light FORD EXPLORER 1996 2.G Repair Manual

214
%*
[AS04600( X)08/95]
Using the Controls of Your Cassette Tape Player
*
[AS04700( X)08/95]
NOTE: Radio power must be on to use the cassette tape
player.
*
[AS04800( X)08/95]
How to insert a tape
*
[AS04900( X)04/95]
Your cassette tape player is equipped with power loading. Once
you insert a tape and push slightly (with the open edge to the
right), the loading mechanism draws the tape the rest of the
way in and play will begin after a momentary tape tightening
process. Display indicates“TAPE”while tape is playing.
*
[AS05000( X)01/95]
If the player is in the tape mode but not in play, pressing the
“TAPE”button will activate play. If the“TAPE”button is
pressed with no tape inserted, the display will flash“NO
TAPE”.
*
[AS05100( X)08/95]
How to locate a desired track on the tape
*
[AS05200( X)01/95]
There are six ways to quickly locate a desired selection on the
tape. You can use the fast forward, rewind, Blank Skip,“SEEK”,
“SCAN”or“SIDE 1-2”functions. Following are brief
descriptions of each:
*
[AS05300( X)09/95]


Fast forwarding the tape
*
[AS05400( X)03/95]
To fast forward the tape, press the“FF”button. The radio
will play while the tape is in fast forward. The light above
the“FF”button will blink while in the fast forward mode.
Press“FF”again or press the“TAPE”button to stop fast
forwarding. At the end of the tape, the direction
automatically reverses and plays the other side of the tape.
*
[AS05500( X)08/95]


Rewinding the tape
*
[AS05600( X)03/95]
To rewind the tape, press the“REW”button. The radio will
automatically begin playing while the tape is rewinding. The
light above the“REW”button will blink while in the rewind
mode. Press“REW”again or press the“TAPE”button to
stop rewinding.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

216
*
[AS06800( X)01/95]
How to store the tape
*
[AS06900( X)01/95]
Press the“AM/FM”button to stop the tape player and resume
radio play.
*
[AS07000( X)08/95]
Using the Dolby
B noise reduction feature
*
[AS07100( X)09/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation.“Dolby”and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
[AS07200( X)07/95]
Push thekbutton to activate. When activated, the light
above thekbutton illuminates.
*
[AS07300( X)08/95]
Tape error messages
*
[AS07400( X)08/95]
Your cassette tape player is equipped to diagnose certain
problems you may experience. Error codes are as follows:
*
[AS07500( X)01/95]
TD E1—Radio tries to change sides of tape 3 times in a 10
second span. Push“EJECT”and try another tape. If problem
persists, refer problem to qualified personnel for service.
*
[AS07600( X)01/95]
TD E2—Tape eject failure. Radio tries to eject tape and it will
not eject. Push“EJECT”to eject tape. If the tape will not eject,
refer problem to qualified personnel for service.
*
[AS07700( X)01/95]
TD E3—Loading error. Push“EJECT”to eject tape. Reload
tape. If the same error code appears in the display, try another
tape.
[AS07705( X)09/94]
Rear Seat Radio Controls (If equipped)
[AS07710( X)09/94]
Rear seat radio controls are available on vehicles equipped with
Premium and Luxury Audio Systems only.
[AS07715( X)09/94]
The rear seat radio controls are located on the rear of the center
console. These controls duplicate several radio functions of the
radio and allow the use of headphones in the vehicle.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

Electronic Sound Systems
219
*
[AS08200( X)08/95]


Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS08300( X)08/95]


If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
*
[AS08400( X)08/95]


Loose labels on cassette tapes can become lodged in the
mechanism. Remove any loose label material before inserting
a cassette.
*
[AS08500( X)08/95]


