303-01 FORD FIESTA 2007 Workshop Manual

303-00-6 Engine System - General Information 303-00-6
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Damaged gaskets or mating
surfaces.
- Cylinder head gasket is
damaged or mating face are
warped.
- Valve stem oil seals are
worn and engine oil can
enter the combustion
chamber between the valve
stem and the valve stem
guide.
Piston ring or cylinder liner
wear.
Damaged cylinder liners or
excessive clearance of engine
components.
- Pistons
- Piston rings (clearance in
groove and end gap)
- Cylinder liners
CHECK the gaskets and
mating surfaces for damage.
Remove the cylinder head.
CHECK the mating faces, cylinder
head gasket and the evenness of
the cylinder head and engine
block mating faces. INSTALL new valve
seals.REFER
to:
Valve Seals (303-01 Engine
-
1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V
(Sigma)/l .6L Duratec-I 6V
(Sigma), In-vehicle Repair),
Valve Seals (303-01 Engine
-
1.3L Duratec-8V (Rocam), In-
vehicle Repair),
Valve Seals (303-01 Engine
-
2.OL Duratec-HE (M14), In-
vehicle Repair),
Valve Seals (303-01 Engine
-
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Valve Seals (303-01 Engine
-
1.6L Duratorq-TDCi (DV)
CHECK the running surfaces
and clearances of the individual
engine components. INSTALL
new components as necessary.
INSTALL a new cylinder block
if necessary.
CHECK the pistons.
REFER to: Piston Inspection
(303-00 Engine System
-
General Information, General
Procedures).
CHECK the piston rings.
REFER to: (303-00 Engine
System
- General Information)
Piston Ring-to-Groove Clear- ance (General Procedures),
Piston Ring End Gap (General
Procedures).
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-9 Engine System - General Information 303-00-9
DIAGNOSIS AND TESTING
Symptom Possible Sources
Action
lgnition system (petrol engines
only).
CHECK the ignition system.
REFER to:
Engine
lgnition (303-07 Engine
Ignition, Diagnosis and
Testing),
Engine
lgnition (303-07 Engine
lgnition - 2.OL Duratec-HE
(M14), Diagnosis and
Testing).
Incorrect valve timing. CHECK and adjust the valve
timing. REFER to:
Timing
Belt (303-01 Engine -
1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-I 6V
(Sigma)ll .6L Duratec-I 6V
(Sigma), I n-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Crankshaft
Pulley (303-01
Engine
- 2.OL Duratec-HE
(M14), In-vehicle Repair),
Timing
Belt (303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing
Belt (303-01 Engine -
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
Broken or damaged timing
beltltiming chain or
pulleylsprocket.
CHECK the timing beltltiming
chain and sprocketslpulleys.
INSTALL new components as
necessary. REFER to:
Timing
Belt (303-01 Engine -
1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-I 6V
(Sigma), In-vehicle Repair),
Timing
Belt (303-01 Engine -
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Timing Chain (303-01 Engine
- 2.OL Duratec-HE (M14), In-
vehicle Repair),
Timing
Belt (303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
2006.0 Fiesta 12,2006 GI 52554en
procarmanuals.com

303-00-1 I Engine System - General Information 303-00-1 I
DIAGNOSIS AND TESTING
Symptom Possible
Sources Action --
Turbocharger (diesel engine
only).
CHECK the turbocharger.
REFER to:
Turbocharger (303-04
Fuel
Charging and Controls -
Turbocharger - 1.4L
Duratorq-TDCi (DV) Diesel,
Diagnosis and Testing),
Turbocharger (303-04
Fuel
Charging and Controls -
Turbocharger - 1.6L
Duratorq-TDCi (DV) Diesel,
Diagnosis and Testing).
Incorrect valve timing. Timing
beltltiming sprocket or
pulleylsprocket damaged. CHECK
and adjust the
valve
timing. REFER to:
Timing
Belt (303101 Engine -
I .25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V
(Sigma), In-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Crankshaft
Pulley (303-01
Engine
- 2.OL Duratec-HE
(M14), In-vehicle Repair),
Timing
Belt (303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing
Belt (303-01 Engine -
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
Ignition timing incorrect (petrol
engines only).
CHECK the electronic engine
controls.
REFER to: Electronic Engine
Controls (303-1 4 Electronic
Engine Controls, Diagnosis
and Testing).
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-1 2 Engine System - General Information 303-00-1 2
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Noisy running Engine auxiliary components
loose or damaged. CHECK
engine auxiliary
components for damage or
looseness. REFER to:
Timing Belt
(303-01 Engine -
1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-I 6V
(Sigma), In-vehicle Repair),
Timing Chain
(303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Timing Chain
(303-01 Engine
- 2.OL Duratec-HE (M14), In-
vehicle Repair),
Timing Belt
(303-01 Engine -
I .4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing Belt
(303-01 Engine -
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
Noisy running, misfiring, back-
firing or knocking
Incorrect fuel DETERMINE which type of fuel
was last put in the tank (note
the country specific fuel
specifications).
Valve timing incorrect, timing
beltlchain or pulleylsprocket
damaged.
Water in fuel or fuel contamin-
ated.
CHECK and adjust the valve
timing. REFER to:
CHECK the fuel system for
water or other contamination.
Timing Belt
(303-01 Engine -
1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-1 6V
(Sigma)/l.GL Duratec-1 6V
(Sigma), In-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
I n-vehicle Repair),
Crankshaft Pulley
(303-01
Engine - 2.OL Duratec-HE
(M14), In-vehicle Repair),
Timing Belt
(303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing Belt
(303-01 Engine -
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
2006.0 Fiesta 1212006 f GI 52554en
procarmanuals.com

