coolant FORD EXPLORER 1997 2.G Owners Manual

Door ajar
Illuminates when the ignition
switch is in the ON or START
position and any door or the
liftgate is open.
Check gage
Illuminates when the key is in the
ON position and the engine coolant
temperature gauge, the engine oil
pressure gauge and the fuel level
gauge need to be checked. Refer
toEngine coolant temperature
gauge, Engine oil pressure gauge
orFuel gaugein the
Instrumentationchapter for more
information.
Charging system
Briefly illuminates when the
ignition is turned on and the
engine is off. The light also
illuminates when the battery is not
charging properly, requiring
electrical system service.
Fuel reset
Illuminates when the ignition key
is turned to the ON position and
the fuel pump shut-off switch has
been triggered. For more
information, refer toFuel pump
shut-off switchin theRoadside
emergencieschapter.
DOOR
AJAR
CHECK
GAGE
FUEL
RESET
uno_check_gage
com_charging_system.01
com_fuel_reset.01
com_safety_belt.01
Instrumentation
10

INSTRUMENT CLUSTER
GAUGES
Engine coolant temperature
gauge
Indicates the temperature of the
engine coolant. At normal
operating temperature, the needle
remains within the ªNORMº area. If
it enters the red section, the
engine is overheating. Switch off
the ignition and let it cool. Refer to
Checking and adding engine
coolantin theMaintenance and
carechapter.
Engine oil pressure gauge
This shows the engine oil pressure
in the system. Sufficient pressure
exists as long as the needle
remains in the ªNORMº range.
If the gauge indicates constantly
low pressure at normal engine
speed, refer toChecking and
adding engine oilin the
Maintenance and carechapter. If
the gauge indicates a low pressure
and the engine oil level is correct,
switch off the engine immediately
0RPM x 1000
12345
6- +
H
H
L LH
C
F
E
0
20
1030405060
70
80
90
110
120000000
oooo
10020406080100
120
140
160
180
MPH km/h
H
C
H
L
com_coolant_temperature.01
com_oil_pressure.01
Instrumentation
13

Fuel economy
Press once to display your vehicle's
average fuel economy in
kilometers/liters (miles/gallons).
Press again to display the fuel
economy that your vehicle is
getting at that particular time. Your
vehicle must be moving in order
for this display to function
properly.
Reset
Press the reset control to reset the
current feature being displayed.
Warnings, distance driven, average
fuel economy, fuel used and
personalized oil reset percentage
are the only features that respond
to reset.
System check
Press the system check control to
display the status of the following
systems:
²engine oil life left
²engine oil level
²voltage level
²engine coolant temperature
²washer fluid level
²head lamps
²tail lamps
²brake lamps
ENGLISH
METRICRANGESTATUS
ECONRESETSYSTEM
CHECKOIL CHANGE
RESET
FUEL
ENGLISH
METRICRANGESTATUS
ECONRESETSYSTEM
CHECKOIL CHANGE
RESET
FUEL
ENGLISH
METRICRANGESTATUS
ECONRESETSYSTEM
CHECKOIL CHANGE
RESET
FUEL
uno_reset_system
uno_system_check
Instrumentation
18

change to ªSTART OIL LIFE AT
XXX%.º
3. Press the OIL CHANGE RESET
control until the displayed
percentage is the Personalized Oil
Reset Percentage you desire.
Check charging system
The electrical system is not
maintaining a proper voltage. Have
the electrical system checked as
soon as safely possible.
Check engine temp
The engine coolant is overheating.
Refer toEngine coolant
temperature gaugein the
Instrumentationchapter for more
information regarding the engine
coolant system.
Check exterior lamps
At least one brake lamp, rear side
marker or low beam headlamp is
burned out. To determine which
lamp is burned out:
1. Turn ignition switch to OFF to
reset M/C.
- +H
L
H
C
uno_check_charging_system uno_check_engine_temp
uno_check_exterior_lamps
Instrumentation
22

