ECO mode FORD EXPLORER 1996 2.G Owner's Manual

256
%*
[DR16101(ALL)03/95]
Four-Wheel Drive (4WD) System
(If equipped)
[DR16130(ALL)10/94]
When you select the 4WD mode, your vehicle uses all four
wheels to power itself. This increases traction, enabling you to
drive your 4x4 over terrain and road conditions not travelled
normally by two-wheel drive vehicles.
*
[DR16160(ALL)10/94]
Power is supplied to all four wheels through a transfer case that
allows you to select four-wheel drive when necessary. Methods
for engaging and disengaging 4WD and low range will depend
on which system your vehicle has.
[DR17585( X)01/95]
4WD Systems Ð Control Trac
[DR17615( X)01/95]
The Control Trac 4WD system functions in three modes. In
two-wheel drive mode, power is delivered only to the rear axle.
The 4WD AUTO position provides four-wheel drive with full
power delivered to the rear axle, and to the front axle as
required for increased traction. The 4WD LOW position
provides four-wheel drive with full power delivered to the front
and rear axles when above average power is required at
reduced speeds.
[DR17645( X)01/95]
Four-wheel drive operation (4WD LOW) on dry pavement is not
recommended. Operating the vehicle in 4WD LOW on dry
pavement will increase noise, vibration, tire wear, and decrease
fuel economy.
[DR17690( X)08/94]
Control Trac system indicator lights
[DR17735( X)03/95]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[DR17750(ALL)01/95]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[DR17790( X)1/96]
n
4WD Auto mode Ð Only the 4WD light is lit.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

258
[DR18230( X)10/94]
Toshiftfrom4WDAUTOor2WDto4WDLOW:
[DR18290( X)01/95]
Stop the vehicle, depress the brake and place the automatic
transmission in N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4WD LOW. Both the 4WD and 4WD LOW
lights are now lit.
[DR18293( X)06/95]
For Explorers equipped with Automatic Ride Control:
[DR18294( X)06/95]
After shifting to 4WD LOW, wait about 90 seconds. This will
improve ground clearance and off-road handling. Refer to
Automatic Ride Controlin the Features chapter.
[DR18320( X)08/94]
To shift from 4WD LOW to 4WD AUTO or 2WD:
[DR18400( X)01/95]
Stop the vehicle, depress the brake and place the automatic
transmission into N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4WD AUTO or 2WD.
[DR18500(ALL)03/95]
It is not recommended to operate the vehicle in the 4WD modes
with a temporary spare. If 4WD operation is necessary, do not
operate at speeds above 10 mph or for distances above 50 miles.
Extended operation in 4WD with a temporary spare may result
in damage to drivetrain components.
[DR18600( X)12/95]
All-Wheel Drive System (If equipped)
[DR18620( X)12/95]
If your vehicle is equipped with All-Wheel Drive (AWD), power
is constantly supplied to all four wheels through a transfer case.
The AWD system is full-time and has no external controls.
[DR18630( X)12/95]
The AWD transfer case utilizes a viscous clutch that distributes
torque to the front and rear differentials (approximately 35%
front and 65% rear). The viscous clutch is filled with a
high-viscosity fluid, see
Lubricant Specifications
in the
Servicing
Your Explorer
chapter for more information.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

264
[DR22965(ALL)05/95]
Should a malfunction in the 4WABS system occur, the ABS light
on the instrument cluster will come on and stay on indicating
that the anti-lock system has been shut down and the vehicle
needs to be serviced. Normal braking is not affected unless the
brake warning light is also illuminated.
*
[DR22970(ALL)09/95]
NOTE: It is important to note that when the ABS Warning
Light is illuminated the ABS system is disabled. The
vehicle must be serviced immediately to restore the
benefits of the Anti-lock system.
*
[DR22975(ALL)09/95]
NOTE: Mobile phones or radio transmitters not installed by
Ford Motor Company may interfere with the Anti-lock
System. Should the Anti-lock system activate
unexpectedly or the Anti-lock Warning Light
illuminate after installation of such a unit, have the
installation of the unit checked.
%*
[DR23000(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is ªLowº
*
[DR23250(ALL)11/89]
If during normal operation the brake pedal seems ªlowº, it may
indicate the need for a brake system inspection and/or service.
You should have your brakes checked as soon as possible.
*
[DR23300(X)07/95]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified service technician.
*
[DR23400(ALL)11/89]
RWARNING
Modifications to the suspension spring rates and/or
vehicle ride height may adversely affect vehicle stopping
ability.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
265
*
[DR23500(ALL)07/92]
If Brakes Pull
*
[DR23600(ALL)05/95]
n
Check tire pressure.
[DR23710( X)07/95]
n
If pull occurs during the first 500 miles (800 km), make 10
moderatley fast stops from 40 mph (64 km/h). It may be
necessary to repeat this operation to properly seat new
brakes.
*
[DR23800(ALL)05/95]
If pull occurs during the first 500 miles (800 km), make 10
moderately fast stops from 40 mph (65 km/h) and then
perform the self-adjustment procedure above. It may be
necessary to repeat this operation to properly seat new brake
linings and pads.
%*
[DR24000(ALL)01/93]
Stopping Distances
*
[DR24100(ALL)11/89]
Stopping distances vary with different loads and driving
conditions. Use caution when encountering new conditions and
acquaint yourself with vehicle performance. Take full advantage
of engine braking power when slowing down.
%*
[DR24200(ALL)01/95]
Applying the Brakes
*
[DR24300(ALL)05/95]
Apply the brake pedal gradually. Use the ªsqueezeº technique
Ð push on the brake pedal with a steadily increasing force. This
allows the wheels to continue to roll while you are slowing
down, which lets you steer properly.
*
[DR24400(ALL)07/95]
Do not drive with your foot resting on the brake pedal. This
will increase your vehicle's stopping distance and may also
cause brake damage.
*
[DR24500(ALL)05/95]
RWARNING
If you are driving down a long or steep hill, shift to a
lower gear. Do not apply your brakes continuously, as
they may overheat and become less effective.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

