lights FORD EXPLORER 1996 2.G Owner's Manual

110
[IP00400( X)03/95]
The main controls for the climate control system, lights, message
center, lamps, clocks and radio are on the instrument panel.
%*
[IP00475(ALL)09/95]
NOTE: Any cleaner or polish that increases the gloss (shine)
of the upper part of the instrument panel should be
avoided. The dull finish in this area is to help protect
the driver from undesirable windshield reflection.
%*
[IP00500(ALL)06/95]
The Climate Control Systems
*
[IP00601(ALL)12/91]
Your vehicle is equipped with a control assembly designed to
handle either a combination A/C-Heater System or a
Heater-Only System.
%*
[IP00801(ALL)10/93]
Instrument Panel Registers
*
[IP00901(ALL)02/95]
There are four registers in the instrument panel. Each of these
registers contains a louver assembly which can be manually
adjusted to direct airflow up, down, left and right. An
illustration of the register locations follows.
[IP01201(ALL)04/94]
7-1/2 pica art:0020099-D
Instrument panel registers
[IP01400(ALL)12/91]
Air Conditioning (A/C) Controls (Manual Air
Conditioning)
*
[IP01450(ALL)02/95]
The control for your air conditioning and heater system is
located at the center of the instrument panel below the radio
and will operate only when the ignition key is turned to the
ON position. Your air conditioner and heater will heat and/or
cool your vehicle interior depending on the function position
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

Instrument Panel Controls
127
[IP15800( X)10/94]
Liftgate Wiper and Washer (If equipped)
[IP15901( X)10/94]
The wiper/washer switch is to the right of the radio. To turn on
the wiper, rotate the wiper/washer switch to the WIPE position.
To select an interval wipe rotate switch between OFF and HI.
To turn on the washer, push the switch all the way in and hold
for spray. Release the button and the spray stops, but the wiper
continues to operate. To turn off the wiper, rotate the switch to
the OFF position.
[IP15950( X)12/92]
For information about refilling the liftgate washer fluid or
replacing your liftgate wiper blade, seeWindshield washer fluid
andWindshield wipersin the Index.
[IP16000( X)05/95]
7-1/2 pica art:0090189-A
Liftgate wiper/washer button
%*
[IP16800(ALL)01/95]
The Interior and Exterior Lights
%*
[IP16900(ALL)01/95]
Turning On the Exterior Lights
*
[IP17000(ALL)09/95]
To turn on your headlamps, parking lamps, marker lamps,
license plate lamps and tail lamps, use the headlamp control
knob to the left of the steering column.
[IP17100(ALL)09/95]1.
Rotate the headlamp control knob to the first position.
Parking lamps, tail lamps, license plate lamps and marker
lamps are now on.
[IP17200(ALL)06/94]2.
Rotate the headlamp control knob to the next position.
Headlamps are now on in addition to the above.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

132
%*
[IP17780(ALL)08/95]
Cleaning the Exterior Lamps
*
[IP17785(ALL)08/95]
Do not use dry paper towel, chemical solvents or abrasive
cleaners to clean the lamps, as these may cause scratches or
crack the lamps.
%*
[IP17815(ALL)01/95]
Daytime Running Light System
*
[IP17820(ALL)03/95]
(Canadian vehicles only)
*
[IP17830(ALL)03/95]
The Daytime Running Light (DRL) system turns the high beam
headlamps on, with a reduced light output, when:
*
[IP17840(ALL)03/95]
n
The headlamp system is in the OFF position, and
*
[IP17850(ALL)01/95]
n
The vehicle has a fully released parking brake.
*
[IP17860(ALL)05/95]
The high beam indicator light on the instrument cluster will not
be on.
*
[IP17890(ALL)05/95]
RWARNING
The Daytime Running Light (DRL) system will not
illuminate the tail lamps and parking lamps. Turn on
your headlamps at dusk. Failure to do so may result in a
collision.
%*
[IP17900(ALL)03/95]
Lighting Up the Instrument Panel and the Interior of
Your Vehicle
[IP18000(ALL)10/94]
The instrument panel lights can be turned on by turning the
headlamp knob toward either the first or second position. You
can brighten or dim the instrument panel lights by rotating the
thumb wheel.
[IP18200(ALL)03/95]
The interior lights will shut off after 25 seconds with all the
doors closed, or immediately when the ignition switch is turned
to the ON position, or if the vehicle speed is above five MPH
(8 km/h). The interior lights will turn off after 40 minutes if
any of the doors are left open. Refer toBattery Saverin the
Featuressection for more details.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

