transmission oil FORD FIESTA 2007 Service Manual

308-0349 Manual Transmission/Transaxle 308-03-49
DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES
Assembly 3. Using the special tool, install the differential
taper roller bearings.
I 1. N0TE:Do not lubricate the differential
bearings.
Carefully clean and check all components
and coat them with clean transmission oil
before assembly.
2. N0TE:lnstall a new differential pinion snap
ring.
lnstall the ring gear and the differential
pinions.
1. Using the old bolts, carefully attach the ring
gear to the differential case.
1 I
Discard the ring gear bolts.
2. lnstall the two differential pinions, plastic
thrust elements and using a suitable drift,
install the pin and snap ring.
3. lnstall the differential pinions and rotate them
90 degrees in the differential case.
3. N0TE:lnstall new ring gear retaining bolts.
N0TE:Do not rest the differential on the lower
differential taper roller bearing.
Using the special tool, install the differential
taper roller bearings and tighten the ring gear
retaining bolts.
1 . lnstall new ring gear retaining bolts and
tighten the bolts working diagonally.
2. lnstall the vehicle speed sensor (VSS) sensor
ring.
2006.0 Fiesta 1212006 G21541 en
procarmanuals.com

308-03-52 Manual Transmission/Transaxle 308-03-52
ASSEMBLY
Transaxle(l6 11 8 8)
Special Tool(s)
Installer, Wheel Hub Bearing
Conelseal
205-296 (1 5-085)
15085
I I Adapter for 303-060 I
21 02402
Mounting Stand
303-435 (2 1 -1 87)
Adapter for
303-060
303-060-02 (2 1 -024-02)
I I Installer, Halfshaft Seal
Special Tool(s)
Installer, lnput Shaft Bearing
308-041 (1 6-020)
I I Installer, Extension Housing I
1 press I
16031
I Dial indicator gauge I
Installer, lnput Shaft Snap
Ring
308-076 (1 6-03 1
)
I Magnetic stand for dial indicator gauge
Seneral Equipment
I Blanking plugs I
I M8 x 50 mm bolt I
Thread die
Materials
Name Specification
1 Sealant I ESEE-M4G1008-A I
1 Transmission Oil I WSD-M2C200-C I
I Oil Pan Sealer I WSK-M2G348-A5 I
I Silicon Sealer I WSE-M4G323-A4 I
High Temperature
Grease
1. Clean and check all parts carefully before
reassembly.
Apply clean transmission oil to all running
surfaces.
2006.0 Fiesta 1212006 G23119en
procarmanuals.com

308-03-53 Manual Transmission/Transaxle 308-03-53
ASSEMBLY
*' ACAUTION:M~~~ sure the output shaft 2. lnstall the fifth and reverse gear selector
roller bearing is installed with the scribed shaft.
text uppermost.
Using the special tool, install the output shaft
roller bearing and the output shaft bearing
cup.
1. lnstall the oil funnel.
2. lnstall the output shaft roller bearing.
3. Using the special tool, install the differential
bearing cup.
4, lnstall the fifth and reverse gear selector
shaft, and the shift lock.
1, lnstall the shift lock.
5. lnstall the reverse gear idler.
6. lnstall the differential assembly and the
permanent magnet.
7. Prepare the input and output shaft for
installation.
1. Engage the input shaft and output shaft.
2. Move the first and second gear shift forks to
the installation position.
2006.0 Fiesta 1212006 G23119en
procarmanuals.com

308-03-59 Manual Transmission/Transaxle 308-03-59
ASSEMBLY
35. N0TE:lnstall a new fifth gear synchronizer
assembly snap ring.
1 , N0TE:Use a new selector fork retaining pin.
lnstall the fifth gear synchronizer assembly
and the selector fork.
lnstall the retaining pin.
lnstall the snap ring.
36. Apply sealer evenly to the inside edge of
the fifth gear housing mating face.
37. lnstall the fifth gear housing cover.
38. lnstall the selector lever.
lnstall the bellows.
39. Engage the fifth gear.
Turn the selector shaft clockwise as far as
possible and push the shaft in.
40. N0TE:lnstall new halfshaft oil seals.
Using the special tools, install both halfshaft
oil seals (left-hand side shown).
2006.0 Fiesta 1212006 G23119en
procarmanuals.com

