bulb FORD F150 1997 10.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: F150, Model: FORD F150 1997 10.GPages: 219, PDF Size: 2.21 MB
Page 197 of 219
REPLACING BULBS
Replacing exterior bulbs
It is a good idea to check the
operation of the following lamps
frequently:
²Headlamps
²Tail lamps
²Brakelamps
²High-mount brakelamp
²Backup lamps
²Hazard flashers
²Turn signals
²License plate lamp
²Fog lamps
²Interior overhead lampsf12_replacing_bulbs
Maintenance and care
198
Page 198 of 219
Do not remove lamp bulbs unless
they will be replaced immediately.
If a bulb is removed for an
extended period of time,
contaminants may enter the lamp
and affect performance.
Replacing headlamp bulbs
Handle a halogen
headlamp bulb carefully
and keep out of children's reach.
Grasp the bulb only by its plastic
base and do not touch the glass.
The oil from your hand could
cause the bulb to break the next
time the headlamps are
operated.
1. Make sure that the headlamp
control is in the position.
2. Open the hood.
3. At the back of the headlamp,
pull clips rearward and up 19 mm
(about 3/4 in.) to release the
headlamp assembly.
f12_headlamps_turnsignals
Maintenance and care
199
Page 199 of 219
4. Slide headlamp assembly
forward and off of guide ribs to
expose the back of the bulb and
wiring connector.
5. Remove the electrical connector
from the bulb by grasping the wire
and pulling it rearward.
6. Remove bulb retainer ring by
turning it counterclockwise about
1/4 turn, then slide the ring off the
plastic base.
7. Without turning, carefully pull
bulb assembly out of headlamp
assembly.
8. Insert the glass end of the new
bulb into the headlamp assembly
socket. When the grooves in the
plastic base are aligned, push the
bulb into the socket until the
plastic base contacts the rear of
the socket.
9. Slip bulb retaining ring over the
plastic base and lock the ring into
the socket by turning it clockwise
until you feel a ªstop.º
10. Push the electrical connector
into the rear of the plastic base
until it ªsnaps.º
Maintenance and care
200
Page 200 of 219
11. Straighten alignment pins,
making them parallel with the
outer edges of the attachment
standoff.
12. Carefully insert the headlamp
assembly into the vehicle making
sure the alignment pins are
inserted into the proper holes and
into the guide ribs.
13. Hold the headlamp assembly
snugly against the vehicle and
push down on the clips to lock the
lamp into position.
Replacing parking lamp/turn
signal bulbs
1. Remove screw from the top of
lamp assembly.
Maintenance and care
201
Page 201 of 219
2. Disengage lamp assembly (it has
a snap fit).
3. Remove the electrical connector
from the bulb by grasping the wire
and pulling it rearward.
4. Remove bulb retainer ring by
turning it counterclockwise about
1/4 turn, then slide the ring off the
plastic base.
5. Without turning, carefully pull
bulb assembly out of parking lamp
assembly.
6. Insert the glass end of the new
bulb into the parking lamp
assembly socket. When the grooves
in the plastic base are aligned,
push the bulb into the socket until
the plastic base contacts the rear
of the socket.
7. Slip bulb retaining ring over the
plastic base and lock the ring into
the socket by turning it clockwise
until you feel a ªstop.º
8. Push the electrical connector
Maintenance and care
202
Page 202 of 219
into the rear of the plastic base
until it ªsnaps.º
9. Align top and bottom ribs of
parking lamp assembly with
corresponding slots on front of
vehicle.
10. Push gently until parking lamp
assembly seats (you will hear a
snap).
11. Replace screw removed in step
1.
Replacing foglamp bulbs
1. Disconnect the electrical
connector from the back of the
foglamp assembly.
2. Twist, then pull the bulb from
the foglamp assembly.
3. Install the new bulb.
4. Connect the electrical connector
to the back of the foglamp
assembly.
f12_foglamps
f12_tail_lamps
Maintenance and care
203
Page 203 of 219
Replacing tail lamp/backup
lamp bulbs
1. Remove the two bolts from the
inside of the tailgate.
2. Carefully pull the tail lamp and
backup lamp assembly from the
tailgate pillar by releasing the two
retaining tabs.
3. Disconnect the bulb connector.
4. Pull out the bulb to be replaced.
5. Install a new bulb.
6. Carefully insert the tail lamp
and backup lamp assembly,
snapping the two retaining tabs
into place.
7. Install the two bolts.
Replacing license plate lamp
bulbs
1. Carefully pull the license plate
lamp lens from the rear bumper.
2. Remove the bulb to be replaced
and install a new bulb.
3. Install the license plate lamp
lens.
f12_license_plate_lamps f12_dome_lamp
Maintenance and care
204
Page 204 of 219
Replacing dome lamp bulb (if
equipped)
1. Carefully pull the dome lamp
lens from the lamp assembly.
2. Remove the dome lamp bulb
and replace it with a new bulb.
3. Carefully snap the dome lamp
lens into the dome lamp assembly.
Replacing dome/map lamp bulb
(if equipped)
1. Carefully pull the dome/map
lamp lens from the lamp assembly.
2. Remove the dome/map lamp
bulb and replace it with a new
bulb.
3. Carefully snap the dome lamp
lens into the dome/map lamp
assembly.
Replacing engine compartment
lamp bulb (if equipped)
1. Open the hood.
2. Carefully pull the engine
compartment lamp bulb from the
lamp assembly and replace with a
new bulb.
f12_dome_map_lamp
f12_engine_compart
f12_exterior_bulb_specs
Maintenance and care
205
Page 205 of 219
Exterior bulb specifications
Function Number of
bulbsTrade number
Front park/turn lamps 2 3157NAK
Foglamps 2 9006
Headlamps 2 9007
Rear turn/sidemarker 2 3157NAK
AIMING HEADLAMPS
The alignment of your headlamps
should be checked if:
²Oncoming motorists frequently
signal you to turn off your
vehicle's high beams when you
do not have the high beams on.
²The headlamps do not seem to
give you enough light to see
clearly at night.
²The headlamp beams are
pointed substantially away from
a position slightly down and to
the right.
See your Ford dealer for precise
headlamp adjustment.
Cleaning and caring for your
vehicle
Refer to the ªCustomer Assistance
Guideº for a list of Ford-approved
cleaners, polishes and waxes.
f12_aiming_hlamps
f12_cleaning_your_vehicle
com_cleaning_caring.01
com_washing_vehicle.01
Maintenance and care
206