battery FORD ESCORT 1996 7.G Owners Manual

121 [LG03550(ALL)08/95]
one inch art:0000837-A
The brake system and parking brake light
*
[LG03600(ALL)05/95]
RWARNING
The BRAKE light indicates that the brakes
may not be working properly. Have the
brakes checked immediately.
%*
[LG03800(ALL)01/95]
Charging System Light
*
[LG03900(ALL)03/95]
This light indicates that your battery is not being
charged and that you need to have the electrical
system checked.
*
[LG04300(ALL)07/95]
This light comes on every time you turn the
ignition to the ON or START position (engine
off). The light should go off when the engine
starts and the alternator begins to charge.
*
[LG04400(ALL)01/95]
If the light stays on or comes on when the
engine is running, have the electrical system
checked as soon as possible.
[LG04500(ALL)12/89]
one inch art:0000838-A
The charging system light
File:05ctlge.ex
Update:Tue Sep 19 14:44:43 1995

162
%*
[SC05320(ALL)03/95]
Hazard Flasher
[SC05340(ALL)08/95]
half page art:0070197-D
Using the hazard flasher switch
*
[SC05360(ALL)03/95]
The hazard flasher serves as a warning to other
drivers to be careful when approaching or
passing your vehicle.
*
[SC05400(ALL)08/95]
The flashers work whether your vehicle is
running or not. The flashers work for up to two
hours when the battery is fully charged and in
good condition without draining the battery
excessively. If the flashers run for longer than
two hours or if the battery is not fully charged,
the battery power can be drained.
File:07ctsce.ex
Update:Tue Sep 19 14:47:40 1995

216
*
[AS23900(ALL)08/95]
NOTE: If the vehicle's battery is disconnected,
the clock and station memory preset
buttons will need to be reset.
*
[AS24000(ALL)08/95]
Adjusting the tone balance and speaker
output of your radio
*
[AS24100(ALL)08/95]
q
Increasing or decreasing bass response
[AS24250(ALL)06/95]
Push the ªAUDIOº button repeatedly until
the display reads ªBASS.º Push the ª+º side
of the ªVOLUMEº button to increase bass
(more ªlowsº), and push the ª-º side to
decrease bass (less ªlowsº).
*
[AS24300(ALL)08/95]
q
Increasing or decreasing treble response
[AS24450(ALL)06/95]
Push the ªAUDIOº button repeatedly until
the display reads ªTREB.º Push the ª+º side
of the ªVOLUMEº button to increase treble
(more ªhighsº), and push the ª-º side to
decrease treble (less ªhighsº).
*
[AS24500(ALL)08/95]
Speaker features and operation
*
[AS24600(ALL)08/95]
q
Adjusting speaker balance
[AS24750(ALL)06/95]
Balance control allows you to adjust the
sound distribution between the right and left
speakers. Push the ªAUDIOº button
repeatedly until the display reads ªBAL.º
Push the ª+º side of the ªVOLUMEº button
to shift the sound to the right speakers, and
push the ª-º side to shift the sound to the
left speakers.
*
[AS24800(ALL)08/95]
q
Adjusting speaker fader
[AS24950(ALL)06/95]
Fade control allows you to adjust the sound
distribution between the front and rear
speakers. Push the ªAUDIOº button
repeatedly until the display reads ªFADE.º
Push the ª+º side of the ªVOLUMEº button
to shift the sound to the front speakers, and
push the ª-º side to shift the sound to the
rear speakers.
File:09ctase.ex
Update:Tue Sep 19 14:51:59 1995

225 [DR05020(ALL)07/93]
Your vehicle has a special shift-lock safety
feature which prevents you from shifting out of
P (Park) without the brake pedal depressed. To
shift the transaxle out of the P (Park) position,
the ignition must be in the ON position, the
battery must be supplying electrical power, and
your foot must be pressing on the brake pedal.
[DR05030(ALL)01/92]
In the unlikely event that you cannot move the
selector lever from the P (Park) position with the
brake pedal depressed, continue depressing the
brake. Then:
*
[DR05035(ALL)06/95]
1. Remove the shift-lock override cap with a 1ª
or longer screwdriver.
[DR05038(ALL)02/94]
half page art:0070192-B
Shift-lock override
*
[DR05040(ALL)03/93]
2. Insert the screwdriver into the shift-lock
override opening and push the screwdriver
handle down.
File:10ctdre.ex
Update:Tue Sep 19 14:53:34 1995