303-00-1 3 Engine System - General Information 303-00-1 3
DIAGNOSIS AND TESTING
Symptom
Noisy running or valve train
noise
Possible Sources Action
Valve clearance too large due
to
faulty valve tappets or worn
valve train components.
Timing
belt or timing chain
damaged.
INSTALL new hydraulic lash
adjusters or adjust the valve
clearance. REFER to:
Valve Clearance Adjustment
(303-01 Engine
- 1.25L
Duratec-I 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L
Duratec-I 6V (Sigma),
General Procedures),
Camshaft
Followers (303-01
Engine - 1.3L Duratec-8V
(Rocam), In-vehicle Repair),
Valve Clearance Adjustment
(303-01 Engine
- 2.OL
Duratec-H E (M 14), General
Procedures),
Hydraulic Lash Adjuster (303-
01 Engine
- I .4L Duratorq-
TDCi (DV) Diesel, In-vehicle
Repair),
Camshaft (303-01 Engine
-
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
INSTALL a new timing belt or
timing chain. REFER to:
Timing Belt (303-01 Engine
-
1.25L Duratec-1 6V
(Sigma)ll.4L Duratec-I 6V
(Sigma)/l .6L Duratec-1 6V
(Sigma), In-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Timing Chain (303-01 Engine
- 2.OL Duratec-HE (M14), In-
vehicle Repair),
Timing
Belt (303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel,
In-vehicle Repair),
Timing
Belt (303-01 Engine -
1.6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-1 4 Engine System - General Information 303-00-1 4
DIAGNOSIS AND TESTING
Symptom
Possible Sources
Action
Timing belt or timing chain
incorrectly tensioned.
CHECK the timing belt or
timing chain tension. INSTALL
a new timing belt or timing
chain as necessary. REFER to:
Timing Belt (303-01 Engine
-
I .25L Duratec-1 6V
(Sigma)/l.4L Duratec-1 6V
(Sigma)/l .6L Duratec-1 6V
(Sigma), In-vehicle Repair),
Timing Chain (303-01 Engine
- 1.3L Duratec-8V (Rocam),
In-vehicle Repair),
Timing Chain (303-01 Engine
- 2.OL Duratec-HE (M14), In-
vehicle Repair),
Timing Belt
(303-01 Engine -
1.4L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair),
Timing Belt (303-01 Engine
-
I .6L Duratorq-TDCi (DV)
Diesel, In-vehicle Repair).
Noisy running or engine noise
Engine components
- Pistons
- Piston rings
- Connecting rod big end,
main bearing or thrust
bearing journals
- Connecting rods bent or
damaged.
CHECK the engine compon-
ents for wear or damage. Make
sure all components are within
specification. INSTALL new
components as necessary.
Engine - Oil Leaks
NOTE: Before installing new gaskets or seals, make
sure that the fault is clearly established.
If the oil leak cannot be identified clearly by a visual
inspection, carry out an ultraviolet
(UV) test:
Ultraviolet (UV) Testing
1. Clean the engine and transmission with a
suitable cleaning fluid.
2. Pour the UV-test fluid in accordance with the
quantity specified by the manufacturer through
the oil filler neck into the engine and install the
oil filler cap.
A WARN1NG:Vehicles with manual transaxle,
shift the transaxle into Neutral. Failure to
follow this instruction may result in
personal injury.
3. Start the engine and let it run for about five
minutes. 4.
Switch off the engine.
N0TE:lf no leak can be found, road test the vehicle
under various loads and check the engine for leaks
again.
5. Check the engine for oil leaks using a suitable
UV lamp.
'
6. Rectify any leaks found and check the engine
for oil leaks.
Measure the compression pressure
N0TE:The powertrain control module (PCM)
receives an error message when the fuel pump
relay is removed or electrical components are
disconnected. This error message must be deleted
from the fault memory using WDS after completing
the compression test.
(' ,
'I N0TE:Valve clearance must be set correctly before
performing a compression test. Make sure the
engine is at the normal operating temperature.
2006.0 Fiesta 1212006 GI 52554en
procarmanuals.com

