wheel FORD FIESTA 2007 Workshop Manual

206-02-1 Drum Brake 206-02-1
SECTION 206-02 Drum Brake
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS PAGE
SPECIFICATIONS
Specifications.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206-02-2
Drum Brake Specification ........................................................................\
.................. 206-02-2
DESCRIPTION AND OPERATION
Drum Brake ........................................................................\
................................................. 206-02-3
Overview ........................................................................\
..................................................... 206-02-3
DIAGNOSIS AND TESTING
Drum Brake ........................................................................\
.................................................
REMOVAL AND INSTALLATION
Brake Drum ........................................................................\
............................ (122750) 206-02-6
Brake Shoes ..... .. . . . . .. . . .. .. .. . . .. . . .. . . .. . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . (1 2 285 0)
206-02-7
( Wheel Cylinder ........................................................................\
.................. (12 305 0) 206-02-9
Brake Backing Plate .... ........................................................................\
........... (12 31 3 0)
206-02-1 0
procarmanuals.com

206-02-2 Drum Brake 206-02-2
SPECIFICATIONS
Lubricants, Fluids, Sealers and Adhesives
I Grease - brake shoe adjuster I SAM-1C1024-A I
Silicon dielectric compound
I Super DOT 4 brake fluid I ESD-M6C57-A I
Specification
ESA-MI C171-A
Drum Brake Specification
I Brake shoe width I 36 mm I
-- -- - -
New brake drum nominal diameter
Worn brake drum discard diameter
*
1 worn brake shoe lining discard thickness * I I mm I
203 mm
204 mm
I * When the discard diameterlthickness has been reached, install a new brake drumlbrake shoes.
Toraue S~ecifications
I Description I Nm
I Wheel spindle retaining bolts I 70 I 52 I - I
I Wheel speed sensor retaining bolt I 10 I - I 89 I
2006.0 Fiesta 1212006 G22863en
Wheel cylinder retaining bolts
Brake hose to wheel cylinder union 10
17 -
13
procarmanuals.com

206-02-6 Drum Brake 206-02-6
REMOVAL AND INSTALLATION
Brake Drum(l2 275 0)
Removal Remove the dust cap.
I. Remove the parking brake control trim panel.
6. Remove the brake drum.
2. Loosen the parking brake cable adjustment 1. Remove and discard the wheel hub retaining
nut to the end of the thread. nut.
2. Remove
the drum.
Discard the retaining clip.
3. Release the parking brake. Installation
4. Remove the wheel and tire. For additional 1 ~CAUTION:Rotate the drum ten times in information, refer to Section 204-04 [Wheels
the opposite direction when tightening the
and Tires].
wheel hub retaining nut to prevent damage
5. N0TE:If the dust cap is damaged on removal to
the bearing.
a new dust cap must be installed during
N0TE:lnstall a new wheel hub retaining nut.
installation.
N0TE:lnstall a new parking brake cable retaining
clip.
To install, reverse the removal procedure.
2. Adjust the parking brake cable. For
additional information, refer to
Section
206-05 [Parking Brake and
Actuation].
procarmanuals.com

206-02-7 Drum Brake 206-02-7
REMOVAL AND INSTALLATION
Brake Shoes(l2 285 0)

Materials 5. Detach the wheel speed sensor from the
backing plate.
Name Specification
Silicon dielectric
compound
Removal
I. Remove the parking brake control trim panel.
Grease - brake shoe
adjuster
2. Loosen the parking brake cable adjustment
nut to the end of the thread.
SAM-1 C1024-A
Discard the retaining clip.
6. Remove the brake drum.
7. Remove the hold down springs.
3. Release the parking brake.
4. Remove the wheel and tire. For additional
information, refer to Section
204-04 [Wheels
and Tires]. *' ACAUTION:DO not damage the wheel
cylinder boots.
N0TE:Hold the wheel cylinder pistons in place with
a rubber band.
2006.0 Fiesta 1212006 GI 49887en
procarmanuals.com

206-02-8 o Drum Brake 206-02-8
REMOVAL AND INSTALLATION
Detach the brake shoes from the wheel 11. Disconnect the parking brake cable from
cylinder. the
brake shoe.
I
9. Remove the brake shoe return springs. 12. Remove the brake shoes.
Installation
I. N0TE:Make sure that the brake shoe adjuster
is fully released.
N0TE:lnstall a new parking brake cable retaining
clip.
To install, reverse the removal procedure.
Apply grease to the brake shoe adjuster strut.
Clean the backing plate and apply silicon
dieletic compound to the brake shoe contact
points.
10. Remove the brake shoe adjuster from the 2, Adjust the parking brake cable. For
brake shoes.
additional information, refer to
Section
206-05 [Parking Brake and
Actuation].
2006.0 Fiesta 1212006 G149887en
procarmanuals.com

