wipers FORD EXPLORER 1997 2.G Owners Manual

Wipers
For rear wiper operation, rotate
the rear window wiper and washer
control to the desired interval
position.
Automatic ride control
(if equipped)
Your vehicle is equipped with an
automatic ride control system. This
system is designed to level your
vehicle when towing or carrying a
heavy load.
To prevent sudden vehicle
movement, turn off the air
suspension switch prior to jacking,
towing or hoisting the vehicle.
4WD CONTROL (IF EQUIPPED)
This control operates the Control
Trac 4WD. Refer toControl trac
systemin theDrivingchapter for
more information.
020
1030405060
70
80
90
110
120000000ooookm/h10020406080100
120
140
160
1800P RND21UNLEADED
FUEL ONLY
RPM x 100012345
6H
C
FERSM
SET
ACC
COAST OFF ONOFF
SRSHI LOOFF*A/C*MAX
A/C
REW
1FF
2SIDE 1-2
3
FM 1STVOL – PUSH ON
AM
FMBASS TREBBAL FADE
AUTO
SET CLKSEEKTUNE
DISCSSCAN4DOLBY SYSTEMEJTAPE CDCOMP5SHUFFLE
6
PUSH
OFFHIR. WIPE
PUSH
uno_4wd_switch
uno_fuel_pump_shut_off_ref
Controls and features
38

FUEL PUMP SHUT-OFF SWITCH
For information on the fuel pump
shut-off switch, refer toFuel
pump shut-off switchin the
Roadside emergencieschapter.
POSITIONS OF THE IGNITION
1. ACCESSORY allows the
electrical accessories such as the
radio and wipers/washer to operate
while the engine is not running.
2. LOCK locks the steering wheel
and gearshift lever and allows key
removal.
3. OFF shuts off the ignition and
accessories and allows the
gearshift and steering wheel to
move.
4. ON tests the warning lights. The
key must remain here when the
engine is running.
1
23
4
5
uno_pst-ignition
Controls and features
39

Deactivating overdrive
To deactivate overdrive, press the
control at the end of the gearshift
lever. The
O/D
OFFwill illuminate.
Deactivate overdrive when:
²driving with a heavy load
²driving in hilly terrain
²additional engine braking is
desired
WINDSHIELD WIPERS AND
WASHER
Wipers
Rotate the windshield wiper
control to the desired interval
speed.
Washer
²Press the windshield wiper
control for washer fluid
operation.
²Press once for a single wipe.
²Press and hold for a constant
cycle.0P RND21RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ON
SRS
- +H
H
L L020
1030405060
70
80
90
110
120000000oooo
km/h10020406080100
120
140
160
180
O/D
ON/OFF
uno_title_waher_wiper
uno_wipers
uno_washer
uno_speed_dependent_wipers
Controls and features
46

Speed dependent wipers
(if equipped)
This feature operates only in the
intermittent wiping mode. In
position one (slowest delay) this
feature will not function. At higher
speeds, the Speed Dependent
feature shortens the delay between
wipes when you use the variable
interval wipers. Delay will
automatically adjust at speeds
between 16 and 105 km/h (10 and
65 mph. This will help compensate
for the extra moisture that
accumulates on your windshield at
higher speeds.
Map lamps
Press the left or right control to
turn the lamp on.
Press again to turn the lamp off.
AUTOLAMP DELAY SYSTEM
(IF EQUIPPED)
The autolamp sets the headlamps
to turn on and off automatically.
The autolamp may be set to:
²turn on the lamps automatically
at night
²turn off the lamps automatically
during daylight
OPEN
GARAGE
MODELAMPLAMP
AUTO
MIRROR ON
DIMON AUTOLAMP
uno_map_lamps uno_auto-mirror
Controls and features
47

Changing your air cleaner filter
To change your air cleaner filter,
follow these steps:
1. Release the clamp locking clip
on the front portion of the
assembly.
2. Swing the left side of the
assembly open.
3. Remove the air cleaner filter
element from the open end of the
engine air cleaner assembly and
replace it with a new element.
4. Close the assembly and secure
the locking clamp.
The air cleaner filter shown is
typical of 4.0 L OHV and 5.0 L
engines. The 4.0 L SOHC is
comparable.
CHECKING AND REPLACING
WIPER BLADES
Checking wiper blades
Check the windshield wiper blades
at least twice a year or whenever
they seem to work less effectively
than usual. Substances such as
tree sap and some hot wax
treatments used by commercial car
washes can reduce the
effectiveness of wiper blades.
uno_wipers_title
uno_checking_wipers
Maintenance and care
193

To make reaching the wiper blades
easier, simply:
1. Turn the ignition to the ON
position and turn the wipers on.
2. Wait for the wipers to reach a
vertical position and turn the
ignition to LOCK.
²Do not move the wipers
manually across the windshield,
this may cause damage to both
wipers and windshield.
Inspect the wiper pivot arms on a
regular basis to ensure that they
move freely. Lubricate the pivot
points as necessary.
Replacing wiper blades
If the wiper blades do not function
properly after cleaning,
replacement of the blade assembly
or the blade element may be
necessary.
3
2
1
5
4
0P RND21RPM x 100012345
6H
C
F
E
RSM
SET
ACC
COAST OFF ON
SRS
- +H
H
L L020
1030405060
70
80
90
110
120000000oooo
km/h10020406080100
120
140
160
180
uno_replacing_wipers
Maintenance and care
194

Voltmeter (see Battery voltage
gauge) ..........................................15
Warning chimes
headlamps on ............................11
key in ignition ...........................12
safety belt .................................12
Washer fluid
reservoir ..................................179
Windows
power windows, operating .......56Windshield washer fluid and
wipers ........................................193
checking and adding fluid .....178
checking and replacing wiper
blades ...............................193,194
liftgate reservoir .....................179
operation ...................................46
specifications ..........................178
Wrecker towing .........................163
236