV01280(ALL)01/95]
Move the lever toward the outside of the door.
*
[FV01300(ALL)04/95]
Power Door Locks (If equipped)
[FV01400(ALL)01/95]
If your vehicle has power door locks, the controls to lock the
doors are on the trim panel of the front door. When you close
the doors after you set the door locks, the doors remain locked.
If the power mechanism fails, the manual door lock will
automatically override the power controls.
[FV01500(ALL)05/94]
10-1/2 pica
art:0001250-B
The power door lock on the driver's door
%*
[FV01530(ALL)01/95]
Using the Illuminated Entry System (If equipped)
[FV01560(ALL)05/95]
If your vehicle is equipped with the illuminated entry system,
the interior lights turn on when you lift the outside door handle
on either front door.
[FV01590(ALL)01/95]
These lights automatically turn off after 12 seconds or when you
turn the ignition key to ON or ACC. The inside lights will not
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

96
[FV02500(ALL)05/94]
When you use the remote entry UNLOCK, TRUNK or PANIC
buttons, the illuminated entry system turns on the interior
lights for 12 seconds. You can turn these lights off by turning
the ignition to the ON position. The interior lights will not turn
off if you have turned them on manually or if a door is open.
[FV02550(ALL)05/94]
NOTE: The illuminated entry system will only work when
the dome light switch is in the ª12º position.
*
[FV02600(ALL)02/95]
Locking the doors
*
[FV02700(ALL)02/95]
To lock all the doors, press the LOCK button.
*
[FV02800(ALL)01/95]
If you would like a signal that the doors are being locked, press
the LOCK button again within five seconds. The doors will lock
again, the horn will beep and the low beam headlamps and tail
lamps will flash.
%*
[FV02900(ALL)02/95]
Activating the remote personal alarm
[FV03000(ALL)04/94]
If you wish to activate the remote personal alarm, press the
PANIC button. This will honk the horn and flash the low beam
headlamps and tail lamps for approximately two minutes
forty-five seconds. You can turn it off by pressing the PANIC
button again on the same transmitter or by turning the ignition
key to the ON position.
%*
[FV03100(ALL)02/95]
Replacing the batteries
*
[FV03200(ALL)02/95]
The remote entry transmitter is powered by two coin type
three-volt lithium 2016 batteries (included) that should last for
several years of normal use. If you notice a significant decrease
in operating range, the batteries should be replaced.
Replacement batteries can be purchased at most pharmacies,
watch stores or at your Ford or Lincoln-Mercury dealer.
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

Features
109
%*
[FV15500(ALL)05/95]
Sun Visors
*
[FV15600(ALL)04/95]
Illuminated Visor Mirror (If equipped)
[FV15700(ALL)05/94]
Your vehicle may have lighted mirrors on the sun visors. The
mirror is lit by sliding open the mirror cover.
[FV15800(ALL)11/93]
10-1/2 pica
art:0000588-B
The visor mirror
File:cdfvo.ex
Update:Thu Jan 25 12:20:30 1996

126
*
[AS08700(ALL)04/95]
n
Do not expose the disc to direct sunlight or heat sources
such as defroster and floor heating ducts. Do not leave any
discs in a parked car in direct sunlight where there may be a
considerable rise in temperature or damage may result.
*
[AS08800(ALL)04/95]
n
After playing, store the disc in its case.
*
[AS08900(ALL)04/95]
n
If a disc has already been inserted, do not try to insert
another disc. Doing so may damage the disc player.
*
[AS09000(ALL)04/95]
n
Do not insert anything other than a disc into the disc player.
*
[AS09100(ALL)04/95]
CAUTION:The use of optical instruments with this product
will increase eye hazard as the laser beam used in this compact
disc player is harmful to the eyes. Do not attempt to
disassemble the case. Refer servicing to qualified personnel only.
*
[AS09200(ALL)04/95]
Common Operating Conditions of Your CD Player
*
[AS09300(ALL)04/95]
The following information is designed to help you recognize
typical situations that could be mistakenly interpreted as
mechanical malfunctions of the disc player.
*
[AS09400(ALL)04/95]
n
A disc is already loaded.
*
[AS09500(ALL)04/95]
n
The disc is inserted with the label surface downward.
*
[AS09600(ALL)04/95]
n
The disc is dusty or defective.
*
[AS09700(ALL)05/95]
n
The player's internal temperature is above167ÊF (75ÊC).
Allow the player to cool off before operating.
*
[AS09800(ALL)04/95]
n
Different manufacturers of compact discs may produce discs
with different dimensions or tolerances, some of which may
not be within industry standards or in accordance with the
CD format. Because of this, a new disc that is free of dust
and scratches could be defective and may not play on your
Ford Compact Disc Player.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