303-00-33 Engine System - General Information 303-00-33
GENERAL PROCEDURES
Camshaft Bearing Journal Clearance
1. N0TE:Make sure that the following stages The value that is read off is the bearing
are followed exactly. The tappets or followers clearance.
must be removed to carry out this
measurement.
N0TE:Make sure that the camshaft is to
specification.
N0TE:The bearing caps and journals should be
free from engine oil and dirt.
Position on a width of plastigage on the
bearing cap.
Insert the camshaft, without lubrication, into
the cylinder head.
Position
a plastigage strip, which should be
equal to the width of the bearing cap, on the
bearing journal.
2. Following the tightening specification, install
the camshaft bearing caps. Refer to the
corresponding Section 303-01.
3.
N0TE:Do not strike the bearing caps.
Remove the camshaft bearing caps, refer to
the corresponding Section 303-01.
'4. Using the Plastigage, read off the
measurement.
Compare the width of plastigage with the
plastigage scale.
2006.0 Fiesta 1212006
procarmanuals.com

303-01 A-I Engine
. 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-I
6V (Sigma)ll . 6L Duratec-1 6V (Sigma)
303-01 A-I
SECTION 303-01A Engine . 1.25L Duratec-1 6V
(Sigma)/l.4L Duratec-I 6V (Sigma)/l . 6L Duratec-1 6V
(Sigma)
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
........................................................................\
.............................................. Specifications
Engine Data
. 1.25L ........................................................................\
................................
Engine Data . I . 4L ........................................................................\
..................................
Engine Data . 1.6L ........................................................................\
..................................
Oil pressure ........................................................................\
.............................................
Engine Oil Capacity . - 1.25Ll1.4L ........................................................................\
............
Engine Oil Capacity - 1.6L ........................................................................\
......................
Valve Clearance - 1.25LlI . 4L ........................................................................\
..................
Valve Clearance - 1.6L ........................................................................\
............................
Cylinder block - 1.25L ........................................................................\
.............................
Cylinder block - 1.4L ........................................................................\
...............................
........................................................................\
............................... Cylinder block - 1.6L
........................................................................\
.......................................... Cylinder head
Piston
-1.25L ........................................................................\
...........................................
Piston -1.4L ........................................................................\
.............................................
Piston - l.6L ........................................................................\
............................................
PAGE
DESCRIPTION AND OPERATION
........................................................................\
......................................................... Engine 303-01A-9
........................................................................\
.................... 1.4Ll1.6L Duratec 16V engine 303-01A-9
DIAGNOSIS AND TESTING
........................................................................\
......................................................... Engine 303-01A-12
GENERAL PROCEDURES
........................................................................\
....................... Valve Clearance Adjustment 303-01 A-I 3
IN-VEHICLE REPAIR
Crankshaft Front Seal ........................................................................\
......... (21 467 0)
Valves ........................................................................\
..................................... (21 21 5 4)
Intake Manifold ........................................................................\
....................... (21 183 0)
Valve Cover ........................................................................\
............................ (21 141 0)
Valve Seals ........................................................................\
............................. (21 238 0)
Camshafts ........................................................................\
........................ (21 284 0)
Camshaft Seal ........................................................................\
................... (21 288 0)
Timing Belt ........................................................................\
.......................... (21 304 0)
Exhaust Manifold ........................................................................\
.................... (21 187 0)
Cylinder Head ........................................................................\
...................... (21 163 0)
Oil Pan ........................................................................\
............................. (21 154 0)
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)/l .6L Duratec-1 6V (Sigma)
Oil Pump ...
Crankshaft
REMOVAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (21 71 4 0) 303-01
A-66
Rear Seal.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (21 468 4)
303-01
Engine ..... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303-01 A-70
Engine - Vehicles With: Automatic Transaxle ................................................................... 303-01A-82
DISASSEMBLY
Engine
........................................................................\
............................. (21 134 8) 303-01A-95
DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES
Cylinder Head..
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (21 165 6) 303-01A-105
ASSEMBLY
Engine
........................................................................\
.................................... (21 134 8) 303-01A-108
INSTALLATION
Engine..
.... .. .... .................... . . . ............ ...... ....... . ...... . . ...... . . . . . . . . . . ....... . . . . ....... . . 303-01A-122
Engine - Vehicles With: Automatic Transaxle.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303-01 A-1 34
procarmanuals.com

Engine - 1.25L Duratec-I 6V (Sigma)ll.4L
303-01 A-9 Duratec-1 6V (Sigma)/l .6L
Duratec-1 6V (Sigma) 303-01 A-9
DESCRIPTION AND OPERATION
Engine
i
1.4U1.6L Duratec 16V engine
Overview
The 1.4L and 1.6L Duratec 16V inline engines have The intake air routing and the air cleaner housing
already been installed on Focus vehicles under the have
also been changed. The pistons and piston
name of the Zetec-SE engine. rings
have been modified. The cylinder head cover
Details of this engine have been modified. The is
made of plastic.
routing of the pipes in the intake manifold has been
In addition, the auxiliary drive belt is an elastic
revised, and for the first time the throttle valve is multi-groove belt without a separate tensioning
electronically controlled. roller.
2006.0 Fiesta 1212006 GI 7901 7en
procarmanuals.com