268
*
[DR25350(ALL)03/95]
Operate your vehicle within reasonable limits. Sudden
acceleration, deceleration, turning, or combinations of these
maneuvers can cause a vehicle to behave differently than
anticipated.
*
[DR25501(ALL)02/95]
Wheel Spin
*
[DR25550(ALL)11/92]
n
Extreme acceleration can cause the rear wheels to spin,
perhaps resulting in reduced steering control.
[DR26350(ALL)12/92]
If the wheels spin, use 2 (Second gear) to gain traction. Move
forward slowly and evenly. If this does not work, try rocking
the vehicle.
*
[DR26401(ALL)05/91]
For 4x4 vehicles, engage 4WD, and try to drive away.
%*
[DR26550(ALL)05/90]
High Speed Driving
*
[DR26590(ALL)07/95]
Ford Motor Company recommends obeying posted speed limits.
*
[DR26601(ALL)05/95]
RWARNING
Driving too fast for conditions creates the possibility of
loss of vehicle control. Driving at very high speeds for
extended periods of time may result in damage to vehicle
components.
*
[DR26625(ALL)12/91]
Speed limiter
[DR26652(ALL)01/95]
All models are equipped with a Powertrain Control Module
(PCM) which limits the maximum engine speed and thus road
speed in top gear. Vehicle operation is normal since the
controlled maximum speed is above posted highway speeds in
North America.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
275
*
[DR30310(ALL)06/92]
n
GCWR (Gross Combined Weight Rating)
*
[DR30320(ALL)06/92]
n
Maximum Trailer Weight Rating
*
[DR30330(ALL)06/92]
n
Maximum Trailer Weight
*
[DR30340(ALL)06/92]
n
Trailer Weight Range
*
[DR30351(ALL)03/91]
Base Curb Weight
*
[DR30401(ALL)03/94]
The Base Curb Weight is the weight of the vehicle including
fuel, coolants, lubricants, emergency tools, spare wheel and tire.
It also includes any equipment that isstandardon that model. It
does not include passengers, cargo or optional equipment
installed by factory, dealer, aftermarket supplier or customer.
*
[DR30451(ALL)03/91]
Payload
*
[DR30501(ALL)03/91]
Payload is the combined, maximum allowable weight of cargo,
occupants and optional equipment that the truck is designed to
carry. It is Gross Vehicle Weight Rating minus the base curb
weight.
*
[DR30550(ALL)03/91]
Gross Vehicle Weight (GVW)
*
[DR30601(ALL)05/95]
If you add base curb weight and the weight of a load (including
passengers, cargo and optional equipment) being carried at a
particular time, you get the Gross Vehicle Weight (GVW).
*
[DR30650(ALL)08/95]
It is important to remember that GVWis not a limit or a
specification.If an owner loads up a vehicle and weighs it, that's
the GVW at that moment. If the owner piles on more of a load
and weighs it again, that becomes the GVW.
%*
[DR30701(ALL)03/91]
Gross Vehicle Weight Rating (GVWR)
*
[DR30750(ALL)10/94]
To avoid overloading a vehicle, the owner should observe the
manufacturer's specified Gross Vehicle Weight Rating. The
GVWR is the maximum total weight of base vehicle, passengers,
optional components and cargo that a particular vehicle was
designed to carry.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

