brake light FORD CONTOUR 1997 2.G Owners Manual

Instrumentation
13
%*
[IS02600(ALL)01/96]
Brake System Warning Light
*
[IS02700(ALL)03/96]
The warning light for the brakes can show two things Ð that
the parking brake is not fully released, or that the brake fluid
level is low in the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by a qualified service
technician.
[IS02800(ALL)12/95]
6 pica art:0000971-D*
[IS02900(ALL)12/95]
This light comes on when the parking brake is set, or if it is not
set, it comes on briefly when you turn the ignition to the
START position. It normally goes off shortly after the engine
starts and you release the parking brake. If the light stays on
after you have fully released the parking brake, have the
hydraulic brake system serviced by your dealer or a qualified
service technician.
*
[IS03000(ALL)03/96]
RWARNING
The BRAKE light indicates that the brakes may not be
working properly. Have the brakes checked immediately.
File:03cdiso.ex
Update:Thu Sep 12 10:58:17 1996

Instrumentation
21
%*
[IS08900(ALL)03/96]
Odometer
*
[IS09000(ALL)01/96]
The odometer tells you the total number of miles (kilometers)
your vehicle has been driven.
%*
[IS09100(ALL)01/96]
Trip Odometer
[IS09200(ALL)12/95]
The trip odometer tells you how many miles (kilometers) your
vehicle has been driven since the last reset. Press the reset
control to return the trip odometer to zero.
[IS09300(O )12/95]
Sport Cluster
*
[IS09400(O )12/95]
The sport cluster has basically the same standard warning lights
and gauges as the standard cluster, with the following
additional features:
%*
[IS09500(ALL)03/96]
Tachometer
*
[IS09600(ALL)01/96]
The tachometer displays the approximate engine revolutions per
minute (rpm), or how fast the engine is running.
*
[IS09700(ALL)03/96]
If you drive with the tachometer in the red zone, you may
damage the engine.
%*
[IS09800(ALL)01/96]
Anti-lock Brake System Warning Light (If equipped)
[IS09900(ALL)12/95]
Your vehicle may have an Anti-lock Brake System feature. If it
does, check the Anti-lock Brake System light each time you start
the engine. If it stays on longer than three (3) seconds, shut off
the engine and restart. If it stays on, that means the Anti-lock
Brake feature is not working and should be serviced
immediately to restore the benefits of the Anti-lock feature.
Normal braking is not affected unless the brake warning light is
also lit.
[IS10000(ALL)12/95]
The Anti-Lock Brake System has self-check capabilities. As
described above, the system turns on the anti-lock light each
time you start your engine. After the engine is started and the
anti-lock light turns off, the system performs another test the
first time the vehicle reaches 5 mph (8 km/h) (between 12 and
File:03cdiso.ex
Update:Thu Sep 12 10:58:17 1996

Controls and Features
53
%*
[CF06000(ALL)08/95]
Fog Lamps (If equipped)
[CF06100(ALL)12/95]
The fog lamps act as a supplement to the low beam headlamps
under limited visibility conditions such as rain, snow, dust or
fog.
[CF06200(ALL)12/95]
The fog lamps operate only when the low beam headlamps are
on. To operate the fog lamps, turn the headlamp control knob
to the second position (headlamps on) and pull the knob out.
An indicator lamp will glow when the fog lamps are on.
[CF06300(ALL)12/95]
To turn off, push the headlamp control knob in.
*
[CF06400(ALL)03/96]
To maximize fog lamp bulb life, it is recommended that the fog
lamp switch be turned off after each use prior to turning off the
headlamps.
%*
[CF06500(ALL)03/96]
Daytime Running Light System
*
[CF06600(ALL)03/96]
(Canadian vehicles only)
*
[CF06700(ALL)01/96]
The Daytime Running Light (DRL) system is designed to turn
the high beam headlamps on, with a reduced light output and
without illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates when all of the
following conditions are met:
[CF06750(ALL)04/96]
n
The vehicle's parking brake is fully released.
[CF06800(ALL)04/96]
n
The vehicle is ªrunning.º
[CF06900(ALL)04/96]
n
The headlamp system is in the OFF position.
*
[CF07000(ALL)03/96]
The high beam indicator light on the instrument cluster will not
be on.
[CF07100(ALL)12/95]
A flashing high beam light in the instrument cluster indicates a
failure in the DRL system circuit, like a burnt bulb or fuse.
File:05cdcfo.ex
Update:Fri Sep 13 08:48:17 1996

