reset FORD EXPLORER 1996 2.G Owners Manual

72
%*
[ST06521(ALL)05/95]
For a warm engine:
*
[ST06522(ALL)04/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[ST06575(ALL)08/95]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter.
*
[ST06601(ALL)09/95]
After starting, allow the engine to idle for a few seconds before
driving away.
%*
[ST06775(ALL)04/95]
If the engine does not start after two attempts:
*
[ST06825(ALL)04/95]1.
Turn the ignition key to the OFF position.
*
[ST06851(ALL)04/95]2.
Press the accelerator all the way to the floor and hold it.
*
[ST06876(ALL)04/95]3.
Turn the ignition key to the START position.
*
[ST06900(ALL)04/95]4.
Release the ignition key when the engine starts.
*
[ST06925(ALL)04/95]5.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
*
[ST06951(ALL)04/95]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchlater in this chapter.
%*
[ST07300(ALL)10/95]
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast slightly
faster than its normal idle speed. It should, however, slow down
after a short time. If it does not, have the idle speed checked.
*
[ST07390(ALL)07/95]
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have
the vehicle checked.
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

74
%*
[ST08175(ALL)03/95]
If the Engine Cranks but Does Not Start or
Does Not Start After a Collision
*
[ST08200(ALL)07/95]
The Fuel Pump Shut-off Switch
*
[ST08210(ALL)10/95]
If the engine cranks but does not start or does not start after a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device intended to stop the
fuel pump when your vehicle has been involved in a major jolt.
*
[ST08215(ALL)03/95]
Once the shut-off switch is triggered, you must reset the switch
by hand before you can start your vehicle.
[ST08225(ALL)03/95]
10-1/2 pica
art:0090157-A
Fuel pump shut-off switch location
*
[ST08250(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

Starting Your Explorer
75
*
[ST08275(ALL)10/95]
If your engine cranks but does not start after a collision or
major jolt:
*
[ST08290(ALL)03/95]1.
Turn the key in the ignition to OFF.
*
[ST08300(ALL)03/95]2.
Check under the vehicle for leaking fuel.
*
[ST08325(ALL)03/95]3.
If you do not see or smell fuel, push the red reset button
down. If the button is already set, you may have a different
mechanical problem.
*
[ST08350(ALL)01/95]4.
Turn the ignition key ON for a few seconds, then turn it
OFF.
*
[ST08375(ALL)03/95]5.
Check under the vehicle again for leaking fuel.If you see or
smell fuel, do not start your vehicle again.If you do not
see or smell fuel, you can try to start your vehicle again.
*
[ST08400(ALL)03/95]6.
Check all vehicle warning lights before driving your vehicle.
[ST08450(ALL)01/95]
7-1/2 pica art:0021144-A
Reset button for fuel pump shut-off switch
File:04unstx.ex
Update:Thu Feb 29 09:22:05 1996

Warning Lights and Gauges
89
[LG06390(ALL)03/95]
Fuel Reset Light (If Equipped)
[LG06393(ALL)01/95]
Your vehicle may have a fuel reset light. The fuel reset light
will come on when you turn the ignition key to ON and the
fuel pump shut-off switch has been triggered. Refer toFuel
pump shut-off switchin the Index to find additional information.
[LG06395(ALL)10/94]
6 pica art:0021372-A
Fuel reset light
%*
[LG06400(ALL)05/94]
Battery Voltage Gauge (Voltmeter)
*
[LG06601(ALL)05/94]
This gauge shows you the battery voltage when the ignition key
is in the ON position.
*
[LG06701(ALL)05/95]
If the battery is operating under cold weather conditions, the
pointer may indicate in the upper range of the NORMAL band
while the battery is charging. If you are running electrical
accessories with the engine off or idling at a low speed, or the
battery is not fully charged, the pointer may move toward the
lower end of the NORMAL band.
*
[LG06750(ALL)05/94]
If it stays outside the NORMAL band, have your vehicle's
electrical system checked as soon as it is safely possible.
[LG06850(ALL)07/95]
7-1/2 pica art:0020539-H
Battery voltage gauge Ð mechanical cluster with tachometer
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

