clock FORD ESCORT 1997 7.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: ESCORT, Model: FORD ESCORT 1997 7.GPages: 191, PDF Size: 2.02 MB
Page 112 of 191
Number Fuse amperage
ratingCircuits protected
9 Meter 10 amp Backup lamps, shift
lock, gauges, speed
control, turn signals,
key-in-ignition
reminder chime
10 Wiper 20 amp Windshield wipers
and washer
11 (Rear wiper) 10 amp Rear wiper and
washer
12 Hazard 15 amp Hazard flashers, turn
signals
13 Room 10 amp Clock, interior lamp,
luggage compartment
lamp, safety belt
warning chime, radio
power
14 Engine 15 amp Engine control system
15 Mirrors 5 amp Power mirrors
16 Ð Ð Not used
17 Ð Ð Not used
18 (Fog) 10 amp Daytime running
lamps / fog lamps
19 Ð Ð Not used
20 Cigar 20 amp Cigar lighter
21 (Radio) 15 amp Radio (Premium
sound)
Roadside emergencies
112
Page 118 of 191
7. Loosen the remaining wheel lug
nuts with the lug wrench about
one half turn counterclockwise.
8. Position the jack at the jack
notch closest to the wheel.
9. Insert the jack handle and raise
the vehicle until the tire just clears
the ground.
10. Remove the wheel lug nuts and
flat tire, and install the spare with
the ``temporary use'' label facing
outward.
11. Install the same metric wheel
lug nuts as removed and tighten
until snug.
Roadside emergencies
118
Page 137 of 191
2. When the engine is cool, wrap
a thick cloth around the cap and
turn it slowly, counterclockwise
to the first stop.
3. Step back while the pressure
releases.
4. When you are sure that all the
pressure has been released, use
the cloth to press the cap down,
turn it counterclockwise, and
remove it.
Use Ford Premium Engine Coolant
E2FZ-19549-AA (in Canada,
Motorcraft CXC-8-B) or an
equivalent premium engine coolant
that meets Ford Specification
ESE-M97B44-A. Ford Premium
Engine Coolant is an optimized
formula that will protect all metals
and rubber elastomers used in
Ford cooling systems for 4 years or
50,000 miles (80,000 km).
Do not use alcohol or methanol
antifreeze or any engine coolants
mixed with alcohol or methanol
antifreeze. Do not use
supplemental coolant additives in
your vehicle. These additives may
harm your engine cooling system.
The use of an improper coolant
may void the warranty of your
vehicle's engine cooling system.
Recycled Engine Coolant
Ford Motor Company recommends
that Ford and Lincoln-Mercury
dealers use recycled engine
coolant produced by
Ford-approved processes. Not all
coolant recycling processes
Maintenance and care
137
Page 145 of 191
of your vehicle may be adversely
affected until the idle is
eventually relearned.
²If the battery has been
disconnected or a new battery
has been installed, the clock and
preset radio stations must be
reset once the battery is
reconnected.
²Always dispose of used
automotive batteries in a
responsible manner. Follow your
community's standards for
disposal. Call your local
recycling center to find out
more about recycling automotive
batteries.
CHECKING AND CHANGING
YOUR AIR FILTER
If the vehicle is operated in very
dusty or sandy areas, replace the
filter more often than the
recommended intervals.
Do not drive without an air
filter; this could result in
excessive engine wear.
Maintenance and care
145
Page 162 of 191
Headlamps
To change the headlamp bulbs:
1. Be sure that the headlamp knob
is in the OFF position.
2. Open the hood and find the
headlamp socket.
3. Remove the protective dust
shield housing by turning the
shield counterclockwise.
4. Remove the bulb retaining ring
by rotating it counterclockwise
(when viewed from the rear).
5. Disconnect the electrical
connector and remove the bulb by
pulling it straight out.
6. Replace the bulb by pushing a
new one straight in with the bulb's
plastic base facing upward. You
may need to turn the bulb slightly
to align the grooves in the plastic
base with the tabs in the bulb
socket.
7. Slip the bulb retaining ring over
the plastic base and lock the ring
by rotating it clockwise until it
snaps.
8. Reconnect electrical connector.
9. Replace the housing protective
dust shield and lock the shield by
rotating clockwise until it locks
into position.
Maintenance and care
162
Page 167 of 191
Tail lamps / Backup lamps
(sedan)
The tail lamp assemblies and the
backup bulb assemblies are located
in the same portion of the vehicle
rear, one just below the other.
Follow the same steps to replace
either bulb.
1. Open the trunk lid to expose the
tail lamp assembly. Remove the
two screws from the front of the
lamp.
2. The tail lamp has hidden
fasteners which can be disengaged
by hitting the lamp, with your
hand, toward the side of the
vehicle.
3. Remove the socket that contains
the burned out bulb by rotating it
counterclockwise, then pulling it
out of the lamp assembly.
4. Pull the burned out bulb from
the socket and replace it with a
new bulb.
Maintenance and care
167
Page 168 of 191
5. Push the socket into the lamp,
then secure it by rotating it
clockwise.
6. Position the tail lamp on the
vehicle and gently hit the lens to
engage the clips. Replace the
screws.
Tail lamps/Backup lamps
(wagon)
To replace the tail lamp bulbs:
1. Open the liftgate to expose the
tail lamp assembly. Remove the
lens screws and pull the lens aside.
2. Remove the socket that contains
the burned out bulb by rotating it
counterclockwise, then pulling it
out of the lamp assembly.
3. Pull the burned out bulb from
the socket and secure a new bulb.
4. Push the socket into the lamp,
then secure it by rotating
clockwise.
5. Position the lamp on the vehicle
and replace the screws.
Maintenance and care
168
Page 170 of 191
2. Remove the bulb assembly form
the interior recess.
3. Twist the bulb counterclockwise
to remove it and secure a new
bulb.
4. Replace the bulb assembly in
the interior recess and replace the
access panel.
Interior overhead lamp
The interior overhead lamp is
located on the center of the ceiling
of the vehicle. To replace the
bulbs:
1. Remove the lamp lens by
applying pressure to both tabs at
the top of the lamp assembly and
pulling the lens down and off.
2. Pull the bulb to remove it and
secure a new bulb.
3. Replace the lamp lens by
applying pressure to both sides of
the lamp lens and popping the lens
up and on to the lamp assembly.
OFF DOOR ON
OFF DOOR ON
Maintenance and care
170
Page 174 of 191
Adjusting the horizontal aim
1. With the hood open, locate the
horizontal indicator and adjusting
screw.
2.Usea4mmwrench to turn the
horizontal adjusting screw until the
reference mark on the reflector
extension aligns with the ``O''
reference mark on the horizontal
indicator when viewed directly
from above.
3. When the horizontal aim has
been adjusted, close the headlamp
access panel.
Adjusting the vertical aim
1. Do not adjust the vertical aim
until after adjusting the horizontal
aim.
2. With the hood open, locate the
bubble level vertical aim indicator.
It is visible when viewed from
above the rear of the headlamp.
3. With the vehicle on a level
surface, usea4mmwrench to
turn the vertical aim adjustment
screw (outboard screw) located on
the back of the lamp assembly
clockwise or counterclockwise until
the bubble in the spirit level is
centered when viewed from
directly above the bubble.
4. Close the hood.
If the vehicle is on a downward or
upward slope of not more than
1.2É, the VHAD's bubble level can
be used to correct for the effects
of the surface slope, provided that
the slope is accurately known.
Maintenance and care
174