Controls and Features
57
[CF09900(ALL)12/95]
ACCESSORY allows some of your vehicle's electrical accessories
to operate while the engine is not running. For example, you
can use ACCESSORY to turn on the radio without starting the
engine.
*
[CF10000(ALL)01/96]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[CF10100(ALL)01/96]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
%*
[CF10200(ALL)03/96]
Removing the Key From the Ignition
[CF10300(ALL)04/96]
Procedures for removing your key from the ignition vary,
depending on whether your vehicle has an automatic or manual
transaxle.
[CF10400(ALL)04/96]
If your vehicle has an automatic transaxle:
*
[CF10500(ALL)01/96]1.
Put the gearshift lever in P (Park).
*
[CF10600(ALL)01/96]2.
Set the parking brake fully.
[CF10700(ALL)12/95]3.
Rotate the ignition key to the LOCK position.
[CF10800(ALL)12/95]4.
Remove the key from the ignition.
File:05cdcfo.ex
Update:Fri Sep 13 08:48:17 1996

117
Starting
%*
[TO00200(ALL)01/96]
Fuel-Injected Engines
*
[TO00300(ALL)01/96]
When starting a fuel-injected engine,the most important thing
to remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your
Enginein this chapter for details about when to use the
accelerator while you start your vehicle.
*
[TO00400(ALL)01/96]
Starting Your Vehicle
%*
[TO00500(ALL)01/96]
Preparing to Start Your Vehicle
*
[TO00600(ALL)02/96]
RWARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open
the garage door before you start the engine.
*
[TO00700(ALL)01/96]
Before you start your vehicle, do the following:
*
[TO00800(ALL)01/96]1.
Make sure all occupants in the vehicle buckle their safety
belts. SeeSafety Restraintsin the Index for more details.
*
[TO00900(ALL)12/95]2.
Make sure your headlamps and other accessories are turned
off and the parking brake is set.
[TO01000(ALL)12/95]3.
If you have a manual transaxle,make sure that the parking
brake is fully set, push the clutch pedal to the floor, and put
the gearshift into Neutral before you turn the key.
(Remember, the starter will operate only if the clutch pedal
is pushed all the way to the floor.)
[TO02000(ALL)12/95]
If you have an automatic transaxle,make sure that the
gearshift is in P (Park) and the parking brake is set before
you turn the key.
*
[TO02100(ALL)02/96]
Before you start your vehicle, you should test the warning lights
on the instrument panel to make sure that they work. Refer to
theInstrumentationchapter.
File:08cdtoo.ex
Update:Thu Sep 12 11:03:39 1996

118
%*
[TO02200(ALL)01/96]
Starting Your Engine
*
[TO02300(ALL)01/96]
To start your engine:
*
[TO02400(ALL)01/96]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[TO02500(ALL)01/96]2.
Keep your foot on the brake pedal and turn the ignition key
to the ON position.
*
[TO02600(ALL)01/96]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[TO02700(ALL)01/96]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[TO02800(ALL)01/96]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
%*
[TO02900(ALL)01/96]
For a cold engine:
[TO03000(ALL)12/95]
2.0L engine:
[TO03100(ALL)12/95]
n
At temperaturesbelow-10ÊF (-23ÊC):Turn the key to ON,
crank the engine and depress the accelerator about 1/4 of
the way down and hold that position forfive (5) seconds.If
the engine fails to start, continue to crank with the
accelerator depressed about 1/4 of the way down and hold
that position until the engine starts.DO NOT crank for
more than 30 seconds,or you could damage the starter. If
the engine fails to start on the first try, turn the key to OFF
and wait two (2) minutes before trying again. Allow engine
to warm up for a few minutes before putting transaxle into
gear.
File:08cdtoo.ex
Update:Thu Sep 12 11:03:39 1996

