brake FORD F150 2005 11.G Quick Reference Guide

HEADLAMP AND PANEL DIMMER CONTROLRotate the control clockwise one position from off to turn on the parking lamps.
Rotate two positions from off to also turn on the headlamps. Rotate counterclockwisefrom off to activate autolamp (if equipped), which provides lightsensitive automaticon/off control of the exterior lights and keeps them on for a short period of time afterthe ignition is turned off. When the control is in any position except high beams or off, pull the controltoward you to activate the foglamps (if equipped).
Use the panel dimmer control, located to the right of the headlamp control, to adjust the brightness of
the instrument panel during the headlamps and parking lamps operation. Rotate to the full up position,past the detent, to turn on the interior lamps. Rotate to the full down position, past the detent, toprevent the interior lights from illuminating when doors are opened.
POWER ADJUSTABLE PEDALS(if equipped)
Press and hold the top end of rocker control to adjust the accelerator and brake
pedal away from you. Hold the lower end of the control to move the pedals towardyou. Adjust the pedals only when the vehicle is stopped and the gearshift lever is in
the P (Park) position.
If equipped with memory function, the adjustable pedals, along with the driver's seat, can be
automaticallypositioned in two programmable positions using the control located on the driver's seat.
Refer to your Owner's Guide for instructions on how to use this memory feature.
SERVICE ENGINE SOON LAMPIlluminates briefly when the ignition is turned to the ON position to ensure the
system is functional. If the light comes on after the engine is started, refer to yourOwner's Guide. This lamp will illuminate if the fuel cap is not fully secured. In addition,
"Check fuel cap" will appear in the message center display. Make sure that the fuel capis secure by turning it clockwise 1/4 of a turn until it stops.
ABS WARNING LAMPIlluminates briefly when the ignition is turned to the ON position. If the light
comes on after the engine is started, refer to your Owner's Guide.
SPEED CONTROL(if equipped)
To set the speed control, press the ON button and release. Accelerate to the
desired speed and press the SET button and release. Once the system is engaged, an
icon will appear in the instrument cluster. To increase speed, tap the SET button and thespeed will increase in small increments each time, or use the accelerator pedal to reach
desired speed and then press SET. To reduce speed, press and hold CST until desired speed is reached.
Release or tap the CST button and speed will decrease in small increments. Also, you can depress the
brake pedal until desired speed is reached and press SET. Press RES/RESUME to return the vehicle to apreviously set speed if the vehicle is traveling more than 30 mph (48 km/h).
FOR REDUNDANT STEERING WHEEL CONTROLS(if equipped). To set the speed control,
press the right side of the ON/OFF switch. Accelerate to the desired speed and press the right side of the
CST/SET button and release. Once the system is engaged, an icon will appear in the instrument cluster.T
1
2
3
4
5

To increase speed, tap the SET button and the speed will increase in small increments each time, or use
the accelerator pedal to reach desired speed and then press SET. To reduce speed, press the left side of
the CST/SET button until desired speed is reached. R
elease or tap the left side of the CST/SET button
and speed will decrease in small increments.Also, you can depress the brake pedal until desired speed
is reached and press SET. Press RES/RESUME to return the vehicle to a previously set speed if the
vehicle is traveling more than 30 mph (48 km/h).
MESSAGE CENTER(if equipped)
With the ignition on, the message center displays important vehicle
information through a constant monitor of vehicle systems. The system will notify you of potential vehicle problems by displaying
warnings, followed by a long indicator chime. You may select the INFO or SETUP buttons on the message
center to display trip odometer, odometer, compass, distance to empty, average fuel economy, and tripelapsed drive time. The RESET button may be used to reset selected functions in the INFO and SETUP
menus. For more information about message center functions, please refer to your Owner's Guide.
FOURWHEEL DRIVE CONTROL(if equipped)
2H (2WD HIGH) delivers power to the rear wheels only and is the optimal
position for smoothness and fuel economy. 4H (4x4 HIGH) provides mechanically
locked fourwheel drive power to all four wheels. 4L (4x4 LOW) provides mechanically
locked fourwheel drive when extra power at reduced speeds is required. With eitheran electronic shift 4WD system or manual 4WD system, to shift from 2H to 4H move the control at any
forward speed up to 55 mph (88 km/h). To shift to or from 4L, bring the vehicle to a stop and keep thebrake pedal depressed. Next, place the gearshift in N (Neutral), and then move the control to or from 4L.
Some mechanical noise may be heard when the system engages. This is normal and no service isrequired. Note: The manual 4WD system has an N (Neutral) position in the transfer case. This settingoverrides the transmission and puts the vehicle in Neutral regardless of gearshift position. This settingshould only be used when towing the vehicle.
INDASH CD6/MP3 DISC AUDIO SYSTEM(if equipped)
Please see reverse side for more details.
PASSENGER AIRBAG DEACTIVATED LAMP(if equipped) Please refer to
the Seating and Safety Restraints section of your Owner's Guide for informationon
the PassengerAirbag Deactivated Lamp.
AUXILIARY POWER POINT (12V)An auxiliary power point is located on the instrument panel. For SuperCab and
SuperCrew vehicles, there is an additional auxiliary power point located on the lower
rear side of the center console that is accessible from the rear seats. Do NOT plug
optional electrical accessories into the cigarette lighter.
6
7
8
9
10