138
[SC05502(ALL)10/94]
Gearshift Lever (Automatic transmission
only)
[SC05504( X)08/94]
The gearshift lever on your Explorer is mounted on the steering
column. On the end of the gearshift lever is the Overdrive
On/Off button. For additional information about the gearshift
lever and the Overdrive On/Off button, see theDriving Your
Explorerchapter.
[SC05508(ALL)10/94]
7-1/2 pica art:0021255-A*
[SC05510(ALL)11/93]
OVERDRIVE OFF Lamp
[SC05512(ALL)03/95]
This lamp indicates the operating range of the transmission.
This lamp illuminates when the O/D ON/OFF button is
depressed. For additional information, refer to theWarning
Lights and Gaugeschapter.
[SC05514(ALL)07/95]
6 pica art:0021226-BFile:07unscx.ex
Update:Thu Feb 29 09:06:35 1996

156
%*
[FV15203( X)09/95]
Using the Keyless Entry System (If equipped)
*
[FV15205( X)02/95]
If your vehicle has the keyless entry system, you can lock or
unlock the vehicle doors without using a key. The buttons for
the system are near the outside door handle on the driver's
side. See alsoRemote Entry Systemwhich follows this
description.
[FV15207( X)02/95]
10-1/2 pica
art:0021158-A
Keyless entry buttons
*
[FV15209( X)02/95]
When you bought your vehicle, you were given a computer
code that operates the system for your vehicle. For your
convenience, we have duplicated this code in two places.
*
[FV15211( X)09/95]
The code is:
*
[FV15213( X)09/95]
n
on your owner's wallet card found in the glove compartment
*
[FV15217( X)02/95]
n
taped to the computer module
*
[FV15219( X)05/95]
When you use this entry system, the illuminated entry system
turns on the interior lights for 25 seconds and the buttons on
the keypad light up for 5 seconds. Do not push the buttons
with a key, ballpoint pen, pencil or any other hard object. These
objects could damage the buttons.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

162and the liftgate window are completely closed, the doors and
liftgate will lock again, the horn will chirp and the external
lamps will flash. If a door, liftgate or the liftgate window is
open or ajar, the horn will give two short chirps warning you
that a door or the liftgate is open.
%*
[FV16800(ALL)02/95]
Remote entry personal alarm
*
[FV16900(ALL)02/95]
If you wish to activate the remote entry system personal alarm,
press the PANIC button. This will honk the horn and flash the
lights for approximately 2 minutes 45 seconds. You can turn it
off by pressing the PANIC button again from the transmitter or
by turning the ignition to the ON or ACCESSORY position.
*
[FV17000(ALL)02/95]
When you use the remote entry UNLOCK or PANIC buttons,
the illuminated entry system turns on the vehicle's interior
lights for 25 seconds. You can turn these lights off with the
remote entry LOCK button or by turning the ignition to the ON
or ACCESSORY position.
[FV17100(ALL)03/95]
7-1/2 pica art:0021160-A%*
[FV17200(ALL)04/95]
Arming and Disarming the Alarm System with Remote
Entry
*
[FV17350(ALL)04/95]
Your Remote Entry System will automatically arm the factory
installed Anti-Theft System when the doors are locked, and
automatically disarm it when the doors are unlocked. The
remote will also reset the anti-theft alarm (when the driver's
door is unlocked or the PANIC button is pressed on a
programmed remote entry transmitter) if it was triggered.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

166
%*
[FV18101(ALL)02/95]
Replacing lost transmitters
[FV18200(ALL)07/95]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[FV18301(ALL)02/95]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[FV18601(ALL)04/95]
Illuminated Entry System (If equipped)
*
[FV18701(ALL)06/95]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
*
[FV18801(ALL)09/95]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
[FV18810( X)10/94]
Delayed Accessory
[FV18815( X)08/94]
This feature provides power to operate the power windows and
power moon roof for 10 minutes after the ignition switch is
turned from the RUN to the OFF position.
[FV18820( X)06/94]
If either front door is opened during the 10 minute period the
delayed accessory feature will be disabled.
%*
[FV18900(ALL)08/94]
Battery Saver
*
[FV19000(ALL)03/95]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