Do not leave a tape in the cassette tape player when not in
use. High heat in the vehicle can cause the cassette to warp.
%*
[AS08600( X)08/95]
Clock Operation
*
[AS08700( X)08/95]
How to view the clock mode
[AS08800( X)09/94]
Press the“CLK”button to display time. The time will continue
to be displayed until a radio or tape function is chosen. After
approximately 10 seconds, the time will again appear in the
display. To display radio or tape information only, press the
“CLK”button a second time.
[AS08900( X)09/95]
NOTE: The clock can be displayed or set whether the ignition
is on or off as long as the“CLK”button is depressed.
*
[AS09000( X)08/95]
How to set the clock
*
[AS09100( X)08/95]1.
Turn the radio on.
[AS09200( X)04/00]2.
Press and hold the“CLK”button, press the right (
a) side of
the“SEEK”button to increase hours. Press the left (
b) side
of the button to decrease hours. Press the right (
a) side of
the“TUNE”or“TUNE DISCS”button to increase minutes.
Press the left (
b) side of the button to decrease minutes.
*
[AS09300( X)09/95]
NOTE: The clock displays 12-hour time with no AM/PM
indications.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

226
%*
[AS29435(ALL)08/95]
Using the Controls of Your Cassette Tape Player
*
[AS29440(ALL)08/95]
NOTE: Radio power must be on to use the cassette tape
player.
*
[AS29445(ALL)08/95]
How to insert a tape
*
[AS29450(ALL)04/95]
Your cassette tape player is equipped with power loading. Once
you insert a tape and push slightly (with the open edge to the
right), the loading mechanism draws the tape the rest of the
way in and play will begin after a momentary tape tightening
process. Display indicates“TAPE”while tape is playing.
*
[AS29455(ALL)06/95]
NOTE: A cassette tape can be loaded with the ignition on
whether or not the radio power is on. However, with
radio power off, the cassette tape is loaded and stored.
*
[AS29465(ALL)08/95]
How to locate a desired track on the tape
*
[AS29470(ALL)08/95]
There are four ways to quickly locate a desired selection on the
tape. You can use the fast forward, rewind,“SEEK”or“SCAN”
function. Following are brief descriptions of each.
*
[AS29475(ALL)09/95]


Fast forwarding the tape
*
[AS29480(ALL)01/95]
To fast forward the tape, press the“FF”button. The radio
will begin playing until fast forward is manually stopped (by
pushing the“TAPE”button) or the end of the tape is
reached.
*
[AS29485(ALL)01/95]
At the end of the tape, the direction automatically reverses
and plays the other side of the tape.
*
[AS29490(ALL)08/95]


Rewinding the tape
*
[AS29495(ALL)01/95]
To rewind the tape, press the“REW”button. The radio will
begin playing until rewind is manually stopped (by pushing
the“TAPE”button) or the beginning of the tape is reached.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

228
[AS29550(ALL)06/95]
How to switch from tape to AM/FM mode
*
[AS29555(ALL)01/95]
Press the“AM/FM”button to stop the tape player and resume
radio play.
*
[AS29560(ALL)08/95]
Using the Dolby
B noise reduction feature
*
[AS29565(ALL)08/95]
NOTE: Noise reduction system manufactured under license
from Dolby Labs Licensing Corporation.“Dolby”and
double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
*
[AS29570(ALL)04/95]
Push thekbutton to activate Dolby B Noise Reduction. Push
again to deactivate.
[AS29620( X)10/94]
Two mini 3.5mm (1/8") jack headphone sets may be used with
the headphone jacks on your Rear Seat Radio Controls. Ford
approved headphones are also available for purchase by calling
1-800-231-4429.
*
[AS29650(ALL)08/95]
Tips on Caring for the Cassette Player and Tapes
*
[AS29655(ALL)08/95]
In order to keep your cassette tape player performing the way it
was meant to, read and follow these simple precautions:
*
[AS29660(ALL)08/95]


Using a Ford Cassette Cleaning Cartridge to clean the tape
player head after 10-12 hours of play will help maintain the
best playback sound and proper tape operation.
*
[AS29665(ALL)08/95]


