length FORD EXPEDITION 1997 1.G Owners Manual

To shorten the belt:
²Buckle the belt.
²Pull the loose end of the belt
until snug.
To lengthen the belt:
²Tip and pull the tongue.
Do not wear the lap belt around
your waist, keep it low around
your hips.
Front seat safety belt height
adjustment
Adjust the height of the shoulder
belt so that the belt rests across
the middle of your shoulder.
To lower the height of the shoulder
belt:
²Push the button down.
²Slide down.
exd_front_belt_height_adjust
Seating and safety restraints
84

To raise the height of the shoulder
belt:
²Slide up.
²Pull down on the height adjuster
to make sure that it is locked in
place.
Safety belt maintenance
Check the safety belt systems
periodically to make sure that they
work properly and are not
damaged. If your vehicle has been
involved in an accident, have all
the safety belts and child seat
anchoring brackets (if equipped)
examined by a qualified technician.
Refer toCleaning and caring for
your vehiclein theMaintenance
and carechapter for more
information on maintaining your
safety belts.
Failure to replace the
safety belt assembly
under the above conditions
could result in severe
personal injuries in the event
of a collision.
Safety belt extension assembly
For some people, the safety belt
may be too short even when it is
fully extended. You can add about
20 cm (8 in.) to the belt length
with a safety belt extension
assembly (part # 611C22). Safety
exd_extension_assmebly
Seating and safety restraints
85

way back on the seat cushion
when the lower legs hang over the
edge of the seat cushion. You may
wish to discuss the special needs
of your child with your
pediatrician.
INSTALLING CHILD SAFETY
SEATS IN THE REAR SEATING
POSITIONS
To install a child safety seat in a
center rear seating position:
1. Tip the tongue and pull to
lengthen the lap belt.
2. Place the child safety seat in the
center seating position.
3. Route the lap belt through the
child safety seat according to the
manufacturer's instructions.
4. Insert the tongue into the
proper buckle.
5. Push down on the child safety
seat while pulling the loose part of
the belt webbing to tighten the
belt.
6. Before placing the child in the
safety seat, forcibly tilt the seat
from side to side and forward and
back to make sure that the seat is
held securely in place. If the child
seat moves excessively, repeat
steps five and six, install a tether
strap or properly install the child
seat in another seating position.
exd_safety_seats_kids
com_installing_seats.01
Seating and safety restraints
94

treatments used by commercial car
washes can reduce the
effectiveness of wiper blades.
To make reaching the wiper blades
easier, simply:
1. Turn the ignition to the 3(On)
position.
2. Turn the wipers on.
3. Wait for the wipers to reach a
vertical position and turn the
ignition to 2(Lock).
²Do not move the wipers
manually across the windshield,
this may cause damage to both
wipers and windshield.
Replacing front wiper blades
If the wiper blades do not function
properly after cleaning,
replacement of the blade assembly
or the blade element may be
necessary.
The blade lengths for your vehicle
are as follows:
²Front wiper blades Ð
approximately 56 cm (22 in)
²Rear wiper blades Ð
approximately 41 cm (16 in)
3
2
1
5
4
3
2
1
5
4
exd_replacing_wiper_blades
Maintenance and care
180

Dimensions mm(inches)
1 - Overall length 5197 mm (204.6 in)
2 - Overall width 2027 mm (79.8 in)
3 - Maximum height 1963 mm (77.3 in)
4 - Wheelbase 3023 mm (119.0 in)
5 - Front track 1661 mm (65.4 in)
IDENTIFYING YOUR VEHICLE
Vehicle identification tag
The vehicle identification tag is
located on the front panel of the
engine compartment. This tag
bears technical information on
your vehicle and identifies various
components.
55
2
3
exd_plate_identification
exd_vin_number
Capacities and specifications
219