308-03-60 Manual Transmission/Transaxle 308-03-60
ASSEMBLY
41. lnstall the gearshift cable bracket. 2. lnstall the retaining pin.
42. N0TE:lnstall a new snap ring. 45m &AUTION:U~~~~ suitable adhesive tape,
Install the gearshift lever. cover
the input shaft splines to prevent
damage to the input shaft oil seal.
1. lnstall the snap ring.
2. lnstall the protective cap (if equipped). Position
the input shaft oil seal.
TIE
43. lnstall the selector mechanism cover. 46m ~CAUTION:DO not apply grease on any
parts of the clutch slave cylinder.
lnstall the clutch slave cylinder.
44. lnstall the vehicle speed sensor (VSS) (if
equipped).
1. Push in the VSS.
Tighten the bolts evenly. In doing so, press
the input shaft oil seal into the transmission
housing.
2006.0 Fiesta 1212006 G23119en
procarmanuals.com

308-03-64 Manual Transmission/Transaxle 308-03-64
INSTALLATION
13. Connect the vehicle speed sensor (VSS) 16. Raise and support the vehicle. For
electrical connector (if equipped). additional information, refer to
Section 100-02 [Jacking and Lifting].
17. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than 18 degrees.
The outer joint must not be bent more than
45 degrees.
ADO not damage the halfshaft oil seal.
Attach the right-hand halfshaft and the
intermediate shaft to the transaxle.
14' ACAUTION:~~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
Connect the clutch slave cylinder supply
line.
Install the spring clip.
15. Attach the coolant expansion tank to the
bracket. 18.
N0TE:lnstall a
new center bearing cap and
locknuts.
Install the intermediate shaft center bearing
cap.
I. Install the center bearing cap.
2. Attach the heat shield.
3. Install the locknuts.
19. CAUTIONS:
Asupport the halfshaft. The inner joint
must not be bent more than 18 degrees.
The outer joint must not be bent more than
45 degrees.
2006.0 Fiesta 1212006 GI I 3293en
procarmanuals.com

308-03-65 Manual Transmission/Transaxle 308-03-65
INSTALLATION
ADO not damage the halfshaft oil seal. 21. Install the engine support insulator.
/ / AMake sure the snap ring is correctly
seated.
N0TE:lnstall a new snap ring.
Attach the left-hand halfshaft to the
transaxle.
20m ACAUTION:M~~~ sure that the heat shield
is installed to prevent damage to the ball
joint.
N0TE:The lower arm pinch bolt must be installed ' ' from the rear of the wheel knuckle.
22. Install the accessory drive belt cover.
Attach the lower arm to the wheel knuckle
on both sides.
Vehicles without automated gearshift
23. Attach the gearshift cables to the bracket
and turn the abutment sleeves
counterclockwise.
2006.0 Fiesta 1212006 GI 13293en
procarmanuals.com

308103168 Manual Transmission/Transaxle 308103168
INSTALLATION
37. Connect the powertrain control module
(PCM) electrical connector to the PCM.
38. Install the front wheels and tires. For
additional information, refer to
Section
204-04 wheels and Tires].
Vehicles without automated gearshift
39. Adjust the gearshift cables. For additional
information, refer to Section
308-00
[Manual Transmission/Transaxle and Clutch
- General Information].
40. Bleed the clutch system. For additional
information, refer to Section
308m00
[Manual Transmission/Transaxle and Clutch
- General Information].
All vehicles
41. Install the battery tray. For additional
information, refer to Section
41 4-01
[Battery, Mounting and Cables].
42. With the vehicle on a level surface, fill the
transaxle until the oil level is just below the
bottom of the filler hole.
Vehicles with automated gearshift
43m ACAUTION:T~~ worldwide diagnostic
system (WDS) gearshift actuator bleed
option must be carried out
if any part of the
clutch hydraulic system is opened or any
new components are installed.
N0TE:When the WDS gearshift actuator bleed
option is selected, the learn transmission and learn
clutch parameter options will automatically be
completed.
Bleed the clutch system. For additional
information, refer to Section
308-00 [Manual
Transmission/Transaxle and Clutch - General
Information].
2006.0 Fiesta 1212006 GII 3293en
procarmanuals.com