94
[LG12790(ALL)08/94]
10-1/2 pica art:0020873-F
Speedometer
%*
[LG12801(ALL)01/95]
Odometer
*
[LG12900(ALL)01/95]
The odometer tells you the total number of miles (kilometers)
your vehicle has been driven.
%*
[LG13000(ALL)11/94]
Trip Odometer
*
[LG13100(ALL)03/93]
If you want to track your mileage up to 999.9 miles
(kilometers), use the trip odometer. Simply set the trip odometer
to zero by pressing the reset button firmly when beginning the
distance you wish to measure.
%*
[LG13250( X)02/95]
Tachometer
*
[LG13300(ALL)05/95]
The tachometer will show you the engine's speed measured in
revolutions per minute (RPM).
*
[LG13400(ALL)05/95]
The tachometer may move slightly when the key is placed in
the ACC or ON position, with the engine off. This is normal
and does not affect the performance of the tachometer when the
engine is running.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

98
*
[LG35650( X)01/95]
To ensure accuracy, turn the ignition OFF when you fill the fuel
tank.
[LG35700( X)06/94]
NOTE: Distance to empty is calculated using a ªRunning
Average Fuel Economyº initialized by the factory. The
value is not the same as the Average Fuel Economy
Display. The Running Average Fuel Economy is based
on more than 500 miles (800 km) of driving history.
Also, the factory default for Running Average Fuel
Economy is reinitialized if the battery is disconnected.
*
[LG35750( X)05/95]
If the ªFUEL LEVEL ERRORº message is displayed, this means
that there is a problem with the fuel indication system and you
should contact your dealer for service as soon as possible.
[LG35800( X)03/95]
A second consecutive press of the FUEL RANGE switch allows
you to display how many miles or kilometers you have driven
since you last reset this feature. A press of the RESET switch
with MILE (KM) DRIVEN displayed resets the distance driven
to 0.0 miles or kilometers.
*
[LG35850( X)05/95]
Fuel Status
*
[LG35900( X)01/95]
A press of the FUEL STATUS switch allows you to display one
of two features (Fuel Remaining or Fuel Used). The first press
of the FUEL STATUS switch allows you to display the
approximate amount of fuel in the tank in whole numbers
(gallons or liters).
*
[LG35950( X)01/95]
If your fuel tank is full or nearly full, the M/C will display the
ªFULL FUEL TANKº message. If your fuel tank is empty or
nearly empty, the M/C will display the ªEMPTY FUEL TANKº
message.
[LG36000( X)04/94]
A second consecutive press of the FUEL STATUS switch allows
you to display the amount of fuel used since you last reset this
feature. A press of the RESET switch with GALLONS (LITERS)
USED displayed resets the amount to 0.0 gallons or liters used.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

Warning Lights and Gauges
99
*
[LG36050( X)01/95]
Because of factors like rounding of numbers and fuel movement
in the tank, the M/C and the service station fuel pump readings
may disagree slightly.
%*
[LG36100( X)05/95]
Fuel Economy
[LG36150( X)10/94]
A press of the FUEL ECON switch allows you to display one of
two features (Average Fuel Economy or Instantaneous Fuel
Economy). The first press of the FUEL ECON switch will allow
you to display your average fuel economy in miles/gallons or
liters/kilometers. Your M/C computes this figure using the
distance traveled and fuel used information. If you want to reset
this feature, press the RESET switch while the average fuel
economy feature is displayed. Your average fuel economy will
then use data only from after the RESET was pressed to
calculate the new average.
[LG36200( X)10/94]
A second consecutive press of the FUEL ECON switch will
allow you to display the instantaneous fuel economy, which is
the fuel economy that you get at any particular moment. For
example, you can see what your fuel economy is in heavy traffic
or on an open highway. Your fuel economy is affected by such
factors as braking, acceleration, and the type of road you are
driving on.
*
[LG36250( X)01/95]
Your vehicle must be moving for the M/C to calculate the fuel
economy. When your vehicle is not moving, instantaneous fuel
economy will be displayed at 0 miles/gallon or
99 kilometers/100 liters. When you are moving, the M/C will
display between 0 and 99 miles/gallon or between 1 and
99 kilometers/100 liters.
*
[LG36300( X)01/95]
Reset
[LG36350( X)01/95]
A press of the RESET switch will allow you to reset the current
feature being displayed. Warnings, Distance Driven, Average
Fuel Economy, Fuel Used, and your Personalized Oil Reset
Percentage are the only features which respond to the RESET
switch. Distance to Empty, Fuel Remaining, and Instantaneous
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

