battery FORD F SERIES MOTORHOME AND COMMERCIAL CHASSIS 1997 10.G Owners Manual

14up cycles without a misfire condition occurring.
A warm up cycle consists of engine start from a
cold condition (engine at ambient temperature)
and running until the engine reaches normal
operating temperature.
*
[IS05600( ALL)01/96]
On the fourth engine start up, the Check Engine
Warning Light will turn off as soon as the
engine begins to crank. It is not necessary to
have the engine serviced.
*
[IS05700( ALL)01/96]
Under certain conditions, the Check Engine
Warning Light may come on if the fuel cap is
not properly installed. If the Check Engine
Warning Light comes on and you suspect that
the fuel cap is not properly installed, pull off the
road as soon as it is safely possible and turn off
the engine. Remove and replace the fuel cap,
making sure it is properly seated.
*
[IS05800( ALL)01/96]
After completing the three consecutive warm up
cycles and on the fourth engine start up, the
Check Engine Warning Light should turn off. If
the light does not go off after the fourth engine
restart, have your vehicle serviced by your
dealer or a qualified technician.
%*
[IS05900( ALL)01/96]
Charging System Light
*
[IS06000( ALL)01/96]
This light, shown as a battery symbol on your
cluster, indicates that your battery is not being
charged and that you need to have the electrical
system checked.
*
[IS06100( ALL)01/96]
one inch art:0020777-A
Charging system light
File:03ltism.ex
Update:Fri Dec 13 11:17:22 1996

15
*
[IS06200( ALL)01/96]
This light comes on every time you turn the
ignition to the ON or START position (engine
off). The light should go off when the engine
starts and the alternator begins to charge.
*
[IS06300(B FM)01/96]
If the light stays on or comes on when the
engine is running, have the electrical system
checked as soon as possible.
%*
[IS07100( ALL)01/96]
Battery Voltage Gauge (Voltmeter)
*
[IS07200( ALL)01/96]
This gauge shows you the battery voltage when
the ignition key is in the ON position.
*
[IS07300( ALL)01/96]
If you are running electrical accessories (when
the engine is off, or idling at a low speed), the
pointer may move toward the lower end of the
normal band. If it stays outside the normal band
area, have your vehicle's electrical system
checked as soon as it is safely possible.
*
[IS07400( ALL)01/96]
If the battery is operating under cold weather
conditions, the pointer may indicate in the upper
range of the NORMAL band while the battery is
charging. If you are running electrical accessories
with the engine off or idling at a low speed, or
the battery is not fully charged, the pointer may
move toward the lower end of the NORMAL
band.
*
[IS07500( ALL)01/96]
If it stays outside the NORMAL band, have your
vehicle's electrical system checked as soon as it
is safely possible.
[IS07700( E M)01/96]
quarter page art:0020863-B
Battery voltage gauge
File:03ltism.ex
Update:Fri Dec 13 11:17:22 1996

28
*
[CF29500( ALL)01/96]
Do not try to clean the windshield when the
washer fluid container is empty or activate the
washers at any time for more than 15 seconds
continuously. This could damage the washer
pump system.
*
[CF29600( ALL)01/96]
RWARNING
Always warm up the windshield with the
defroster before you use the washer fluid.
In freezing weather, the washer solution
may freeze on the windshield and obscure
your vision.
%
*
[CF29800( ALL)01/96]
Hazard Flasher
*
[CF29900( ALL)01/96]
The hazard flasher is used to alert other drivers
to hazardous situations.
*
[CF30000( FM)01/96]
The flashers will continue to flash with the brake
pedal depressed.
*
[CF30200( ALL)01/96]
The flashers work whether your vehicle is
running or not. The flashers work for up to two
hours when the battery is fully charged and in
good condition without draining the battery
excessively. If the flashers run for longer than
two hours or if the battery is not fully charged,
the battery can be drained.
*
[CF30300( ALL)01/96]
To use the hazard flasher:
*
[CF30400( ALL)01/96]
1. Push in the flasher button; it will pop out
and the lamps will begin to flash.
*
[CF30500( ALL)01/96]
2. To stop the flashers, push in the flasher
button again.
*
[CF30600( ALL)01/96]
NOTE: The flasher button will be sticking up
slightly higher when on than when off.
File:05ltcfm.ex
Update:Thu Dec 12 13:31:05 1996

