hood open FORD ESCORT 1997 7.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: ESCORT, Model: FORD ESCORT 1997 7.GPages: 191, PDF Size: 2.02 MB
Page 128 of 191
3. Block the wheels to prevent the
vehicle from moving unexpectedly.
4. If work must be done with the
engine running, avoid wearing
loose clothing or jewelry that could
get caught in moving parts. Take
appropriate precautions with long
hair.
Opening the hood
1. Inside the vehicle, pull the hood
release handle located under the
bottom left corner of the
instrument panel.
2. Outside the vehicle, release the
auxiliary latch located under the
center of the hood.
3. Lift the hood and secure it in
the open position with the prop
rod.
4. To close the hood, remove the
prop rod and shut so that the
auxiliary latch is closed.
After closing the hood, try to lift it
to be sure that it is closed
securely.
5
HI LOOFF*A/C*MAX
A/C
TUNE
DISCS
SEEK
TUNE
SCAN
EJ REW FF
BAL BASSTREBFADE TAPE
CD AM
FM
–+1
SIDE 1-22
345
COMP1
SIDE 1-2VOL–
PUSH ON
LMIRRORR
0000000002030405060
70
80
90
10 0
11 020 40608010 0
12 0
16 0
18 0 140FUEL FILLCHEF1/22
13RPM x 1000
RESET
SET
ACC
SET XXXX XXXOFF2INT
1 OFF MIST
Maintenance and care
128
Page 131 of 191
To check the engine oil, follow
these steps:
1. Once the engine is warm, turn
the engine off. Make sure the
vehicle is parked on level ground.
2. Automatic transaxle:
²Engage the parking brake.
²Place the gearshift in P.
Manual transaxle:
²Engage the parking brake.
²Depress the clutch and place
the gearshift in first gear.
3. Open the hood. If you need
assistance, refer toOpening the
Hoodin this chapter. Protect
yourself from engine heat.
4. Remove the engine oil dipstick
and wipe it clean. Insert the
dipstick fully, then remove it again.
The oil level should be in the
range shown on the dipstick.
5. Carefully pull the dipstick out
again. If the oil level is below the
ADD arrow, add engine oil as
necessary. If the engine oil is
beyond the FULL arrow, engine
damage or high oil consumption
may occur and some oil must be
removed from the engine.
6. Put the dipstick back and
ensure that it is properly seated.
ADD FULL
Maintenance and care
131
Page 162 of 191
Headlamps
To change the headlamp bulbs:
1. Be sure that the headlamp knob
is in the OFF position.
2. Open the hood and find the
headlamp socket.
3. Remove the protective dust
shield housing by turning the
shield counterclockwise.
4. Remove the bulb retaining ring
by rotating it counterclockwise
(when viewed from the rear).
5. Disconnect the electrical
connector and remove the bulb by
pulling it straight out.
6. Replace the bulb by pushing a
new one straight in with the bulb's
plastic base facing upward. You
may need to turn the bulb slightly
to align the grooves in the plastic
base with the tabs in the bulb
socket.
7. Slip the bulb retaining ring over
the plastic base and lock the ring
by rotating it clockwise until it
snaps.
8. Reconnect electrical connector.
9. Replace the housing protective
dust shield and lock the shield by
rotating clockwise until it locks
into position.
Maintenance and care
162
Page 174 of 191
Adjusting the horizontal aim
1. With the hood open, locate the
horizontal indicator and adjusting
screw.
2.Usea4mmwrench to turn the
horizontal adjusting screw until the
reference mark on the reflector
extension aligns with the ``O''
reference mark on the horizontal
indicator when viewed directly
from above.
3. When the horizontal aim has
been adjusted, close the headlamp
access panel.
Adjusting the vertical aim
1. Do not adjust the vertical aim
until after adjusting the horizontal
aim.
2. With the hood open, locate the
bubble level vertical aim indicator.
It is visible when viewed from
above the rear of the headlamp.
3. With the vehicle on a level
surface, usea4mmwrench to
turn the vertical aim adjustment
screw (outboard screw) located on
the back of the lamp assembly
clockwise or counterclockwise until
the bubble in the spirit level is
centered when viewed from
directly above the bubble.
4. Close the hood.
If the vehicle is on a downward or
upward slope of not more than
1.2É, the VHAD's bubble level can
be used to correct for the effects
of the surface slope, provided that
the slope is accurately known.
Maintenance and care
174