high beam FORD F150 2016 13.G Quick Reference Guide

7
566
8
4231
1
3
5
6
7
8
4
LED SIDE-MIRROR SPOT
LAMPS CONTROL*
The spot lamps are on the forward-
facing side of the exterior mirrors.
With the lighting control switch in
the parking lamps, headlamps or
autolamps position, press the buttons
located above the lighting control
switch to activate the left-hand or
right-hand side spot lamps. Once
switched on, the spot lamps light the
area in front of and to the side of your
vehicle. Adjust the aim of the spot
lamps by moving the exterior
mirrors' positions.
LIGHTING CONTROL

Headlamps off.

Parking lamps on.

Headlamps on.

Autolamps* on.
Automatically switches
the exterior lamps on
or off based on
available daylight.

Fog lamps on. Press the
control to switch the fog
lamps on or off. You can
switch the fog lamps on when
the lighting control is in any
position except off and the
high beams are not on. ELECTRIC
PARKING BRAKE*
On certain models, the electric parking
brake replaces the conventional foot
brake. The operating switch is on the
instrument panel, to the left of the
steering column.
To apply the electric parking brake,
make sure the transmission is locked
into park (P), and then pull the

switch up. The brake system warning
lamp then lights to confirm that the
parking brake is applied.
To release the electric parking brake,
switch the ignition on, press the brake
pedal, and then manually press the
switch down. The brake system
warning lamp then turns off to confirm
the parking brake is released.
ADJUSTABLE
FOOT PEDALS*
Move the brake and accelerator pedals
by using the control. The vertical
control is to the left of the steering
column and on the instrument panel.
The horizontal control is on the left
side of the steering column.
Press the left arrow
to move the
pedals away from you.
Press the right arrow
to move the
pedals closer to you.
Adjust the pedals only after stopping
your vehicle and placing it in park (P). INFORMATION DISPLAY
PRODUCTIVITY SCREEN*
Monitor and control important vehicle
information and features through the
information display.
•
Press the up or down arrows

to scroll through and highlight the
options within a menu.
• Press the right arrow
to enter into
a sub-menu.
• Press the left arrow
to exit a menu.
• Press OK to choose and confirm a
setting or message.
You can even customize your views
using MyView.
Refer to the Information Displays
chapter in your Owner’s Manual for
more details.
ADAPTIVE
CRUISE CONTROL*
Automatically adjust your speed to
maintain a set distance between your
vehicle and the vehicle in front of you
in the same lane. Set the gap distance
between your vehicle and the vehicle
in front of you by pressing GAP+ or
GAP– or
and controls on the
steering wheel.
Note: Driving aids do not replace the
need to watch where the vehicle is
moving and brake where necessary.
Refer to the Cruise Control chapter in
your Owner’s Manual for more details.
4 – 5
POWER TILT-TELESCOPE
STEERING COLUMN*
Use the control on the side of the
steering column to adjust
the position.
To tilt: Press the top or bottom
of the control.
To telescope: Press the front or
rear of the control. The column
moves to the full up and away
position when you switch the
ignition off. It returns to your
previous setting when you switch
the ignition on. You can enable
or disable this feature in the
information display.
Instrument Panel2POWERSCOPE®
POWER-FOLDING,
POWER-ADJUSTABLE
TELESCOPING
MIRRORS*
To telescope both mirrors at the
same time, make sure you switch
your vehicle on (with the ignition
in accessory mode or the engine
running) and then:
1. Press and release the

or control.
2. Press the adjustment control
to position the mirrors.
• Press the left arrow
to
extend the mirrors out. Press
the right arrow
to retract
the mirrors in.
• Press the up or down arrow
to fold the mirrors
toward the window glass.
Press the up or down arrow
to fold the mirrors out.
Note: Moving the mirrors 10 or
more times within one minute, or
repeated folding and unfolding
of the mirrors while holding the
control down during full travel,
may disable the system to protect
the motors from overheating.
Wait approximately three minutes
with the vehicle running, and up
to 10 minutes with the vehicle
off, for the system to reset and
for function to return to normal.
*if equipped
*if equipped