service FORD EXPLORER 1996 2.G Owner's Manual

Warning Lights and Gauges
105
[LG39200( X)04/94]
Check Brake Lamps
[LG39250( X)03/95]
This warning message is displayed when you turn on your
brakelamps by pressing the brake pedal and at least one of the
lamps is burned out.
[LG39300( X)04/94]
If you use additional lights, such as trailer lights, or if you
replace the headlamps or bulbs with equipment that is not equal
to the original equipment from Ford, you may get a false
ªCHECK LAMPSº warning or no warning at all.
[LG39350( X)06/94]
Air Ride Switch Off (If equipped)
[LG39400( X)03/95]
This warning message is displayed when the air suspension
switch, located in the rear jack stowage area on the left side, is
off. For information about the operation of the air suspension
switch, seeAutomatic ride control systemin the Index.
[LG39450( X)06/94]
Check Air Ride System (If equipped)
[LG39500( X)03/95]
This warning message is displayed when an air suspension
system fault has been detected. If this warning message is
displayed while driving, safely pull off the road at your earliest
convenience. If the vehicle is loaded beyond the recommended
maximum payload, the CHECK AIR RIDE SYSTEM message
may be displayed. This is a normal condition if the vehicle is
overloaded. To correct this condition, remove or redistribute the
payload per the recommended maximum requirements. Turn the
ignition switch from ON to OFF and ON again. If the warning
message reappears, turn the air suspension switch (located in
the rear jack stowage area on the left side) OFF and take your
vehicle to a dealership for service as soon as possible.
*
[LG39550( X)01/95]
Change Oil Soon or Oil Change Required
*
[LG39600( X)01/95]
One of these warning messages is displayed when the engine oil
life remaining is 5% or less. When Oil Life Left is between 5%
and 0%, the ªCHANGE OIL SOONº message will be displayed.
When Oil Life Left reaches 0%, the ªOIL CHANGE REQUIREDº
message will be displayed.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

124
*
[IP09000( X)04/95]
n
To prevent humidity buildup inside your vehicle, always
drive with the EATC System turned on.
*
[IP09100( X)03/95]
n
Do not put objects under the front seats that interfere with
the flow of air to the back seat area.
[IP09200( X)03/95]
n
Remove any snow, ice, or leaves from the air intake area of
your EATC System which could block the air intake. The
intake area is located at the bottom of the windshield.
*
[IP09300( X)04/95]
Service
*
[IP09400( X)04/95]
If your EATC is not operating as described here, take it to your
dealer to have it checked. System diagnostics are built in which
will allow your dealer to readily identify problems that might
occur.
[IP09500( X)10/94]
Rear Fan and Airflow Operation
*
[IP09600( X)03/95]
Fan speed adjustment
[IP09700( X)05/95]
The
H(right) knob controls the volume of air flow. Rotate the
knob upward to increase fan speed and increase the amount of
air entering the vehicle. Three fan speed positions are available
and are indicated by dots beside the
Hknob. The largest dot is
high speed position.
[IP09800( X)10/94]
InO (OFF), all blower motor operation is stopped.
*
[IP09900( X)08/94]
Airflow selections
[IP10000( X)05/95]
Q(Vent)
[IP10100( X)05/95]
Airflow will be to the upper console registers whenQis
selected.
*
[IP10200( X)08/95]
R(Floor)
[IP10300( X)05/95]
Airflow will be to the floor whenRis selected.
File:06unipx.ex
Update:Thu Feb 29 09:05:45 1996

170
[FV19224( X)03/95]
In 4WD Low, the automatic ride control system raises the
vehicle approximately two inches above its lowest height. Shock
dampening is locked in firm mode. The height change improves
body clearance. The combination of firm dampening and the
height change also provides maximum suspension feedback for
improved off-road safety and performance.
[FV19226( X)03/95]
The vehicle will drop to its lowest position when the ignition is
turned OFF to provide ease of entry and exit of the vehicle.
[FV19229( X)03/95]
As a safety consideration, whenever a door is opened, including
the liftgate and liftgate glass, the system memorizes and
maintains the height at the moment the door was opened. The
system will maintain this height until either the doors are all
closed or vehicle speed exceeds 10 mph (16 km/h).
[FV19234( X)03/95]
An on-board air compressor and solenoids are used to raise and
lower the vehicle. It is normal to occasionally hear a buzz or
clicking from the vehicle even when the ignition is turned off.
The system stays energized for forty minutes after ignition is
turned off to compensate for any load changes made after the
vehicle is parked.
[FV19237( X)05/95]
The automatic ride control system operation can be monitored
through the message center. Refer toMessage Centerin the
Warning Lights and Gaugeschapter for more details.
[FV19240( X)08/94]
Service Switch
[FV19243( X)08/94]
The automatic ride control service switch is mounted in the jack
storage area. The switch should be turned off to disable the
automatic ride control system during jacking, hoisting, towing,
or transport of the vehicle to avoid unexpected vehicle
movement.
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