Features
167
[FV19100( X)03/95]
This will prevent draining of the battery if these lights have
been left on inadvertently or if a door or the liftgate is not
completely closed. Battery voltage to these lamps will be
restored when the remote entry transmitter is used, any door is
opened, the liftgate is opened, or the ignition key is turned ON
again.
%*
[FV19104(ALL)09/95]
Anti-Theft Alarm System (If equipped)
*
[FV19106(ALL)05/95]
When armed, this system helps protect your vehicle against
break-ins or theft.
%*
[FV19109(ALL)05/95]
When an unauthorized entry occurs, the system triggers and
will:
*
[FV19112( X)02/95]
n
flash the headlamps, parking lamps, and theft indicator lamp
*
[FV19115(ALL)06/95]
n
honk the horn
*
[FV19118(ALL)05/95]
n
disable the starting circuit to prevent the vehicle from being
started
% [FV19121(ALL)02/95]
Arming the System
*
[FV19124(ALL)04/95]
The system is ready to arm any time the ignition switch is
turned OFF and the alarm is not triggered or sounding. Any of
the following events will prearm the anti-theft system:
[FV19130(ALL)04/95]
n
Pressing the remote entry transmitter LOCK button to lock
the doors (with the doors open or closed),
[FV19133( X)04/95]
n
Pressing the 7/8 and 9/0 buttons on the keyless entry
keypad at the same time to lock the doors (with the doors
open or closed), or
*
[FV19136(ALL)04/95]
n
Opening a door and pressing the power door lock button to
lock the doors.
*
[FV19140( X)04/95]
If a door, liftgate or liftgate window is open, the anti-theft
system is prearmed and waiting for all doors to close. The
THEFT indicator in the instrument panel will light continuously
while the system is prearmed.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

Features
169
*
[FV19200(ALL)02/95]
When unlocking the vehicle with a key, turn the key all the
way to the end of its travel or the system may not disarm.
*
[FV19202(ALL)09/95]
NOTE: The flashing lights and honking horn will shut off
automatically within 2 minutes 45 seconds after the
system is triggered. It will trigger again if another
intrusion occurs. However, the starter circuit remains
disabled until the system is disarmed.
*
[FV19205(ALL)05/95]
The anti-theft system is designed to work with the factory
installed remote entry system. It may not work with other
remote entry systems.
[FV19210( X)06/94]
Automatic Ride Control System
(If equipped)
[FV19213( X)03/95]
The automatic ride control system is designed to improve ride,
handling, and general vehicle performance for both on and
off-road conditions by adjusting vehicle ride height and shock
dampening (firm or soft).
[FV19216( X)08/94]
The system automatically controls the vehicle ride height over a
range of approximately two inches based on vehicle speed and
selection of two or four wheel drive modes. Also, the system
keeps the vehicle at a constant level if a load is added to or
removed from the vehicle.
[FV19218( X)03/95]
The automatic ride control system places the vehicle at its
lowest height when two wheel drive is selected. Shock
dampening is automatically set based on driver and road inputs
to optimize ride.
[FV19220( X)03/95]
The automatic ride control system raises the vehicle
approximately one inch when Auto 4WD is selected. However,
if vehicle speed exceeds 58 mph (93 km/h), the system will
lower the vehicle to its two wheel drive height to maximize ride
comfort. The vehicle will raise again if vehicle speed is less than
30 mph (48 km/h) for one minute. Like the two wheel drive
mode, shock dampening is automatically set based on driver
and road inputs.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

170
[FV19224( X)03/95]
In 4WD Low, the automatic ride control system raises the
vehicle approximately two inches above its lowest height. Shock
dampening is locked in firm mode. The height change improves
body clearance. The combination of firm dampening and the
height change also provides maximum suspension feedback for
improved off-road safety and performance.
[FV19226( X)03/95]
The vehicle will drop to its lowest position when the ignition is
turned OFF to provide ease of entry and exit of the vehicle.
[FV19229( X)03/95]
As a safety consideration, whenever a door is opened, including
the liftgate and liftgate glass, the system memorizes and
maintains the height at the moment the door was opened. The
system will maintain this height until either the doors are all
closed or vehicle speed exceeds 10 mph (16 km/h).
[FV19234( X)03/95]
An on-board air compressor and solenoids are used to raise and
lower the vehicle. It is normal to occasionally hear a buzz or
clicking from the vehicle even when the ignition is turned off.
The system stays energized for forty minutes after ignition is
turned off to compensate for any load changes made after the
vehicle is parked.
[FV19237( X)05/95]
The automatic ride control system operation can be monitored
through the message center. Refer toMessage Centerin the
Warning Lights and Gaugeschapter for more details.
[FV19240( X)08/94]
Service Switch
[FV19243( X)08/94]
The automatic ride control service switch is mounted in the jack
storage area. The switch should be turned off to disable the
automatic ride control system during jacking, hoisting, towing,
or transport of the vehicle to avoid unexpected vehicle
movement.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996