ignition FORD CONTOUR 1997 2.G Owner's Manual

Controls and Features
79
*
[CF27200(ALL)05/96]
Remote Entry System (If equipped)
*
[CF27300(ALL)05/96]
If your vehicle has the remote entry system, you can lock and
unlock the vehicle doors and open the trunk without using a
key. The remote also has a personal alarm feature. The controls
for the system are located on the hand held transmitter(s) that
came with your vehicle.
[CF27400(ALL)12/95]
The system will work with up to four transmitters. Additional
transmitters can be ordered from your dealer.
*
[CF27500(ALL)01/96]
The remote entry features only operate with the ignition in the
OFF position.
[CF27600(ALL)12/95]
10-1/2 pica
art:0001221-A
Remote entry transmitter
%*
[CF27700(ALL)02/96]
Unlocking the doors and opening the trunk
*
[CF27800(ALL)04/96]
To unlock the driver's door, press the UNLOCK control.
*
[CF27900(ALL)04/96]
To unlock the other doors, press the UNLOCK control a second
time within five seconds of unlocking the driver's door.
*
[CF28000(ALL)04/96]
To open the trunk, press the TRUNK control.
File:05cdcfo.ex
Update:Fri Sep 13 08:48:17 1996

80
[CF28100(ALL)05/96]
When you use the remote entry UNLOCK, TRUNK or PANIC
controls, the illuminated entry system turns on the interior
lights for 12 seconds. You can turn these lights off by turning
the ignition to the ON position. The interior lights will not turn
off if you have turned them on manually or if a door is open.
[CF28200(ALL)12/95]
NOTE: The illuminated entry system will only work when
the dome light switch is in the ª12º position.
*
[CF28300(ALL)04/96]
Locking the doors
*
[CF28400(ALL)04/96]
To lock all the doors, press the LOCK control.
*
[CF28500(ALL)04/96]
If you would like a signal that the doors are being locked, press
the LOCK control again within five seconds. The doors will lock
again and the horn will beep.
%*
[CF28600(ALL)03/96]
Activating the remote personal alarm
[CF28700(ALL)05/96]
If you wish to activate the remote personal alarm, press the
PANIC control. This will honk the horn and flash the low beam
headlamps and tail lamps for approximately two minutes
forty-five seconds. You can turn it off by pressing the PANIC
control again on the same transmitter or by turning the ignition
key to the ON position.
%*
[CF28800(ALL)03/96]
Replacing the Batteries
*
[CF28900(ALL)01/96]
The remote entry transmitter is powered by two coin type
three-volt lithium 2016 batteries (included) that should last for
several years of normal use. If you notice a significant decrease
in operating range, the batteries should be replaced.
Replacement batteries can be purchased at most pharmacies,
watch stores or at your Ford or Lincoln-Mercury dealer.
File:05cdcfo.ex
Update:Fri Sep 13 08:48:17 1996

100
*
[SS11801(ALL)03/96]
Determining if System Is Operational
*
[SS11901(ALL)03/96]
The Air Bag Supplemental Restraint System uses a readiness
light and a tone to indicate the condition of the system. The
readiness light is in the instrument cluster. When you turn the
ignition key to ON, this light will illuminate for approximately
six (6) seconds and then turn off. This indicates that the system
is operating normally. NOTE: Routine maintenance of the air
bag system is not required.
%*
[SS12001(ALL)03/96]
A problem with the system is indicated by one or more of the
following:
*
[SS12101(ALL)03/96]
n
the readiness light will either flash or stay lit,
*
[SS12201(ALL)03/96]
n
the readiness light will not light immediately after ignition is
turned on,
%*
[SS12301(ALL)12/95]
n
a group of five beeps will be heard. The tone pattern will
repeat periodically until the problem and light are repaired.
*
[SS12401(ALL)03/96]
If any of these things happen, even intermittently, have the Air
Bag Supplemental Restraint System serviced at your Ford or
Lincoln-Mercury dealer immediately. Unless serviced, the system
may not function properly in the event of a collision.
*
[SS12501(ALL)03/96]
Disposal of Air Bags and Air Bag Equipped Vehicles
*
[SS12601(ALL)03/96]
For disposal of air bags or air bag equipped vehicles, see your
local Ford or Lincoln-Mercury dealer. Air bags MUST BE
disposed of by qualified personnel.
%*
[SS13400(ALL)01/96]
Safety Restraints for Children
*
[SS13500(ALL)01/96]
In the U.S. and Canada, you are required by law to use safety
restraints for children. If small children ride in your vehicle Ð
this generally includes children who are four years old or
younger and who weigh 40 pounds (18 kg) or less Ð you must
put them in safety seats that are made specially for children.
Safety belts alone do not provide maximum protection for these
children. Check your local and state laws for specific
requirements.
File:06cdsso.ex
Update:Thu Sep 12 11:03:20 1996