accelerator and start the engine
while holding the accelerator
down. Release accelerator when
engine starts.
4. After idling for a few seconds,
apply the brake and release the
parking brake.
Using the engine block heater
(if equipped)
An engine block heater warms the
engine coolant, which improves
starting, warms up the engine
faster and allows the
heater-defroster system to respond
quickly. They are strongly
recommended if you live in a
region where temperatures reach
Ð23ÉC (±10ÉF) or below.
For best results, plug the heater in
at least three hours before starting
the vehicle. Using the heater for
longer than three hours will not
harm the engine, so the heater can
be plugged in the night before
starting the vehicle.
To prevent electrical
shock, do not use your
heater with ungrounded
electrical systems or
two-pronged (cheater) adapters.
com_engine_heater.01
Starting
116

9. Air filter assembly
10. Engine coolant reservoir
4.0L SOHC engine
1. Windshield washer fluid
reservoir
2. Transmission fluid dipstick
3. Engine oil fill cap
4. Engine oil dipstick
5. Brake fluid reservoir
6. Battery
7. Power steering fluid reservoir
8. Air filter assembly
9. Engine coolant reservoir
9
13425
867
com_4.0L-ohc
com_5.0L
Maintenance and care
171

5.0L engine
1. Engine coolant reservoir
2. Windshield washer fluid
reservoir
3. Engine oil fill cap
4. Transmission fluid dipstick
5. Brake fluid reservoir
6. Power distribution box
7. Battery
8. Radiator cap
9. Power steering fluid reservoir
10. Engine oil dipstick
11. Ignition coil packs
12. Air filter assembly
1
236
7
54
81011912
com_check-add_oil.01
Maintenance and care
172

Checking and adding washer
fluid for the windshield
If a visual inspection shows that
washer fluid needs to be added to
the reservoir:
1. Lift the windshield reservoir
cover.
2. Add enough washer fluid to fill
the reservoir.
Checking and adding washer
fluid for the rear window
The washer fluid for both the
windshield and rear window is
contained in the engine
compartment reservoir. For
information on checking and
adding washer fluid to this
reservoir, refer to Checking and
adding washer fluid for the
windshield above.
WASHERFLUIDONLY
uno_liftgate_washer_fluid
uno_title-coolant
Maintenance and care
179

ENGINE COOLANT
MAINTENANCE
Checking and adding engine
coolant
Check the level of the coolant in
the reservoir at least once a
month. Be sure to read and
understandPrecautions when
servicing your vehiclein this
chapter.
If the engine coolant has not been
checked for a long period of time,
the engine coolant reservoir may
eventually empty. If this occurs,
add engine coolant to the coolant
reservoir. For more information on
engine coolant maintenance, refer
toAdding engine coolantin this
chapter.
Automotive fluids are not
interchangeable; do not use engine
coolant, antifreeze or windshield
washer fluid outside of its specified
function and vehicle location.
RADIATOR
COOLANT
ONLY
uno_checking-adding-coolant
com_adding_coolant.01
Maintenance and care
180

When adding engine coolant
Ford recommends Ford Premium
Cooling System Fluid, which is an
optimized formula that will protect
all metals and rubber elastomers
used in Ford engines for four years
or 80,000 km (50,000 miles).
It is neither necessary nor
recommended to use supplemental
coolant additives in your
gasoline-powered vehicle. These
additives may harm your engine
cooling system.
When you change or add engine
coolant, it is important to maintain
engine coolant concentration
between 40% (-24ÉC [-11ÉF]) and
60% (-52ÉC [-62ÉF]), depending on
your local climate conditions.
A coolant concentration below 40%
will result in a loss of freeze
protection. A concentration above
60% may cause the engine to
overheat on a warm day.
Refer toLubricant specifications
in theSpecifications and
capacitieschapter. Use only a
premium nationally-recognized
brand name engine coolant or
equivalent.
Always dispose of used
automotive fluids in a responsible
manner. Follow your community's
standards for disposing of these
types of fluids. Call your local
recycling center to find out more
about recycling automotive fluids.
com_recycled_coolant.01
Maintenance and care
181