Features
171
[FV19246( X)03/95]
17-1/2 pica
art:0021253-A
Automatic Ride Control service switch
%*
[FV19250(ALL)02/95]
Windows
*
[FV19300(ALL)08/95]
Operating the Windows Manually
*
[FV19400(ALL)08/95]
The door windows are opened and closed by turning the handle
crank.
[FV19600(ALL)04/94]
7-1/2 pica art:0021163-A
Manual window operation
File:08unfvx.ex
Update:Thu Feb 29 13:56:40 1996

216
*
[AS06800( X)01/95]
How to store the tape
*
[AS06900( X)01/95]
Press the“AM/FM”button to stop the tape player and resume
radio play.
*
[AS07000( X)08/95]
Using the Dolby
B noise reduction feature
*
[AS07100( X)09/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation.“Dolby”and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
[AS07200( X)07/95]
Push thekbutton to activate. When activated, the light
above thekbutton illuminates.
*
[AS07300( X)08/95]
Tape error messages
*
[AS07400( X)08/95]
Your cassette tape player is equipped to diagnose certain
problems you may experience. Error codes are as follows:
*
[AS07500( X)01/95]
TD E1—Radio tries to change sides of tape 3 times in a 10
second span. Push“EJECT”and try another tape. If problem
persists, refer problem to qualified personnel for service.
*
[AS07600( X)01/95]
TD E2—Tape eject failure. Radio tries to eject tape and it will
not eject. Push“EJECT”to eject tape. If the tape will not eject,
refer problem to qualified personnel for service.
*
[AS07700( X)01/95]
TD E3—Loading error. Push“EJECT”to eject tape. Reload
tape. If the same error code appears in the display, try another
tape.
[AS07705( X)09/94]
Rear Seat Radio Controls (If equipped)
[AS07710( X)09/94]
Rear seat radio controls are available on vehicles equipped with
Premium and Luxury Audio Systems only.
[AS07715( X)09/94]
The rear seat radio controls are located on the rear of the center
console. These controls duplicate several radio functions of the
radio and allow the use of headphones in the vehicle.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
243
*
[AS36500(ALL)08/95]
Automatic gain control circuitry for both AM and FM bands has
been incorporated into this system to reduce strong signal
capture and overload.
%*
[AS36600(ALL)08/95]
All About Radio Frequencies
*
[AS36700(ALL)08/95]
The Federal Communications Commission (FCC) and the
Canadian Radio Telecommunications Commission (CRTC)
establish the frequencies that AM and FM radio stations may
use for their broadcasts. The allowable frequencies are, AM: 530,
540...1600, 1610 kHz in 10 kHz steps; FM: 87.9, 88.1...107.7, 107.9
MHz in 0.2 MHz steps.
*
[AS36800(ALL)08/95]
Not all frequencies will be assigned to a given area. This radio
will tune to each of these frequencies using manual tune and no
fine tuning is necessary as radio stations may not use other
frequencies.
*
[AS36900(ALL)08/95]
Some FM radio stations advertise a”rounded-off“frequency
which is not the frequency they actually broadcast on. For
example, a radio station that is assigned a frequency of 98.7
MHz may call itself”Radio 99“even though 99.0 MHz is not an
allowable FM broadcast frequency.
%*
[AS37000(ALL)08/95]
Important Warranty and Service Information
*
[AS37050(ALL)08/95]
Warranty
*
[AS37100(ALL)08/95]
Your sound system is warranted for three years or 36,000 miles
(60,000 kilometers), whichever comes first. Consult your vehicle
warranty booklet for further information. Ask your dealer for a
copy of this limited warranty.
*
[AS37300(ALL)08/95]
Service
*
[AS37400(ALL)08/95]
At Ford Electronics, we stand behind our audio systems with a
comprehensive service and repair program. If anything should
go wrong with your Ford audio system, return to your dealer
for service. There is a nationwide network of qualified Ford
authorized repair centers to assist you.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

254
*
[DR15100(ALL)03/95]
When you slow down or climb a steep hill, always downshift
before the engine starts to lose power. Downshifting reduces the
chance of stalling and gives your vehicle better acceleration to
increase speed again.
*
[DR15200(ALL)03/95]
When you drive down steep hills, downshifting helps you keep
a safe speed and helps prevent unnecessary wear on the brakes.
*
[DR15300(ALL)03/95]
When you come to a stop, do not downshift through each gear.
Disengage the clutch and use the brake as necessary.
Downshifting through the gears decreases your vehicle's fuel
economy.
*
[DR15400(ALL)05/95]
RWARNING
Continued use of a damaged or worn clutch, prolonged
clutch slippage or downshifting at excessive speeds can
result in a failure of the engine, transmission or clutch
components.
*
[DR15500(ALL)03/91]
Transmission Function
[DR15600(ALL)10/94]
Upshift at the speeds specified in the chart. All forward gears
are synchronized allowing you to shift into them with your
vehicle in motion. The clutch pedal should be fully depressed
when shifting.
*
[DR15625(ALL)04/94]
NOTE: Shifting during extremely low rpm's can result in a
momentary audible rattle which disappears as vehicle
rpm's are increased. Shifting at higher speeds will
eliminate this sound.
*
[DR15700(ALL)03/95]
Parking
*
[DR15800(ALL)01/95]
To park your vehicle, apply the service brake pedal, and shift
into N (Neutral) while still maintaining pressure on the service
brake. Set the parking brake fully. Shift into first and turn off
the ignition.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