100Fuel Economy cannot be reset. That is, these three features are
unaffected by pushing the RESET switch.
%*
[LG36750( X)01/95]
System Check
*
[LG36800( X)01/95]
A press of the SYSTEM CHECK switch causes the M/C to cycle
through a status of each of the systems being monitored. For
each of the monitored systems, the M/C will indicate either an
OK message or a warning message for two seconds. The
sequence of the system check report is as follows:
*
[LG36850( X)01/95]
n
Engine Oil Life Left
*
[LG36900( X)01/95]
n
Engine Oil Level
*
[LG37000( X)01/95]
n
Voltage Level
*
[LG37050( X)01/95]
n
Engine Coolant Temperature
*
[LG37100( X)01/95]
n
Washer Fluid Level
[LG37150( X)04/94]
n
Head Lamps
[LG37200( X)04/94]
n
Tail Lamps
[LG37250( X)04/94]
n
Brake Lamps
[LG37300( X)06/94]
n
Air Ride System (if equipped)
*
[LG37350( X)01/95]
n
Fuel Level
*
[LG37400( X)01/95]
At normal conclusion of the system check sequence, the M/C
will display the last displayed feature before pressing the
SYSTEM CHECK switch or the warnings that are active.
*
[LG37450( X)01/95]
For two of the systems reported in the system check (Engine Oil
Life Left and Fuel Level), there are two messages to describe the
status of the system. For Engine Oil Life Left, the first message
will indicate the oil change status (OK, SOON, REQUIRED) and
the second message will indicate the oil life remaining as a
percentage. If the second message is ªOIL TEMP SIGNAL
ERRORº, this means that there is a problem with the oil
temperature sender system and you should contact your dealer
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

Warning Lights and Gauges
101 for service as soon as possible. For Fuel Level, the first message
will indicate the fuel level status (OK or LOW) and the second
message will indicate the range (distance to empty).
*
[LG37500( X)01/95]
Message center operation during system check
*
[LG37550( X)01/95]
The M/C switches will operate as follows during the System
Check sequence:
*
[LG37600( X)01/95]1.
A press of the SYSTEM CHECK switch will advance the
cycle to the next system message without waiting the two
seconds.
*
[LG37650( X)01/95]2.
A press of the RESET switch anytime during this sequence
will cause the SYSTEM CHECK cycle to conclude
immediately and the last displayed feature before pressing
SYSTEM CHECK will be displayed.
[LG37700( X)04/94]3.
A press of the RANGE, FUEL STATUS, OR FUEL
ECONOMY, switch will conclude the SYSTEM CHECK cycle
and the requested feature will be displayed.
*
[LG37750( X)01/95]4.
A press of the ENGLISH/METRIC switch will halt the
SYSTEM CHECK cycle and display, in the new mode, the
last displayed feature before pressing the SYSTEM CHECK
switch.
*
[LG37800( X)01/95]5.
A press of the OIL CHANGE RESET switch during the
sequence will cause the SYSTEM CHECK cycle to conclude
and the Oil Change Reset Procedure will begin.
*
[LG37850( X)01/95]
System Warnings
[LG37900( X)01/95]
System warnings alert you to possible problems or malfunctions
in your vehicle's operating systems. There are twelve warning
messages which can be displayed by the Message Center (M/C)
to show the status of the monitored systems. When a warning
occurs, the warning message is displayed and a tone sounds.
The warning message will appear at a brighter level if the
instrument panel is dimmed.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996

102
*
[LG37950( X)01/95]
In the event of a multiple warning situation, the M/C will cycle
the display to show all warnings by displaying each warning
message for 4 seconds.
*
[LG38000( X)01/95]
Using the message center while a warning is active
[LG38050( X)04/94]
If you want to display the operator selectable features of the
M/C while a warning is displayed, the warning message may
be removed from the M/C display by pressing the RESET
switch. The M/C will display the last selected feature if there
are no more warning messages. This allows you to use the full
functionality of the M/C after you acknowledge the warning by
pressing the RESET switch and clearing the warning message.
*
[LG38100( X)01/95]
Warning messages which have been reset are divided into two
categories. They will reappear on the display in 10 minutes
from the reset or they will not reappear until an ignition key
OFF-ON cycle. This reappearing of warning messages is a
reminder that these warning conditions still exist within the
vehicle. Warnings may be repeatedly reset. All warning
messages will reappear after an entire SYSTEM CHECK
sequence has been completed.
File:05unlgx.ex
Update:Thu Feb 29 09:04:08 1996