ECU FORD E SERIES 1996 4.G User Guide

51
*
[SR16415(BEF )06/95]
8. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode,
Figure 8.
*
[SR16420(BEF )06/95]
half page art:0011245-B
Checking the retractor
*
[SR16425(BEF )06/95]
9. Check to make sure that the child seat is
properly secured prior to each use. If the
retractor is not locked, repeat steps 4
through 7.
*
[SR16430(BEF )06/95]
To remove the retractor from automatic lock
mode, allow webbing to retract fully to its
stowed position and the retractor will
automatically switch back to the vehicle sensitive
locking mode for normal adult usage.
File:03ltsre.ex
Update:Wed Apr 17 08:51:22 1996

52 [SR16440(BEF )04/95]Installing a Child Safety Seat at the Rear
Center Seating Position with Locking
Adjustable Lap Belt
[SR16450(BEF )04/95]
1. Lengthen the lap belt. To lengthen the belt,
hold the tongue so that its bottom is
perpendicular to the direction of webbing
while sliding the tongue up the webbing.
[SR16455(BEF )04/95]
2. Place the child safety seat in the center
seating position.
[SR16460(BEF )04/95]
3. Route the tongue and webbing through the
child seat according to the child seat
manufacturer's instructions.
[SR16465(BEF )04/95]
4. Insert the belt tongue into the proper buckle
for the center seating position until you hear
a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
[SR16470(BEF )04/95]
5. Push down on the child seat while pulling
on the loose end of the lap belt webbing to
tighten the belt.
[SR16475(BEF )04/95]
6. Before placing the child into child seat,
forcibly tilt the child seat from side-to-side
and in forward directions to ensure that the
seat is held securely in place. If the child
seat moves excessively, repeat steps 5
through 6, or properly install the child seat
in a different seating position.
File:03ltsre.ex
Update:Wed Apr 17 08:51:22 1996

56 %
*
[ST02800( ALL)05/95]
If the key is stuck in the LOCK position, move
the steering wheel left or right until the key
turns freely.
%*
[ST02900( ALL)03/95]
ACCESSORY allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[ST03025(BEF )03/91]
Ignition Key Buzzer or Chime
*
[ST03050(BEF )03/91]
The buzzer or chime will sound if you open the
driver's door while the key is in the ignition.
Never leave your vehicle unattended with the
key in the ignition.
%*
[ST03075( ALL)02/95]
Removing the Key From the Ignition
[ST03125( E M)03/91]
Procedures for removing your key from the
ignition are as follows:
[ST03350( E M)03/91]
Your vehicle's gearshift lever is mounted on
the column:
*
[ST03400( ALL)06/95]
1. Put the gearshift in P (Park).
*
[ST03500( ALL)03/91]
2. Set the parking brake fully before removing
your foot from the service brake. (This will
avoid ªbindingº or ªloadingº the park gear
if you park on a grade.)
*
[ST03600( ALL)03/95]
3. Turn the ignition key to LOCK.
*
[ST03700( ALL)03/95]
4. Remove the key.
*
[ST04625( E M)06/95]
RWARNING
Always set the parking brake fully and
make sure the gearshift is securely latched
in P (Park).
File:04ltste.ex
Update:Wed Apr 17 08:49:38 1996

73
*
[LG04675( ALL)05/95]
An example of a condition which corrects itself
occurs when an engine running out of fuel
begins to misfire. In this case, the Check Engine
Warning Light may turn on and will then set a
Diagnostic Trouble Code indicating that the
engine was misfiring while the last of the fuel
was being consumed. After refueling, the Check
Engine Warning Light will turn off after the
vehicle has completed three consecutive warm
up cycles without a misfire condition occurring.
A warm up cycle consists of engine start from a
cold condition (engine at ambient temperature)
and running until the engine reaches normal
operating temperature.
*
[LG04700( ALL)05/95]
On the fourth engine start up, the Check Engine
Warning Light will turn off as soon as the
engine begins to crank. It is not necessary to
have the engine serviced.
*
[LG04725( ALL)05/95]
Under certain conditions, the Check Engine
Warning Light may come on if the fuel cap is
not properly installed. If the Check Engine
Warning Light comes on and you suspect that
the fuel cap is not properly installed, pull off the
road as soon as it is safely possible and turn off
the engine. Remove and replace the fuel cap,
making sure it is properly seated.
*
[LG04750( ALL)05/95]
After completing the three consecutive warm up
cycles and on the fourth engine start up, the
Check Engine Warning Light should turn off. If
the light does not go off after the fourth engine
restart, have your vehicle serviced by your
dealer or a qualified technician.
File:05ltlge.ex
Update:Wed Apr 17 08:49:15 1996

124
*
[FV22901(BEF )03/91]
Using the Power Windows (If equipped)
*
[FV23001(BEF )06/95]
Each door has a power control that opens and
closes the window on that door. The driver's
door has a master control switch that operates
both front door windows. You must place the
ignition switch in the ON or ACC position to
use your power window controls.
*
[FV23501(BEF )05/95]
RWARNING
Do not let children play with the power
windows. They may seriously hurt
themselves. Make sure occupants are clear
of the window(s) before closing.
*
[FV23800(BEF )05/95]
quarter page art:0020203-C
Master control switch
*
[FV24101(BEF )01/95]
Seats
%*
[FV24801(BEF )05/90]
Adjusting the Front Seat Manually
*
[FV24901(BEF )06/95]
To move the front seat forward or rearward:
*
[FV25001(BEF )06/95]
1. Find the adjustment lever at the lower left
corner of the front seat.
*
[FV25101(BEF )06/95]
2. Push the lever to the left to unlatch the seat.
*
[FV25201(BEF )06/95]
3. Move the seat to the desired position.
*
[FV25301(BEF )06/95]
4. Release the lever to latch the seat in its new
position. Make sure the seat locks securely in
place.
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