Only cassettes that are 90 minutes long or less should be
used. Tapes longer than 90 minutes are thinner and subject
to breakage or may jam the tape player mechanism.
*
[AS29670(ALL)08/95]


Protect cassettes from exposure to direct sunlight, high
humidity and extreme heat or cold. If they are exposed to
extreme conditions, allow them to reach a moderate
temperature before playing.
*
[AS29675(ALL)08/95]


If a tape is loose inside the cassette, tighten it before playing
by putting your finger or a pencil into one of the holes and
turning the hub until the tape is tight.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

236
*
[AS29954(ALL)08/95]
If the sound skips:
*
[AS29955(ALL)08/95]


Badly scratched discs or extremely rough roads will cause
the sound to skip. Skipping will not damage the disc player
or scratch the discs.
*
[AS29956(ALL)01/95]
How to take care of and clean the CD Changer and
discs
*
[AS29957(ALL)01/95]
To ensure the continued performance of your CD Changer
carefully read the following precautions:
*
[AS29958(ALL)01/95]


Always handle a disc by the edge. Never touch the playing
surface.
[AS29959(ALL)06/95]


Before playing, inspect all discs for any contamination. If
needed, clean discs with an approved disc cleaner, such as
the Discwasher Compact Disc Cleaner or the Allsop 3
Compact Disc Cleaner, by wiping from the center out to the
edges. Do not use a circular motion to clean.
*
[AS29960(ALL)08/95]


Do not clean discs with solvents such as benzine, thinner,
commercially available cleaners or antistatic spray intended
for analog records.
*
[AS29961(ALL)01/95]


Do not expose the discs to direct sunlight or heat sources for
an extended period of time.
*
[AS29962(ALL)01/95]


Do not insert more than one disc into each disc slot of the
disc magazine. Doing so may damage the discs, disc
magazine or the disc changer.
*
[AS29963(ALL)01/95]


Do not insert anything other than discs into the disc
magazine.
*
[AS29964(ALL)05/95]
RWARNING
The laser beam used in the compact disc player is
harmful to the eyes. Do not attempt to disassemble the
case.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

242
*
[AS35600(ALL)08/95]2.
Terrain
*
[AS35700(ALL)08/95]
The terrain (hilly, mountainous, tall buildings) of the area over
which the signal travels may prevent the FM signal from being
noise-free.
*
[AS35900(ALL)08/95]
If there is a building or large structure between the antenna and
station, some of the signal”bends“around the building, but
certain spots receive almost no signal. Moving out of the
”shadow“of the structure will allow the station to return to
normal.
*
[AS36000(ALL)08/95]
When the radio waves are reflected off objects or structures, the
reflected signal cancels the normal signal, causing the antenna to
pick up noise and distortion. Cancellation effects are most
prominent in metropolitan areas, but also can become quite
severe in hilly terrain and depressed roadways.
*
[AS36100(ALL)08/95]
To minimize these conditions, a stereo/mono blend circuit has
been incorporated into this system. This feature automatically
switches a weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS36200(ALL)08/95]
Several sources of static are normal conditions on AM
frequencies. These can be caused by power lines, electric fences,
traffic lights and thunderstorms.
*
[AS36300(ALL)08/95]
Another reception phenomenon isStrong Signal Capture and
Overload.This can occur when listening to a weak station and
when passing another broadcast tower. The close station may
capture the more distant station, although the displayed
frequency does not change. While passing the tower, the station
may switch back and forth a few times before returning to the
original station.
*
[AS36400(ALL)08/95]
When several broadcast towers are present (common in
metropolitan areas) several stations may overload the receiver,
resulting in considerable station changing, mixing and
distortion.
File:09unasx.ex
Update:Thu Feb 29 09:08:53 1996