256
%*
[DR16101(ALL)03/95]
Four-Wheel Drive (4WD) System
(If equipped)
[DR16130(ALL)10/94]
When you select the 4WD mode, your vehicle uses all four
wheels to power itself. This increases traction, enabling you to
drive your 4x4 over terrain and road conditions not travelled
normally by two-wheel drive vehicles.
*
[DR16160(ALL)10/94]
Power is supplied to all four wheels through a transfer case that
allows you to select four-wheel drive when necessary. Methods
for engaging and disengaging 4WD and low range will depend
on which system your vehicle has.
[DR17585( X)01/95]
4WD Systems Ð Control Trac
[DR17615( X)01/95]
The Control Trac 4WD system functions in three modes. In
two-wheel drive mode, power is delivered only to the rear axle.
The 4WD AUTO position provides four-wheel drive with full
power delivered to the rear axle, and to the front axle as
required for increased traction. The 4WD LOW position
provides four-wheel drive with full power delivered to the front
and rear axles when above average power is required at
reduced speeds.
[DR17645( X)01/95]
Four-wheel drive operation (4WD LOW) on dry pavement is not
recommended. Operating the vehicle in 4WD LOW on dry
pavement will increase noise, vibration, tire wear, and decrease
fuel economy.
[DR17690( X)08/94]
Control Trac system indicator lights
[DR17735( X)03/95]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[DR17750(ALL)01/95]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[DR17790( X)1/96]
n
4WD Auto mode Ð Only the 4WD light is lit.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

Driving Your Explorer
261
*
[DR20900(ALL)11/89]
When climbing a steep hill, start in a lower gear, rather than
finding it necessary to downshift from a higher gear after the
ascent has started. This reduces strain on the engine and the
possibility of stalling.
*
[DR21000(ALL)11/89]
When descending a steep hill avoid sudden braking. Rapid
pumping of the brake pedal will help slow the vehicle and still
maintain steering control.
*
[DR21101(ALL)11/89]
Driving on Snow or Ice
*
[DR21200(ALL)12/95]
A four-wheel drive or all-wheel drive vehicle has advantages
over two-wheel drive vehicles in snow and ice but can skid like
any other vehicle. If so equipped, keep the vehicle in four-wheel
drive if icy or slippery conditions exist.
*
[DR21300(ALL)11/89]
Avoid sudden applications of power and quick changes of
direction on snow or ice. Apply the accelerator slowly and
steadily when starting from a full stop.
*
[DR21310(ALL)05/95]
All utility-type and Four-Wheel Drive vehicles have special
design and equipment features to make them capable of
performing in a wide variety of off-road applications. Specific
design characteristics give them higher centers of gravity than
ordinary passenger cars.
*
[DR21325(ALL)08/95]
RWARNING
Utility and four-wheel drive vehicles are NOT designed
for cornering at speeds as high as passenger cars any
more than low-slung sports cars are designed to perform
satisfactorily under off-road conditions. Avoid sharp
turns or abrupt maneuvers in these vehicles.
%*
[DR21400(ALL)03/95]
Brakes
*
[DR21500(ALL)01/93]
Front Disc Brakes
*
[DR21600(ALL)06/95]
The front disc brakes are self-adjusting. They do not require
service other than periodic inspection for pad wear.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

262
*
[DR21700( X)07/93]
Rear Disc Brakes
[DR21800( X)06/94]
The rear disc brakes are self-adjusting. They do not require any
service other than periodic inspection for pad wear.
*
[DR22100(ALL)11/89]
Hydraulic Power Brakes
[DR22200(ALL)08/94]
The hydraulic brake system is made up of two independent
hydraulic circuits. One hydraulic circuit supplies fluid to the
front disc brakes and the other hydraulic circuit supplies fluid
to the rear drum or disc brakes. These two circuits are supplied
by a common hydraulic brake fluid reservoir, with a fluid level
sensor.
*
[DR22300(ALL)11/89]
The brake light in the instrument cluster will light for low brake
fluid in the common brake fluid reservoir.
*
[DR22400(ALL)05/95]
RWARNING
An increase in pedal travel will result in reduced braking
capability. The brake system should be checked
immediately.
[DR22905(ALL)10/94]
Four Wheel Anti-lock Brake System
*
[DR22910( X)08/94]
Your vehicle is equipped with a Four Wheel Anti-lock Braking
System (4WABS). The 4WABS helps the driver to maintain
vehicle control by preventing wheel lockup during hard
braking.
*
[DR22915(ALL)03/94]
The 4WABS operates with a computer that is able to optimize
vehicle control during braking on varying tire and road
conditions by modulating the brake pressure at each of the front
wheels and the rear axle. This ªpumping actionº is similar to
the driver ªpumpingº the brakes but happens at a much faster
rate.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996