300
[RE04150(ALL)12/95]
It is not recommended that vehicles equipped with 4WD be
operated in the 4WD modes with a temporary spare. If 4WD
operation is necessary, do not operate at speeds above 10 mph
(16 km/h) or for distances above 50 miles (80 km). Extended
operation in 4WD with a temporary spare may result in damage
to powertrain components.
*
[RE04200(ALL)01/93]
RWARNING
If you use the temporary spare tire continuously or do
not follow these precautions, the tire could fail, causing
you to lose control of the vehicle, possibly injuring
yourself or others.
*
[RE04275(ALL)05/95]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
*
[RE04280(ALL)10/94]
Extended use of other than matching size spare tires on a
Traction-Lok axle could result in a permanent reduction in
effectiveness. This loss of effectiveness does not affect normal
driving and should not be noticeable to the driver.
*
[RE04300(ALL)01/95]
When you drive with the temporary spare tire, DO NOT:
*
[RE04400(ALL)01/95]
n
exceed 50 mph (80 km/h) under any circumstances.
*
[RE04500(ALL)01/95]
n
load your vehicle so that it is heavier than the maximum
vehicle load rating listed on the tire decal.
*
[RE04600(ALL)01/95]
n
tow a trailer.
*
[RE04700(ALL)01/95]
n
use tire chains on this tire.
*
[RE04800(ALL)01/95]
n
try to repair the temporary spare tire or remove it from its
wheel.
*
[RE04900(ALL)01/95]
n
use the wheel for any other type of vehicle.
[RE04950(ALL)10/94]
n
engage four-wheel drive on dry, hard-surfaced roads.
File:12unrex.ex
Update:Thu Feb 29 09:14:34 1996

Servicing Your Explorer
401
*
[SV49800(ALL)02/92]
Never use a metal exhaust collector when you service your
vehicle. If the metal collector contacts any of your vehicle's
plastic trim or bumper parts they could melt or deform.
*
[SV49900(ALL)01/95]
Do not drive your vehicle if it does not operate properly. See
your dealer if the engine runs on for more than five seconds
after you shut it off or if it misfires, surges, stalls, or backfires.
%*
[SV50000(ALL)05/95]
Information about your vehicle's emission control system is on
the Vehicle Emission Control Information decal located on or
near the engine. This decal identifies engine displacement and
gives some tune-up specifications.
%*
[SV51475(ALL)07/95]
Readiness for Inspection/Maintenance Testing
*
[SV51480(ALL)07/95]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If the vehicle's powertrain system or its battery
has just been serviced, the OBD II system is reset to a not ready
for I/M testing condition. To prepare for I/M testing, the law
specifies a ªneed for additional mixed city and highway driving
to complete the checkº of the OBD II system. As soon as all of
the OBD II system checks are successfully completed, the OBD
II system is set to the ready condition. The amount of driving
required to reach the ready condition varies with individual
driving patterns. To complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle defined below.
If the vehicle owner cannot or does not want to do the
additional driving required by law, a service center can perform
this drive cycle as it would any other type of repair work.
*
[SV51485(ALL)09/95]
OBD II Drive Cycle
*
[SV51490(ALL)06/95]
The following steps must be run in the order shown. If any
steps are interrupted, repeat the preceding step. Any safe
driving mode is acceptable between steps.
*
[SV51495(ALL)06/95]
Always drive vehicle in safe manner according to traffic
conditions and obey all traffic laws.
File:15unsvx.ex
Update:Thu Feb 29 09:20:34 1996

402
*
[SV51500(ALL)07/95]
The engine must be warmed up and at operating temperature
before proceeding with the drive modes of the following OBD II
Drive Cycle.
*
[SV51505(ALL)06/95]1.
Start the engine. Drive or idle (in neutral) the vehicle for 4
minutes.
[SV51510(ALL)05/95]2.
Idle the vehicle in drive (neutral for automatic transmissions)
for 40 seconds.
[SV51515(ALL)05/95]3.
Accelerate the vehicle to 45 mph (72 km/h) (for manual
transmissions upshift from 1st to 5th gear, but hold in 2nd
for at least 5 seconds) at 1/4 to 1/2 throttle for 10 seconds.
*
[SV51520(ALL)05/95]4.
Drive the vehicle with a steady throttle at 45 mph
(72 km/h) (manual transmissions use 5th gear) for 30
seconds.
*
[SV51525(ALL)08/95]5.
Idle the vehicle in drive (neutral for manual transmissions)
for 40 seconds.
*
[SV51530(ALL)05/95]6.
Continue to drive the vehicle in city traffic at speeds
between 25 and 40 mph (40-64 km/h) (manual transmissions
primarily drive vehicles in 3rd and 4th gear when possible)
for 15 minutes. During the 15 minute drive cycle the
following modes must be achieved:
[SV51535(ALL)05/95]
a. at least 5 stop and idle modes at 10 seconds each.
[SV51540(ALL)05/95]
b. acceleration from idles at 1/4 to 1/2 throttle position, and
[SV51545(ALL)05/95]
c. choose three different speeds to do 1.5 minute steady state
throttle drives.
File:15unsvx.ex
Update:Thu Feb 29 09:20:34 1996