127 [FV32101( E )12/91]
3. Remove the seat from the vehicle.
*
[FV32200( E )12/91]
To install the rear bucket seat:
[FV32400( E )12/91]
1. Lift the seat assembly into the vehicle and
position the seat to the floor mount.
[FV32600( E )02/92]
2. Engage the four seat pins into their
respective floor mount holes and push the
seat toward the left hand side of the vehicle
to fully engage.
[FV32700( E )02/92]
one third page art:0020916-B
Installing the quick release rear captains chair
[FV33001( E )12/91]
3. Push the seat latch handle downward to a
full stop. This locks the seat in position.
[FV33101( E )12/91]
4. Before you engage the safety belt, be sure it
is not twisted. Remove any twist, then insert
the tongue end of the detachable anchor into
the detachable anchor until you hear a
ªsnapº and feel the latch engage.
*
[FV33201( E )05/95]
RWARNING
Check to see that the seat is latched
securely in position. Keep floor area free
of objects that would prevent proper seat
engagement. Never attempt to adjust the
seat latch while the vehicle is in motion.
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

136 [FV38001( E )02/92]
two third page art:0020917-BQuick seat release Ð bed seat
[FV38101( E )01/89]
RWARNING
Keep striker area free of foreign objects
that would prevent front and rear
retainers from engaging the strikers
properly.
*
[FV38201( E )05/93]
RWARNING
Before using the seat, make sure that the
latch hooks are securely locked around the
floor pins.
File:08ltfve.ex
Update:Wed Apr 17 08:47:13 1996

157
*
[AS06200(BEF )04/95]
NOTE: If after you insert a disc, the disc is
ejected and ªERRORº begins scrolling
in the display, remove the disc and
reinsert it right side up (label side up).
*
[AS06250(BEF )04/95]
The digital display on your CD player will
either show the track (selection) number or the
elapsed time. (The display mode can be selected
by pressing the ªCLOCKº button.) Indicators for
play (
a), stop (
X) and compression on (ªCº)
are also in the display. (These features are
described later.)
*
[AS06300(BEF )04/95]
Once a disc is inserted, operation of the CD
player will override that of the radio.
*
[AS06350(BEF )04/95]
NOTE: The volume, bass, treble, balance and
fader controls on the radio are also
used with the CD player. Refer to
earlier operating instructions on these
controls.
*
[AS06400(BEF )04/95]
How to insert a disc and begin play
*
[AS06450(BEF )04/95]
Insert one disc,label side upinto the disc
opening. When inserted, the disc automatically
loads into the unit and play starts at the
beginning of the first track (selection).
*
[AS06500(BEF )06/95]
When the disc reaches the end, the disc player
automatically returns to the beginning of the
disc and resumes playing.
*
[AS06550(BEF )04/95]
NOTE: Once a disc is inserted, the disc
opening is secured to prevent the
accidental insertion of a second disc.
File:09ltase.ex
Update:Wed Apr 17 08:44:51 1996

196
*
[DR01000( EF )06/93]
one third page art:0020129-C
The positions of the column-mounted gearshift
*
[DR01100( EF )05/95]
RWARNING
Hold the brake pedal down while you
move the gearshift lever from position to
position. If you do not hold the brake
pedal down, your vehicle may move
unexpectedly and injure someone.
*
[DR01200( EF )01/95]
Once you place the gearshift securely into
position, gradually release the brake pedal and
use the accelerator as necessary.
%*
[DR01210( EF )01/95]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[DR01220( EF )01/95]
1. Apply the parking brake.
*
[DR01230( EF )01/95]
2. Remove the key.
*
[DR01240( EF )01/95]
3. Insert the key and rotate one position
clockwise (ignition in the OFF position).
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996

198
*
[DR02100( EF )01/95]
When to use 1 (Low)
*
[DR02200( EF )06/92]
Use 1 (Low) to drive up steep grades and to
provide maximum engine braking on hilly roads.
Upshifts from 1 (Low) can be made by manually
shifting to 2 (Second) or D (Drive). Selection of 1
(Low) gear provides only First gear operation at
start-up. When driving, manually shifting to 1
(Low) will result in downshifts to Second gear
or First gear depending on vehicle speed.
*
[DR02250( EF )12/91]
NOTE: Do not drive faster than 30 mph
(48 km/h) in this gear.
*
[DR02300( EF )01/95]
P (Park)
*
[DR02400( EF )03/94]
Always come to a complete stop before you shift
into P (Park). This position locks the
transmission and prevents the rear wheels from
turning. To securely latch the gearshift in the P
(Park) position, pull it toward you, push it
completely counterclockwise against the stop,
and then push it toward the instrument panel.
*
[DR02450( EF )03/94]
The gearshift is securely latched in P (Park) if
you cannot rotate it in a clockwise direction
without lifting it toward you.
*
[DR02500( EF )06/95]
RWARNING
Always set the parking brake fully and
make sure the gearshift is securely latched
in P (Park).
*
[DR02600( EF )06/95]
RWARNING
Never leave your vehicle unattended
while it is running.
File:10ltdre.ex
Update:Wed Apr 17 08:44:07 1996