82 [ER01250( M)01/96]
sixteen pica chart:0020731-E
[ER01300( ALL)01/96]
Power Distribution Box
*
[ER01350( ALL)01/96]
The high current fuses contained in the Power
Distribution Box protect your vehicle's main
electrical systems from overloads; these fuses
provide the connection between the battery and
your vehicle's electrical systems.
*
[ER01400( ALL)01/96]
The high current fuses are coded as follows: 30
amp -light green, 40 amp - orange, 50 amp - red,
60 amp -blue.
*
[ER01450( ALL)01/96]
RWARNING
Always disconnect the battery before
servicing high current fuses.
*
[ER01500( ALL)01/96]
Ford recommends that high current fuses be
replaced by a qualified technician.
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996

83
*
[ER01550( ALL)01/96]
RWARNING
Always replace the cover to the Power
Distribution Box before reconnecting the
battery or refilling fluid reservoirs.
*
[ER01600( ALL)01/96]
A blown high current fuse may be replaced but
will continue to blow until the cause of the
overload condition is corrected.
*
[ER01650( ALL)01/96]
RWARNING
Always replace a fuse with one that has
the specified amperage rating. Using a
fuse with a higher amperage rating can
cause severe wire damage and could start
a fire.
[ER01950( M)01/96]
half page art:0020964-A
Power Distribution Box
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996

92 % [ER18400( M)01/96]
eight pica chart:0020726-A
%*
[ER19300( ALL)01/96]
Jump-Starting Your Vehicle
*
[ER19400( ALL)01/96]
Your vehicle's battery may die if you leave the
lights on or any electrical equipment on after
you turn the engine off. If this happens, you
may be able to jump-start your vehicle with a
booster battery.
*
[ER19450( ALL)01/96]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[ER19500( ALL)01/96]
RWARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
%*
[ER19550( ALL)01/96]
RWARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996

93 %
*
[ER19600( ALL)01/96]
RWARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
*
[ER19650( ALL)01/96]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[ER19750( ALL)01/96]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
*
[ER19800( ALL)01/96]
Preparing Your Vehicle
*
[ER19850( ALL)01/96]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
*
[ER19900( ALL)01/96]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[ER19950( ALL)01/96]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996

94
*
[ER21000( ALL)01/96]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
*
[ER21100( ALL)01/96]
5. Turn on the heater fan in both vehicles.
Turning on the fan helps protect the
electrical system from voltage surges. Turn
off all other switches and lights in both
vehicles to prevent possible damage to either
vehicle's electrical systems.
%*
[ER21200( ALL)01/96]
Connecting the jumper cables
*
[ER21300( ALL)01/96]
1. Connect one end of the first jumper cable to
the positive (+) terminal of the discharged
battery. (You can connect either jumper cable
to the positive (+) terminal, as long as you
use the same cable for both positive
terminals.) Most jumper cables have a red
cable and a black cable. The red cable is
generally used for the positive terminals and
the black for the negative ones.
*
[ER21500( ALL)01/96]
2. Connect the other end of the first cable to
the positive (+) terminal of the booster
battery.
*
[ER21600( ALL)01/96]
3. Connect one end of the second cable to the
negative (S) terminal of the booster battery
Ð NOT to the discharged battery.
*
[ER21700( ALL)01/96]
4. Connect the other end of the second cable to
a good metallic surface on the engine or
frame of the disabled vehicle.
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996

95
*
[ER21800( ALL)01/96]
RWARNING
Do not connect the end of the second
cable to the negative (S) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
*
[ER21900( ALL)01/96]
one third page art:0020262-C
Attaching jumper cables
*
[ER22000( ALL)01/96]
Jump-Starting
*
[ER22100( ALL)01/96]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[ER22200( ALL)01/96]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[ER22300( ALL)01/96]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996

96 %
*
[ER22400( ALL)01/96]
Removing jumper cables
*
[ER22500( ALL)01/96]
1.Always remove the jumper cables in the
reverse order.Remove the negative (S) end
of the jumper cable from the metallic surface
on the engine or frame of the disabled
vehicle.
*
[ER22600( ALL)01/96]
2. Remove the negative (S) cable from the
booster battery.
*
[ER22700( ALL)01/96]
3. Remove the positive (+) cable from the
booster battery.
*
[ER22800( ALL)01/96]
4. Remove the other end of the positive (+)
cable from the discharged battery.
*
[ER22900( ALL)01/96]
After the vehicle is started, let it idle for a while
to let the engine ªrelearnº its idle conditions.
Drive it around for a while with all electrical
accessories turned off to let the battery recharge.
Driveability may be deteriorated slightly until all
drive modes are ªrelearned.ºYou may need to
use a battery charger to fully recharge the
battery.
*
[ER23000( ALL)01/96]
If you need to replace your battery, seeBattery
in theMaintenance and Carechapter.
File:10lterm.ex
Update:Fri Dec 13 11:23:45 1996