light FORD MONDEO 2006 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine 3.Insert the second key in theignition switch and turn to positionII.
4.Turn the second key back toposition 0 and remove from theignition switch − the key codingmode is now activated.
5.If an uncoded key is now insertedin the ignition switch and turnedto position II within 10 seconds,this key is coded to the system.
6.After the coding process iscompleted, remove the key fromthe ignition switch. Wait fiveseconds for the system to beactivated.
If coding is not completed correctly,the indicator light flashes after theignition is switched on with the newlycoded key and the engine will notstart.
Repeat the coding process afterwaiting 20 seconds with the ignitionswitched on (position II).
Coding erasure
With two keys coded for your vehicleyou can make all the other codedkeys unusable, e.g. after loss:
Complete each of the following stepswithin five seconds.
Carry out the first four steps underKey coding, then continue asfollows:
•Insert the second key in theignition switch and turn to positionII.
•Remove the key from the ignitionswitch.
•Insert the first key in the ignitionswitch, turn to position II and hold.The control light flashes for fiveseconds.
•If the ignition is switched off duringthese five seconds, the erasureprocess is terminated and no keyis erased.
•If the erasure process iscompleted, all the other keys,apart from the two used forerasure, can no longer be usedunless recoded.
Additional keys can now be coded.
42
Engine immobiliserE66508

Downloaded from www.Manualslib.com manuals search engine ADJUSTING THE
WINDSCREEN WASHER
JETS
The eye ball jets can be adjustedprecisely using a pin.
HEADLAMP WASHERS
WARNING
Do not operate the washer formore than 10 seconds at a time,and never when the reservoir isempty.
The headlamp washers operatewhen the exterior lights are switchedon and the windscreen washer isused. The system is supplied fromthe washer fluid reservoir.
CHECKING THE WIPER
BLADES
Check the wiper blades on yourvehicle for roughness by running thetip of your fingers over the edge ofthe blade. Clean the wiper blade lipswith water applied with a softsponge.
51
Wipers and washersE73425 E73427 E66644

Downloaded from www.Manualslib.com manuals search engine LIGHTING CONTROL
Lighting control positions
OffA
Side and tail lampsB
HeadlampsC
Parking lampsD
Parking lamps
Push in and turn anticlockwise.
Autolamps
WARNING
The autolamps feature is anauxiliary system which is notintended to relieve the driver of hisresponsibility for the vehicle’s exteriorlighting.
When the switch is set to AUTO, thedipped beam headlamps will switchon and off automatically dependingon the ambient light.
Note: Main beam can be activatedonly when the autolamps feature hasturned on the headlamps.
If the headlamps switch offautomatically with main beamactivated, the next time theautolamps feature switches on theheadlamps, main beam will still be on.Dipped beam may be selected bypulling the multi-function levertowards the steering wheel.
Main/dipped beam
To switch over pull the lever towardsthe steering wheel.
53
LightingABCE72161 E72162 E72168

Downloaded from www.Manualslib.com manuals search engine Headlamp flasher
Pull the lever slightly towards thesteering wheel.
FRONT FOG LAMPS
Note: It is not possible to switch onthe front fog lamps when the lightingswitch is set to AUTO. To switch onthe front fog lamps, switch off theautolamps feature.
Switch on the headlamps 1 and pullout the control switch one position2.
The front fog lamps should be usedonly when visibility is considerablyrestricted by fog, snow or rain.
REAR FOG LAMPS
WARNING
The rear fog lamps may only beused when visibility is restrictedto less than 50 m and must not beused when it is raining or snowing.
Note: On vehicles not equipped withfront fog lamps the control switchcan be pulled out only one position.
Note: It is not possible to switch onthe rear fog lamps when the lightingswitch is set to AUTO. To switch onthe rear fog lamps, switch off theautolamps feature.
Switch on the exterior lamps 1 andpull out the control two positions 2.
54
LightingE72168 E72163 12E72164

Downloaded from www.Manualslib.com manuals search engine ADJUSTING THE
HEADLAMPS
Vehicles with Xenonheadlamps
Vehicles with Xenon headlamps arefitted with automatic headlamplevelling.
The headlamps can be adjusted fordriving on the left or right hand sideof the road i.e. when travellingabroad. This adjustment should onlybe carried out by an expert.
HEADLAMP LEVELLING
Without headlamp levellingA
With headlamp levellingB
The level of the headlamp beams canbe adjusted according to the vehicleload. Turn the thumbwheeldownward to lower the beams, andupward to raise them.
55
LightingABE72165 E65990

