radiator FORD EXPEDITION 1997 1.G Owners Manual

Removing the jack handle
1. Open the hood.
2. Un-snap the end of the handle
that is retained by the clip on the
top of the windshield washer
bottle.
3. Un-snap the shaft of the handle
from the two retaining clips
attached to the top of the radiator
shroud.
Removing the jack and tools
1. Locate the access panel on the
interior trim. Lift and rotate the
two panel retaining clips and
remove panel.
2. Un-snap the wheel lug nut
wrench, instructions and work
gloves from their retaining bracket.
3. Remove the jack by turning the
thumbwheel counterclockwise to
relieve tension against the stowage
bracket.
Removing the spare tire
1. Open the rear liftgate.
2. Insert the straight end of the
jack handle into the rear access
hole located just above the rear
bumper.
²Forward motion will stop and
resistance to turning will be felt
when properly engaged.
3. Turn the handle
counterclockwise until tire is
lowered to the ground and the
cable is slightly slack.
exd_removing_jack_handle
exd_removing_tools
exd_removing_spare
Roadside emergencies
145

Washer fluid in the liftgate
reservoir
Washer fluid for liftgate wiper and
washer operation is supplied by
the washer fluid reservoir located
in the engine compartment. For
information on adding fluid to this
main reservoir, refer toWasher
fluid in the windshield reservoir
in this chapter.
CHECKING AND ADDING
ENGINE COOLANT
Adding engine coolant
Do not put engine coolant
in the container for the
windshield washer fluid.
If sprayed on the windshield,
engine coolant could make it
difficult to see through the
windshield.
When the engine is cool, add a
50/50 mixture of engine coolant
and water to the engine coolant
recovery reservoir Ð DO NOT
ADD DIRECTLY TO THE
RADIATOR. Add straight water
only in an emergency, but you
should replace it with a 50/50
mixture of coolant and distilled
water as soon as possible.
COOLANT FILL
LEVEL
exd_coolant
exd_adding_coolant
Maintenance and care
165

Refill capacities
Capacities - liters (quarts) 4.6 L engine 5.4 L engine
Engine crankcase 5.7 L (6.0
quarts) with filter
change5.7 L (6.0
quarts) with filter
change
Transfer case 1.9L (2.0 quarts)
Automatic transmission 4R70W-13.1L (13.9 quarts)
E4OD (4 x 2) - 15.04L (15.9
quarts)
E4OD (4 x 4) - 15.51L (16.4
quarts)
Washer fluid reservoir 4.1 L ( 4.5 quarts)
4.6 L Engine coolant-2Row
radiator
-1 Row radiator17.9 L (19.9 quarts)
17.0 L (18.0 quarts)
5.4 L Engine coolant 19.7 L (20.8 quarts)
Engine oil 5.7 L (6.0 quarts)
Power steering fluid 2.3 L (2.4 quarts)
Capacites - pints
Axle (rear)
Ford 8.89/ 9.759Ring Gear
Conventional and Traction-Lok
1
5.5 pints
Axle (front) Ford 8.89Ring Gear 3.5 pints
1Add 4 oz. of additive friction
modifier C8AZ-19B546±A, Ford
specification EST-M2C118±A, for
complete fill of 8.8 inch and 9.75
inch ring gear Traction-Lok axles.
Service refill capacities are
determined by filling the rear axle
1/4 inch to 9/16 below the bottom
of the filler hole.
exd_specifications
Capacities and specifications
214