243
Roadside Emergencies
%*
[RE00380(ALL)03/95]
Jump-Starting Your Vehicle
[RE00390(ALL)01/92]
Your vehicle's battery may die if you leave the
lights or any electrical equipment on after you
turn the engine off. If this happens, you may be
able to jump-start from a booster battery to start
your vehicle.
*
[RE00400(ALL)02/95]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[RE00500(ALL)02/95]
RWARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
%*
[RE00600(ALL)06/95]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
%*
[RE00700(ALL)07/95]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995

244
*
[RE00710(ALL)07/95]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[RE00900(ALL)05/95]
RWARNING
To avoid damage or injury, follow these
directions in the order they are given. If
in doubt, call for road service.
*
[RE01000(ALL)03/95]
Preparing Your Vehicle
*
[RE01100(ALL)03/95]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
*
[RE01200(ALL)03/95]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[RE01300(ALL)04/95]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01400(ALL)03/95]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
*
[RE01600(ALL)02/95]
5. Turn on the heater fan in both vehicles.
Turning on the fan helps protect the
electrical system from voltage surges. Turn
off all other switches and lights in both
vehicles to prevent possible damage to either
vehicle's electrical systems.
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995

245 %
*
[RE01700(ALL)05/95]
Connecting the jumper cables
*
[RE02500(ALL)03/95]
1. Connect one end of the first jumper cable to
the positive (+) terminal of the discharged
battery. (You can connect either jumper cable
to the positive (+) terminal, as long as you
use the same cable for both positive
terminals.) Most jumper cables have a red
cable and a black cable. The red cable is
generally used for the positive terminals and
the black for the negative ones.
*
[RE02600(ALL)04/95]
2. Connect the other end of the first cable to
the positive (+) terminal of the booster
battery.
*
[RE02700(ALL)07/95]
3. Connect one end of the second cable to the
negative (S) terminal of the booster battery
Ð NOT to the discharged battery.
*
[RE02800(ALL)04/95]
4. Connect the other end of the second cable to
a good metallic surface on the engine or
frame of the disabled vehicle.
*
[RE02900(ALL)07/95]
RWARNING
Do not connect the end of the second
cable to the negative (S) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995

246 [RE02910(ALL)12/91]
three fourths page art:0000885-BThe battery with jumper cables (1.8L engine)
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995

247 [RE02920(ALL)12/91]
three fourths page art:0000889-A
The battery with jumper cables (1.9L engine)
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995

248
*
[RE03400(ALL)03/95]
Jump-Starting
*
[RE03600(ALL)03/95]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[RE03700(ALL)03/95]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[RE03800(ALL)03/95]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
%*
[RE03900(ALL)03/95]
Removing jumper cables
*
[RE04000(ALL)03/95]
1.Always remove the jumper cables in the
reverse order.Remove the negative (S) end
of the jumper cable from the metallic surface
on the engine or frame of the disabled
vehicle.
*
[RE04100(ALL)06/95]
2. Remove the negative (S) cable from the
booster battery.
*
[RE04200(ALL)06/95]
3. Remove the positive (+) cable from the
booster battery.
*
[RE04300(ALL)05/95]
4. Remove the other end of the positive (+)
cable from the discharged battery.
*
[RE04400(ALL)04/95]
After the vehicle is started, let it idle for a while
to let the engine ªrelearnº its idle conditions.
Drive it around for a while with all electrical
accessories turned off to let the battery recharge.
You may need to use a battery charger to fully
recharge the battery.
*
[RE04450(ALL)03/95]
If you need to replace your battery, seeBattery
in theServicing Your Vehiclechapter.
File:12ctree.ex
Update:Tue Sep 19 14:55:16 1995