Downloaded from www.Manualslib.com manuals search engine Recommended headlamp levelling control positions
Control positionLoad
EstateSaloonLoad inluggagecompart-ment1
Persons
with self-level. susp.withoutself-level.susp.
Rear seatsFront seats
000--1-2
01212-31-2
02222max.131-2
123232max.1-1
1 See Technical specifications (page 173).
2Control position must be increased by 0.5 on vehicles with 2.0 l Duratorq-TDCi
or 2.5 l Duratec-VE engines and automatic transmission. Higher controlpositions (+1) may be necessary when towing a trailer.
HAZARD WARNING
FLASHERS
Press the switch to turn on or off. Thehazard warning flashers can also beoperated when the ignition is off.
DIRECTION INDICATORS
56
LightingE72166 E72167

Downloaded from www.Manualslib.com manuals search engine Briefly tap the lever up or down andthe direction indicators will flash threetimes.
INTERIOR LAMPS
OffA
Door contactB
OnC
On some models, with the switch inposition B, the interior lamps will stayon for a while after the doors areshut. They will switch off immediatelywhen the ignition is switched on.
When parking your vehicle with thedoors open for a long period of time,the interior lamps are switched offautomatically after 30 minutes.
To switch the lamps back on switchon the ignition (position II) for a shorttime.
Reading lamps
CHANGING A BULB
WARNINGS
On vehicles fitted with Xenonheadlamps, have the headlampbulbs changed by an expert. Thereis a risk of injury due to high voltage.
During operation, the bulbs andtheir surroundings get hot.Switch off the lights and let the bulbscool down before replacing them.
Note: Have the headlamp alignmentchecked after each replacement ofa bulb.
Always switch off lights and ignitionbefore replacing any bulb.
Never touch the glass of the bulbs.Fit only bulbs having a UV filter.Always replace a faulty bulb with anew one of the same type. Afterreplacing a bulb, check that the lightsoperate correctly.
57
LightingABCE72170 E72171

Downloaded from www.Manualslib.com manuals search engine Headlamps, side lamps,direction indicators
Note: It is necessary to remove theheadlamp assembly to remove anyof the bulbs.
Removing the headlampassembly
Open the bonnet.
Remove the rotary clip on both endsof the radiator grille and pull out theradiator grille.
Grasp one of the tabs and pull outthe retaining pin. Repeat with theother tab.
Carefully pull out the headlampassembly and disconnect the wiringconnector.
Front direction indicators
21 watt spherical bulb, orange
•Turn the bulb holder anticlockwiseand pull out.
•Turn the bulb under slightpressure anticlockwise andremove it.
•Replace the bulb.
When installing in the reverse order,pay attention to the guide tabs.
Side lamps
5 watt wedge base bulb
58
LightingE72536 E72537 E72538

Downloaded from www.Manualslib.com manuals search engine •Turn the cover anticlockwise, andremove.
•Using a flat-bladed screwdriver,carefully prise out the socket.
•Pull out the bulb and replace it.
When installing in the reverse order,pay attention to the guide tabs.
Opening the headlampassembly
•Disconnect the wiring connector.
•Release the clips on the rear ofthe headlamp assembly andremove the cover.
When installing in the reverse order,make sure the clips engage properly.
Headlamps – dipped beam
H7, 55 watt halogen bulb
•Disconnect the wiring connector.
•Release the wire clip and pull outthe bulb.
•Replace the bulb.
Install in the reverse order.
Headlamps – main beam
H1, 55 watt halogen bulb
59
LightingE72539 E72540 E72541

Downloaded from www.Manualslib.com manuals search engine •Disconnect the wiring connector.
•Release the wire clip and pull outthe bulb.
•Replace the bulb.
Install in the reverse order.
Side repeater indicator
5 watt wedge base bulb
•Slide the lamp assemblydownwards and pull it out.
•Grasp the bulb holder, turn thelamp housing anticlockwise andremove it.
•Pull the bulb out.
Install in the reverse order.
Approach lamps
Please consult an expert.
Fog lamps (vehicles withsport bumpers)
H3, 55 watt halogen bulb
60
LightingE72542 E72543 E72169 E72544