206-02-9 Drum Brake 206-02-9
REMOVAL AND INSTALLATION
Wheel Cylinder(l2 305 0)
\* , General Equipment 2. Bleed the brake system. For additional
Brake hose clamp information, refer to Section 206-00 [Brake
System
- General Information].
Removal
A CAUTI0N:lf brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
1. Remove the brake shoes.
For additional information, refer to Brake
Shoes in this section.
2m ACAUTION:C~~ the brake tube to prevent
fluid loss or dirt ingress.
Disconnect the brake tube from the wheel
cylinder.
1. Using a suitable brake hose clamp, clamp
the brake hose.
2. Disconnect the brake tube.
3. Remove the wheel cylinder.
Installation
I. To install, reverse the removal procedure.
2006.0 Fiesta 1212006 GI 49888en
procarmanuals.com

206-02-1 0 Drum Brake 206-02-1 0
REMOVAL AND INSTALLATION
Brake Backing Plate(l2 31 3 0)
General Equipment
I Electric hand drill I
I Blind rivet gun-hand I
Removal
I. Remove the wheel cylinder.
For additional information, refer to Wheel
Cylinder in this section.
2. Detach the parking brake cable from the
backing plate.
I. Depress the retaining clip.
2. Detach the cable.
3.
Remove the brake backing plate.
Using a suitable electric hand drill remove
the rivets
Installation
1. To install, reverse the removal procedure.
Using a suitable blind rivet gun-hand, install
new rivets.
2006.0 Fiesta 1212006 G149889en
procarmanuals.com

206-03-5 Front Disc Brake 206-03-5 - - --- -- -
REMOVAL AND INSTALLATION
Brake Pads(l2 234 0)
i Special Tool(s) Remove the brake hose retaining clip.
Retractor, Brake Caliper
Piston
206-005
Materials
Name Specification
I Silicone Grease I ESE-MlC171-A I
Removal
Brake Fluid - Super
I DOT4 4m &AUTION:S~~~~~~ the brake caliper to
prevent load being placed on the brake hose.
ESD-M6C57-A
Detach the brake caliper from the brake
caliper anchor plate.
A CAUTI0N:If brake fluid is spilt on the
paintwork, the affected area must be 1. Remove the brake caliper retaining bolt
immediately washed down with cold water. covers (if equipped).
2. Remove the brake caliper retaining bolts.
I. Remove the wheel and tire. I i For additional information, refer to: Wheel
and Tire
(204-04 Wheels and Tires, Removal
and Installation).
2. Remove the brake caliper retaining clip.
3. N0TE:Make a note of the position of the
brake hose to aid installation.
Detach the brake hose from the brake hose
support bracket.
5. Remove the brake pads.
2006.0 Fiesta 1212006 G149890en
procarmanuals.com

206-03-7 Front Disc Brake 206-03-7
REMOVAL AND INSTALLATION
Brake Caliper(l2 243 0) /
' General Equipment 2. Disconnect the brake hose.
Brake hose
clamp
Materials
Name Specification
I Silicone Grease I ESE-MlC171-A I
Removal
A CAUTI0N:If brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
1. Remove the wheel and tire.
4. Remove the brake caliper.
For additional information, refer to: Wheel
and Tire
(204-04 Wheels and Tires, Removal I. Remove the brake caliper retaining bolt
and Installation). covers (if equipped).
2. Remove the brake caliper retaining clip. 2. Remove the brake caliper retaining bolts.
5. Remove the brake pads.
3' ACAUTION:C~~ the brake hose to prevent
fluid loss or dirt ingress.
N0TE:Use a wrench to prevent the brake hose
from rotating.
Disconnect the brake hose from the brake
caliper.
I. Using a brake hose clamp, clamp the brake
hose.
Installation
ACAUTION:D~ not twist the brake hose
when connecting the brake hose to the brake
caliper to prevent damage to the brake hose.
- -
2006.0 Fiesta 1212006 G149891en
procarmanuals.com

206-04-3 Rear Disc Brake 206-04-3
DESCRIPTION AND OPERATION
Rear Disc Brake
Rear Wheel Hub and Disc Brake Assembly
Item Description Item Description
I 1 I Beam axle
2
3
I plate assembly
2006.0 Fiesta 1212006 G427693en
5
Brakediscshield
Brake caliper and brake caliper anchor
4
Wheel hub retaining nut
8
Dust cap
6
7
Wheel speed sensor ring
Brake disc
Wheelhub
9 Wheel
spindle
procarmanuals.com