wiring FORD MONDEO 2006 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 2006, Model line: MONDEO, Model: FORD MONDEO 2006 2.GPages: 198, PDF Size: 4.69 MB
Page 60 of 198
Downloaded from www.Manualslib.com manuals search engine Headlamps, side lamps,direction indicators
Note: It is necessary to remove theheadlamp assembly to remove anyof the bulbs.
Removing the headlampassembly
Open the bonnet.
Remove the rotary clip on both endsof the radiator grille and pull out theradiator grille.
Grasp one of the tabs and pull outthe retaining pin. Repeat with theother tab.
Carefully pull out the headlampassembly and disconnect the wiringconnector.
Front direction indicators
21 watt spherical bulb, orange
•Turn the bulb holder anticlockwiseand pull out.
•Turn the bulb under slightpressure anticlockwise andremove it.
•Replace the bulb.
When installing in the reverse order,pay attention to the guide tabs.
Side lamps
5 watt wedge base bulb
58
LightingE72536 E72537 E72538
Page 61 of 198
Downloaded from www.Manualslib.com manuals search engine •Turn the cover anticlockwise, andremove.
•Using a flat-bladed screwdriver,carefully prise out the socket.
•Pull out the bulb and replace it.
When installing in the reverse order,pay attention to the guide tabs.
Opening the headlampassembly
•Disconnect the wiring connector.
•Release the clips on the rear ofthe headlamp assembly andremove the cover.
When installing in the reverse order,make sure the clips engage properly.
Headlamps – dipped beam
H7, 55 watt halogen bulb
•Disconnect the wiring connector.
•Release the wire clip and pull outthe bulb.
•Replace the bulb.
Install in the reverse order.
Headlamps – main beam
H1, 55 watt halogen bulb
59
LightingE72539 E72540 E72541
Page 62 of 198
Downloaded from www.Manualslib.com manuals search engine •Disconnect the wiring connector.
•Release the wire clip and pull outthe bulb.
•Replace the bulb.
Install in the reverse order.
Side repeater indicator
5 watt wedge base bulb
•Slide the lamp assemblydownwards and pull it out.
•Grasp the bulb holder, turn thelamp housing anticlockwise andremove it.
•Pull the bulb out.
Install in the reverse order.
Approach lamps
Please consult an expert.
Fog lamps (vehicles withsport bumpers)
H3, 55 watt halogen bulb
60
LightingE72542 E72543 E72169 E72544
Page 63 of 198
Downloaded from www.Manualslib.com manuals search engine •Loosen the screw in the fog lampbezel. Prise out the fog lampbezel.
•Loosen the screws, and pull outthe lamp assembly.
•Disconnect the wiring connector.
•Pull the bulb out and replace it.
Install in the reverse order.
Fog lamps (ST variants)
H7, 55 watt
•Remove the screws in the foglight bezel.
•Prise out the ring around the lensand the fog light bezel.
•Loosen the screws and pull outthe light assembly.
•Remove the wiring connector.
•Turn the back of the lightassembly anti-clockwise and pullit out.
•Pull the bulb out and replace it.
Install in the reverse order.
Rear lamps (4-door and 5-door)
Open the tailgate.
61
LightingE72545 E72546 E72547
Page 64 of 198
Downloaded from www.Manualslib.com manuals search engine From inside the luggagecompartment, release the rotary clipsof the rear light assembly cover.
Remove the cover.
Press the two red tabs towardseacht other and separate theassembly from the light housing.
Remove the wiring connector.
Direction indicator 21 wattA
Brake/tail lamp 21/4 wattB
Tail lamp 5 wattC
Reversing lamp H1 halogenbulbD
Tail lamp 5 wattE
Rear fog lamp 21 wattF
Turn the bulb anticlockwise underslight pressure, and remove it.
Replace the bulb.
Install in the reverse order. Afterinstallation, check that the lightsoperate correctly.
Rear lamps (Estate)
Open the tailgate.
From inside the luggagecompartment, remove the top rearlight assembly cover. The bottomcover is fastened with clips. Removethe cover.
Unscrew the two wing nuts from thelight assembly. Make sure the wingnuts do not fall into the opening.
Gently pull out the light assembly.
62
LightingE72548 E72549 E72550
Page 65 of 198
Downloaded from www.Manualslib.com manuals search engine Turn the bulb anticlockwise underslight pressure, and remove it.
Brake lamp 21 wattA
Direction indicator 21 watt,orangeB
Reversing lamp 21 watt,halogen bulbC
Rear fog lamp/tail lamp 21/4wattD
Replace the bulb.
Install in the reverse order. Afterinstallation, check that the lightsoperate correctly.
Central brake lamp (4-door)
5 watt wedge base bulbs (5x)
Pull the cover off.
•Disconnect the wiring connector,and take out the lamp assembly.
•Press the catches and pull off thecover.
•Pull the bulb out and replace it.
Install in the reverse order.
Central brake lamp (5-doorand Estate)
5 watt wedge base bulbs (5x)
63
LightingE72551 E72552 E72553 E72555 E72554
Page 66 of 198
Downloaded from www.Manualslib.com manuals search engine Remove the two screws, and takeoff the cover.
•Disconnect the wiring connector,and take out the lamp assembly.
•Press the catches and pull off thecover.
•Pull the bulb out and replace it.
Install in the reverse order.
Number plate lamp
5 watt festoon
•Loosen the two screws, andremove the lamp assembly.
•Pull the bulb out and replace it.
Install in the reverse order.
Front interior lamp
10 watt festoon bulb
•Switch off the interior lights(left-hand switch position).
•Prise out the lamp assembly in therecess at the side opposite theswitch with a flat-bladed screwdriver.
•Remove the reflector.
•Replace the bulb.
Install in the reverse order.
Rear interior lamp
10 watt festoon bulb
64
LightingE72555 E72556 E72557 E72558
Page 96 of 198
Downloaded from www.Manualslib.com manuals search engine Pull one or both unlocking knobs inthe luggage compartment and foldthe seatback forwards.
Returning the seatback toits upright position
The seatback must engage in thelatches on both sides. The seat beltsmust be forward of the seatback.
Folding rear seat cushionsand seatback forwards
5-door and Estate
Pull the loop between the seatcushion and the seatback and foldthe seat cushion forward. Removethe head restraints of the rear seatsand fold the seatback forward.
Note: When the red marking in theunlocking button is visible, theseatback is not fully engaged.Release the seatback and repeat theprocedure until the red marking is nolonger visible. If the seatbeltintegrated into the seatback doesnot function properly, check theunlocking mechanism.
When returning the seats to theiroriginal positions, make sure the seatbelts will function properly and arepositioned in front of the seatback.On vehicles with heated rear seats,make sure the heating system wiringdoes not get stuck or damaged.
94
SeatsE72322 E72323