Electronic Sound Systems
135
*
[AS27300(ALL)02/95]
Using the DolbyHB noise reduction feature
*
[AS27400(ALL)02/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
*
[AS27550(ALL)05/95]
Push station memory button 3 to activate DolbyHB Noise
Reduction.
*
[AS27600(ALL)02/95]
Tips on Caring for the Cassette Player and Tapes
*
[AS27700(ALL)02/95]
In order to keep your cassette tape player performing the way it
was meant to, read and follow these simple precautions:
*
[AS27750(ALL)02/95]
n
Using a Ford Cassette Cleaning Cartridge to clean the tape
player head after 10-12 hours of play will help maintain the
best playback sound and proper tape operation.
*
[AS27800(ALL)02/95]
n
Only cassettes that are 90 minutes long or less should be
used. Tapes longer than 90 minutes are thinner and subject
to breakage or may jam the tape player mechanism.
*
[AS27900(ALL)02/95]
n
Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS28001(ALL)02/95]
n
If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS28101(ALL)02/95]
n
Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
a cassette.
*
[AS28200(ALL)03/95]
n
Do not leave a tape in the cassette tape player when not in
use. High heat in the vehicle can cause the cassette to warp.
File:cdaso.ex
Update:Thu Jan 25 12:21:48 1996

142
[DR01100(ALL)05/94]
13-1/2 pica
art:0000492-D
Console-mounted automatic transaxle shift control lever
%*
[DR01600(ALL)01/95]
R (Reverse)
*
[DR01700(ALL)02/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR01725(ALL)01/95]
N (Neutral)
[DR01750(ALL)11/94]
In N (Neutral), the wheels of the transaxle are not locked. Your
vehicle will roll freely, even on the slightest incline, unless the
parking brake or brakes are on.
*
[DR01800(ALL)01/95]
Driving
[DR01825(ALL)02/94]
Your vehicle's gearshift is console-mounted on the floor. The
Transaxle Control Switch (TCS) is located on the gearshift
handle. The transaxle control indicator light (OD OFF) is located
on the instrument panel. You can put the gearshift lever in any
of the several positions.
[DR01850(ALL)05/94]
The OD OFF light is off (not illuminated) during normal vehicle
operation. This allows the transaxle to upshift and downshift
from first through fourth gears. When the TCS is pressed, the
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

Driving Your Contour
143 transaxle control indicator light will illuminate (OD OFF) on the
instrument panel. When this OD OFF is illuminated the
transaxle will upshift and downshift from first through third
gears and provide coast braking in second and third gears.
[DR01875(ALL)02/94]
To return the transaxle to normal operation (first through fourth
gears) depress the TCS again. This switch may be used to cancel
overdrive any time the vehicle is being driven. Each time your
vehicle is started, the overdrive system will automatically be in
the normal overdrive mode and the light will not be
illuminated.
[DR01900(ALL)05/94]
When to use D (Overdrive Ð without Transaxle Control
Switch activated)
[DR01925(ALL)05/94]
D (Overdrive) is the usual driving position for an automatic
overdrive transaxle. It automatically upshifts or downshifts as
the vehicle speeds or slows.
[DR01950(ALL)05/94]
However, D (Overdrive) also shifts into a fourth gear Ð an
overdrive gear Ð when your vehicle cruises at a consistent
speed for any length of time. This fourth gear will increase your
fuel economy when you travel at cruising speeds.
[DR02000(ALL)05/94]
When to use D (Drive Ð with Transaxle Control Switch
activated)
[DR02025(ALL)05/94]
D (Overdrive) may not be appropriate for certain terrain. If the
transaxle shifts back and forth between third and fourth gears
while you are driving on hilly roads or if your vehicle requires
additional power for climbing hills, depress the TCS. D (Drive)
also gives more engine braking to slow your vehicle on
downgrades than D (Overdrive).
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