118
%*
[TO02200(ALL)01/96]
Starting Your Engine
*
[TO02300(ALL)01/96]
To start your engine:
*
[TO02400(ALL)01/96]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[TO02500(ALL)01/96]2.
Keep your foot on the brake pedal and turn the ignition key
to the ON position.
*
[TO02600(ALL)01/96]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[TO02700(ALL)01/96]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[TO02800(ALL)01/96]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
%*
[TO02900(ALL)01/96]
For a cold engine:
[TO03000(ALL)12/95]
2.0L engine:
[TO03100(ALL)12/95]
n
At temperaturesbelow-10ÊF (-23ÊC):Turn the key to ON,
crank the engine and depress the accelerator about 1/4 of
the way down and hold that position forfive (5) seconds.If
the engine fails to start, continue to crank with the
accelerator depressed about 1/4 of the way down and hold
that position until the engine starts.DO NOT crank for
more than 30 seconds,or you could damage the starter. If
the engine fails to start on the first try, turn the key to OFF
and wait two (2) minutes before trying again. Allow engine
to warm up for a few minutes before putting transaxle into
gear.
File:08cdtoo.ex
Update:Thu Sep 12 11:03:39 1996

120
%*
[TO03900(ALL)01/96]
For a warm engine:
[TO04000(ALL)12/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, wait a few seconds after the
starter stops, then try again.
*
[TO04100(ALL)01/96]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
*
[TO04200(ALL)01/96]
After you start the engine, let it idle for a few seconds. Keep
your foot on the brake pedal and put the gearshift lever in gear.
Release the parking brake. Slowly release the brake pedal and
drive away in the normal manner.
*
[TO04300(ALL)12/95]
NOTE: If your vehicle is equipped with an automatic
transaxle, your vehicle has an interlock that prevents
you from shifting out of P (Park) unless your foot is
on the brake pedal.
%*
[TO04400(ALL)01/96]
If the engine does not start after two attempts:
[TO04500(ALL)12/95]1.
Press the accelerator pedal all the way to the floor and hold
it.
[TO04600(ALL)12/95]2.
Turn the ignition key to the START position.
[TO04700(ALL)12/95]3.
Release the ignition key when the engine starts.
[TO04800(ALL)12/95]4.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
*
[TO04900(ALL)03/96]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchin the index.
File:08cdtoo.ex
Update:Thu Sep 12 11:03:39 1996