126
*
[GF01400(ALL)01/96]
Do not drive with your foot resting on the brake pedal; you
will wear out the linings and increase your vehicle's stopping
distance. Brake rotor damage may also eventually occur.
*
[GF01500(ALL)02/96]
NOTE: If you are driving down a long or steep hill, shift to a
lower gear and do not apply your brakes
continuously. If you apply your brakes continuously,
they may overheat and become less effective.
%*
[GF01600(ALL)01/96]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified service technician.
*
[GF01700(ALL)01/96]
Anti-lock Brake System (If equipped)
*
[GF01800(ALL)12/95]
Your vehicle may come with the optional anti-lock brake
system. Whenever your wheels start to lock (which could result
in a skid) the anti-lock brake system prevents the lock-up by
automatically releasing and re-applying the brakes. The brake
pedal will pulsate as a result of the automatic releasing and
re-applying of the brakes. In spite of this improvement in
braking performance, you should continue to be cautious in all
hazardous driving situations, especially when driving on
hazardous road surfaces. Even with your anti-lock brake system,
you may not have total control of your vehicle when braking on
roads with loose surfaces such as snow or gravel, holes in the
pavement, or alternating patches of slippery and dry surfaces.
*
[GF01900(ALL)01/96]
If the brake pedal is applied while the vehicle is driven over
uneven road surfaces, the ABS may cycle and the driver may
sense a pulsation in the brake pedal, accompanied by a slight
up and down movement of the pedal height and a clicking
sound. This may also happen when driving on an inclined
surface such as a driveway while making a sharp turn. This is a
normal condition.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Driving
127
[GF02000(ALL)12/95]
Your vehicle may have an Anti-lock Brake System feature. If it
does, check the Anti-lock Brake System light each time you start
the engine. If it stays on longer than three (3) seconds, shut off
the engine and restart. If it stays on, that means the Anti-lock
Brake feature is not working and should be serviced
immediately to restore the benefits of the Anti-lock feature.
Normal braking is not affected unless the brake warning light is
also lit.
[GF02100(ALL)12/95]
The Anti-lock Brake System has self-check capabilities. As
described above, the system turns on the anti-lock light each
time you start your engine. After the engine is started and the
anti-lock light turns off, the system performs another test the
first time the vehicle reaches 5 mph (8 km/h) (12 mph
[20 km/h] for vehicles equipped with the traction control
system). The system turns on the ABS pump motor for
approximately 1/2 second. At this time, a mechanical noise may
be heard and felt. This is a normal part of the self-check feature.
If a malfunction is found during this check the anti-lock light
will come on.
*
[GF02200(ALL)01/96]
Ford Motor Company has not found any negative effects of
mobile radio transmitting equipment installed on vehicles with
the ABS system providing that the radio is installed according
to the radio manufacturer's instructions. However, if you have
had a mobile radio transmitter installed and the ABS light
comes on (at any time other than immediately after turning the
key to the ON position) have your mobile radio dealer inspect
the radio installation. Also, if the ABS system is activated other
than during maximum braking, have your mobile radio
installation checked.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

128
%*
[GF02300(ALL)01/96]
Parking Brake
*
[GF02400(ALL)03/96]
The parking brake should be used whenever you park your
vehicle.
*
[GF02500(ALL)01/96]
The parking brake lever is located between the front seats. To
set the parking brake, put your foot on the brake pedal while
pulling the parking brake handle fully and firmly upward.
*
[GF02600(ALL)01/96]
To release the parking brake, put your foot on the brake pedal,
pull the handle upward and push the button. Then lower the
handle to the released position while holding the button in.
*
[GF02700(ALL)01/96]
RWARNING
Always set the parking brake fully and make sure that
the gearshift is securely latched in P (Park) (automatic
transaxle) or in 1 (First) (manual transaxle).
*
[GF02800(ALL)01/96]
RWARNING
To prevent personal injury, do not release the parking
brake while outside the vehicle.
*
[GF02900(ALL)02/96]
RWARNING
If the parking brake is fully released, but the Brake
System light remains on, have the brakes checked
immediately. They may not be working properly.
*
[GF03000(ALL)03/96]
The parking brake is not designed to stop a moving vehicle, but
you can use the parking brake to stop your vehicle in an
emergency if the normal brakes fail. However, since the parking
brake applies only the rear brakes, the stopping distance will
increase greatly and the handling of your vehicle will be
adversely affected.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Driving
129
*
[GF03100(ALL)01/96]
Always check the Brake Warning Light each time you start your
engine. Driving with the parking brake on will cause the brakes
to wear out quickly and will reduce the fuel economy.
%*
[GF03200(ALL)02/96]
Traction Control (If equipped)
[GF03300(ALL)12/95]
The traction control system prevents the wheels from spinning
on slippery roads.
[GF03400(ALL)12/95]
Working with the anti-lock brake system, the traction control
system monitors the speed of the wheels as they roll over the
road surface. When a wheel starts to spin because of slippery
conditions, the traction control system slows the engine by
closing the throttle. At speeds below 35 mph (55 km/h) the
traction control system also applies the brake to the spinning
wheel.
[GF03500(ALL)12/95]
When the traction control system becomes active, the driver
may notice a very slight kick and then a hard resistance in the
accelerator pedal, and a mechanical noise. The traction control
system light on the instrument panel comes on or flashes on
and off during activation.
[GF03600(ALL)12/95]
The traction control system can be turned off manually by
pushing the T/C OFF button on the instrument panel to the left
of the steering wheel. The traction control system light will
remain on as a reminder that the system is turned off.
[GF03700(ALL)12/95]
Each time the vehicle is started, the traction control system will
automatically be on. When the ignition is turned to the ON
position, the traction control system light comes on for
approximately three (3) seconds.
[GF03800(ALL)12/95]
If the light does not come on when the ignition is turned to the
ON position or if it does not come on when the T/C OFF
button is pressed, have the system serviced by your dealer or a
qualified service technician as soon as possible to restore the
benefits of the traction control feature. You do not need to have
the vehicle towed in.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996