148
[DR09700(ALL)05/95]
Downshifting
*
[DR09800(ALL)03/95]
When you slow down or climb a steep hill, always downshift
before the engine starts to lose power. Downshifting reduces the
chance of stalling and gives your vehicle better acceleration to
increase speed again.
*
[DR09900(ALL)03/95]
When you drive down steep hills, downshifting helps you keep
a safe speed and helps prevent unnecessary wear on the brakes.
*
[DR10000(ALL)03/95]
When you come to a stop, do not downshift through each gear.
Disengage the clutch and use the brake as necessary.
Downshifting through the gears decreases your vehicle's fuel
economy.
[DR10201(ALL)05/95]
Do not attempt to shift into 1 (First) gear with the clutch pedal
depressed at speeds higher than 20 mph (30 km/h). If you do,
it could cause a complete clutch failure, making your vehicle
inoperative.
[DR10301(ALL)01/95]
Traction Control (If equipped)
[DR10405(ALL)05/95]
The traction control system prevents the wheels from spinning
on slippery roads.
[DR10505(ALL)05/95]
Working with the anti-lock brake system, the traction control
system monitors the speed of the wheels as they roll over the
road surface. When a wheel starts to spin because of slippery
conditions, the traction control system slows the engine by
closing the throttle. At speeds below 35 mph (55 km/h) the
traction control system also applies the brake to the spinning
wheel.
[DR10605(ALL)05/95]
When the traction control system becomes active, the driver
may notice a very slight kick and then a hard resistance in the
accelerator pedal, and a mechanical noise. The traction control
system light on the instrument panel comes on or flashes on
and off during activation.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996

Driving Your Contour
149
[DR10705(ALL)05/95]
The traction control system can be turned off manually by
pushing the T/C OFF button on the instrument panel to the left
of the steering wheel. The traction control system light will
remain on as a reminder that the system is turned off.
[DR10805(ALL)05/94]
Each time the vehicle is started, the traction control system will
automatically be on. When the ignition is turned to the ON
position, the traction control system light comes on for
approximately three (3) seconds.
[DR10905(ALL)05/95]
If the light does not come on when the ignition is turned to the
ON position or if it does not come on when the T/C OFF
button is pressed, have the system serviced by your dealer or a
qualified service technician as soon as possible to restore the
benefits of the traction control feature. You do not need to have
the vehicle towed in.
*
[DR15600(ALL)01/95]
Steering Your Vehicle
%*
[DR15800(ALL)01/95]
Your vehicle comes with power steering. Power steering uses
energy from the engine to help steer your vehicle.
%*
[DR15900(ALL)04/95]
If the amount of effort needed to steer your vehicle changes at a
constant vehicle speed, have the power steering system checked.
If the power steering system breaks down (or if the engine is
turned off), you can steer the vehicle manually but it takes more
effort.
*
[DR16000(ALL)01/95]
Never hold the steering wheel to the extreme right or left for
more than five seconds if the engine is running. This can
damage the power steering pump.
[DR16200(ALL)01/95]
Brakes
%*
[DR16300(ALL)01/95]
Applying the Brakes
[DR16450(ALL)05/94]
Your vehicle may have four-wheel power anti-lock disc brakes
or power front disc and rear drum anti-lock brakes which adjust
automatically through everyday use.
File:cddro.ex
Update:Thu Jan 25 12:23:16 1996