245
Driving Your Explorer
*
[DR00350(ALL)06/95]
Procedures for driving your vehicle will vary depending on
which type of transmission your vehicle has.
*
[DR00600(ALL)06/95]
n
a manual transmission
[DR05475( X)12/95]
n
an Automatic Overdrive Transmission 4R55E or 4R70W
[DR05700(ALL)1/96]
Automatic Transmission Operation
4R44E/4R55E/4R70W
*
[DR08715(ALL)12/95]
The 4R44E, 4R55E and 4R70W transmissions are electronically
controlled four speed overdrive automatic transmissions with
lockup torque converter. Transmission operation is controlled by
the Powertrain Control Module (PCM).
*
[DR08720(ALL)08/95]
The PCM will automatically adjust transmission operation to
make up for varying conditions. Several sensors located on the
engine and transmission such as throttle position, engine speed,
vehicle speed and transmission temperature are used by the
PCM to shift the transmission into a higher or lower gear when
required for the best performance and fuel economy. For
example, you may notice that the transmission will upshift to a
higher gear more quickly when the vehicle has not reached
normal operating temperature.
*
[DR08730(ALL)08/95]
The PCM also controls the transmission's Torque Converter
Clutch (TCC) to further raise vehicle performance and fuel
economy. The TCC will engage when the transmission operating
temperature and other conditions determined by the PCM have
been met. Engagement of the clutch may be noted as a decrease
in engine speed.
[DR08740(ALL)03/95]
To help in troubleshooting, the PCM continually performs
self-tests on the electronic control system and, if any faults are
detected, stores them in memory. The Overdrive Off Indicator
Light (O/D OFF), which is located on the instrument cluster,
may flash steadily if a malfunction has been detected. If the
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

246Overdrive Off Indicator Light is flashing, contact your Ford
dealer as soon as possible. If this condition persists, damage to
the transmission could occur.
%*
[DR08750(ALL)01/95]
Putting Your Vehicle in Gear
[DR08800(ALL)01/95]
Your vehicle's gearshift is on the steering column. The
transmission control switch is located on the end of the gearshift
lever. You can put the gearshift in any of the several positions.
[DR08915(ALL)10/94]
10-1/2 pica
art:0021373-A
The positions of the column-mounted gearshift
[DR08925(ALL)01/95]
quarter page
art:0021255-A
Transmission control switch (located on the end of the gearshift lever)
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996

248
%*
[DR09200(ALL)01/95]
R (Reverse)
*
[DR09300(ALL)08/95]
With the gearshift in the R (Reverse) position, the vehicle will
move backward. You should always come to a complete stop
before shifting into or out of R (Reverse).
*
[DR09350(ALL)01/95]
N (Neutral)
*
[DR09375(ALL)01/95]
With the gearshift in the N (Neutral) position, the vehicle can be
started and is free to roll. Hold the brake pedal down while in
this position.
%*
[DR09400(ALL)01/95]
Driving
%*
[DR09500(ALL)04/95]
When to use
j(Overdrive)
*
[DR09600(ALL)04/95]
This is the normal driving position. As the vehicle picks up
speed, automatic upshifts to second, third and fourth gears will
occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been pressed. The
transmission will shift into the correct gear when the right
speed is achieved, for the accelerator pedal position you have
chosen.
*
[DR09700(ALL)03/94]
When to use Drive
[DR09800(ALL)06/95]
You will note there is not a drive position on your gearshift
indicator. However, you will find a transmission control switch
labeled O/D ON/OFF located on the end of the gearshift lever.
Press this switch and the O/D OFF indicator light will
illuminate on the instrument cluster. With overdrive cancelled
and the O/D OFF indicator light illuminated, the transmission
will operate in gears one through three. This is useful if you
experience frequent downshift/upshift conditions, when
operating with a heavy load or in hilly terrain, or if additional
engine braking is useful. However, shift back to
j(Overdrive)
whenever practical for optimum powertrain cooling and fuel
economy. This can be accomplished by pushing the transmission
control switch again, to cancel the O/D OFF control and light.
File:10undrx.ex
Update:Thu Feb 29 09:12:36 1996