Driving
129
*
[GF03100(ALL)01/96]
Always check the Brake Warning Light each time you start your
engine. Driving with the parking brake on will cause the brakes
to wear out quickly and will reduce the fuel economy.
%*
[GF03200(ALL)02/96]
Traction Control (If equipped)
[GF03300(ALL)12/95]
The traction control system prevents the wheels from spinning
on slippery roads.
[GF03400(ALL)12/95]
Working with the anti-lock brake system, the traction control
system monitors the speed of the wheels as they roll over the
road surface. When a wheel starts to spin because of slippery
conditions, the traction control system slows the engine by
closing the throttle. At speeds below 35 mph (55 km/h) the
traction control system also applies the brake to the spinning
wheel.
[GF03500(ALL)12/95]
When the traction control system becomes active, the driver
may notice a very slight kick and then a hard resistance in the
accelerator pedal, and a mechanical noise. The traction control
system light on the instrument panel comes on or flashes on
and off during activation.
[GF03600(ALL)12/95]
The traction control system can be turned off manually by
pushing the T/C OFF button on the instrument panel to the left
of the steering wheel. The traction control system light will
remain on as a reminder that the system is turned off.
[GF03700(ALL)12/95]
Each time the vehicle is started, the traction control system will
automatically be on. When the ignition is turned to the ON
position, the traction control system light comes on for
approximately three (3) seconds.
[GF03800(ALL)12/95]
If the light does not come on when the ignition is turned to the
ON position or if it does not come on when the T/C OFF
button is pressed, have the system serviced by your dealer or a
qualified service technician as soon as possible to restore the
benefits of the traction control feature. You do not need to have
the vehicle towed in.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Driving
131
*
[GF04800(ALL)12/95]
To operate:
*
[GF04900(ALL)12/95]1.
Start the engine.
*
[GF05000(ALL)12/95]2.
Depress and hold the brake pedal.
*
[GF05100(ALL)12/95]3.
Move the gearshift lever out of P (Park).
%*
[GF05200(ALL)12/95]
Your vehicle is equipped with a Brake Shift Interlock safety
feature. This feature prevents the gearshift from being moved
from the P (Park) position until the brake pedal is depressed.
This feature is active when the ignition is in the ON position. If
the gearshift lever CANNOT be moved from P (Park) with the
brake pedal depressed:
*
[GF05300(ALL)12/95]1.
Turn the engine off and remove the ignition key.
[GF05400(ALL)12/95]2.
With the parking brake applied and the brake pedal
depressed, insert a screwdriver about 2" (5 cm) into the
square opening to the right of the gearshift at the base of the
console.
[GF05500(ALL)12/95]3.
Rotate the screwdriver point rearward.
[GF05600(ALL)12/95]4.
Push and hold the thumb button and move the gearshift.
[GF05700(ALL)12/95]5.
Remove the screwdriver when the gearshift moves from the
P (Park) position.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

132
[GF05800(ALL)12/95]
13-1/2 pica
art:0001264-C
Overriding the brake shift interlock
*
[GF05900(ALL)12/95]
The console-mounted gearshift will lock when you turn the key
to the LOCK position. When the gearshift is in any position
except P (Park), the ignition key cannot be turned to LOCK or
removed from the steering column. TO REMOVE THE KEY, the
gearshift levermustbe in P (Park).
*
[GF06000(ALL)01/96]
Once the gearshift is secure in the desired position, release the
brake pedal and use the accelerator as necessary.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Driving
135
*
[GF07500(ALL)03/96]
When to use 2 (Second)
[GF07600(ALL)12/95]
When your vehicle is in 2 (Second), it automatically starts off in
second gear. Use 2 (Second) to help drive up moderately steep
hills or restart from a standstill on slippery roads. It prevents
the transaxle from frequently shifting up and down. It also
gives more engine braking than D (Drive) (with Transaxle
Control Switch activated) when going down hills.
[GF07700(ALL)12/95]
Do not go faster than 55 mph (90 km/h) in this gear. You can
upshift from 2 (Second) into D (Overdrive) at any speed.
*
[GF07800(ALL)01/96]
When to use 1 (First)
[GF07900(ALL)12/95]
This position limits the transaxle to first gear. It helps brake the
vehicle when going down hills where 2 (Second) is not
sufficient.
[GF08000(ALL)12/95]
Do not go faster than 38 mph (60 km/h) in this gear. You can
upshift from 1 (First) to 2 (Second) or from 1 (First) to D
(Overdrive) at any speed.
*
[GF08100(ALL)03/96]
P (Park)
*
[GF08200(ALL)01/96]
Always come to a complete stop before you shift into P (Park).
Make sure that the gearshift is securely latched in P (Park). This
locks the transaxle and prevents the front wheels from rotating.
*
[GF08300(ALL)03/96]
RWARNING
Always set the parking brake fully and make sure the
gearshift is latched in P (Park). Turn off the ignition
whenever you leave your vehicle.
*
[GF08400(ALL)01/96]
RWARNING
Never leave your vehicle unattended while it is running.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

150
[ER00700(ALL)04/96]
13-1/2 pica
art:0000530-D
The left-hand trim panel in the driver's footwell
*
[ER00800(ALL)03/96]
RWARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
*
[ER00900(ALL)03/96]
If your engine cranks but does not start after a collision or
substantial jolt:
*
[ER01000(ALL)01/96]1.
Turn the ignition key to the OFF position.
*
[ER01100(ALL)03/96]2.
Check under the vehicle for leaking fuel.
*
[ER01200(ALL)01/96]3.
If you do not see or smell fuel, push the red reset button
down. If the button is already set, you may have a different
mechanical problem.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996