fuel FORD PROBE 1996 2.G Owners Manual

7
*
[IN08200(ALL)04/95]
Cleaning Chrome and Aluminum Parts
*
[IN08300(ALL)04/95]
Wash chrome and aluminum parts with a mild
detergent. Do not use steel wool, abrasive
cleaners, fuel or strong detergents.
%*
[IN08400(ALL)04/95]
Cleaning Plastic Parts
*
[IN08500(ALL)04/95]
Some of your vehicle's exterior trim parts are
plastic. Clean with a tar and road oil remover if
necessary. Use a vinyl cleaner for routine
cleaning.
*
[IN08600(ALL)04/95]
Do not clean plastic parts with thinners, solvents
or petroleum-based cleaners.
%*
[IN08700(ALL)04/95]
If you have your vehicle rustproofed, remove
oversprayed rustproofing with a tar and road oil
remover. If rustproofing is not removed from
plastic and rubber parts, it can cause
deterioration.
*
[IN08725(ALL)04/95]
Because your vehicle's side mouldings are
painted in lacquer, do not use thinners or
solvents to clean them.
File:prinp.ex
Update:Fri Jun 23 19:39:18 1995

42
%*
[ST04100(ALL)03/95]
Fuel-Injected Engines
*
[ST04200(ALL)03/95]
When starting a fuel-injected engine,the most
important thing to remember is to avoid
pressing down on the accelerator before or
during starting. Only use the accelerator when
you have problems getting your vehicle started.
SeeStarting Your Enginein this chapter for
details about when to use the accelerator while
you start your vehicle.
*
[ST04500(ALL)03/95]
Starting Your Vehicle
%*
[ST05000(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05100(ALL)05/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
*
[ST05200(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05300(ALL)01/95]
1. Make sure you and all your passengers
buckle your safety belts. SeeSafety Restraints
in the Index for more details.
*
[ST05400(ALL)03/95]
2. Make sure the headlamps and other
accessories are turned off when starting.
*
[ST05500(ALL)02/92]
3.If you have an automatic transaxle, make
sure that the gearshift is in P (Park) and the
parking brake is set before you turn the key.
*
[ST05600(ALL)07/93]
If you have a manual transaxle, make sure
that the parking brake is fully set, push the
clutch pedal to the floor, and put the
gearshift into Neutral before you turn the
key.(Remember, the starter will operate
only if the clutch pedal is pushed all the
way to the floor.)
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

44 %
*
[ST06460(ALL)05/95]
For a warm engine:
*
[ST06470(ALL)04/95]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[ST06480(ALL)05/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter or flood the engine.
*
[ST06490(ALL)05/95]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
*
[ST06500(ALL)05/95]
NOTE: Your vehicle is equipped with an
automatic transaxle that has an
interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
%*
[ST06510(ALL)04/95]
If the engine does not start after two attempts:
*
[ST06520(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST06530(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST06540(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST06550(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST06560(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST06570(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

46
*
[ST09200(ALL)05/95]
RWARNING
To prevent electrical shock, do not use
your heater with ungrounded electrical
systems or two-pronged (cheater) adapters.
*
[ST09300(ALL)03/95]
For best results, plug the heater in at least three
hours before you start your vehicle. Using the
heater for longer than three hours will not
damage the engine, so you can plug it in at
night to start your vehicle the following
morning.
%
*
[ST10000(ALL)03/95]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
*
[ST10005(ALL)04/95]
The Fuel Pump Shut-off Switch
[ST10010(ALL)01/95]
If the engine cranks but does not start or does
not start after a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device intended to stop the fuel
pump when your vehicle has been involved in a
substantial jolt.
*
[ST10015(ALL)03/95]
Once the shut-off switch is triggered, you must
reset the switch by hand before you can start
your vehicle.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

47 [ST10025(ALL)01/95]
three fourths page art:0030295-I
The location of the fuel pump shut-off switch
*
[ST10030(ALL)05/95]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

48
*
[ST10035(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[ST10040(ALL)02/95]
1. Turn the key in the ignition to the LOCK
position.
*
[ST10045(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST10050(ALL)01/95]
3. If you do not see or smell fuel, push the red
reset button on the fuel pump shut-off
switch down.
[ST10052(ALL)04/95]
The reset switch on your vehicle is located on
the left side of the luggage compartment
under the carpet. The red reset button is
under the raised area of the rubber cover.
*
[ST10055(ALL)02/95]
4. Attempt to start your vehicle. If the vehicle
starts, let it run a few seconds, then turn the
key to the LOCK position.
*
[ST10060(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
%*
[ST11700(ALL)05/95]
Guarding Against Exhaust Fumes
*
[ST11800(ALL)02/95]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
*
[ST11900(ALL)05/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

58 [LG04360(ALL)04/95]The Low Fuel Light
[LG04375(ALL)08/91]
This light comes on when fuel level in your tank
has reached approximately 2-3 gallons (7-10
liters).
[LG04395(ALL)01/92]
one inch art:0032048-A
Low fuel light
*
[LG04500(ALL)01/95]
High Beam Light
*
[LG04600(ALL)03/95]
This light comes on when the headlamps are
turned to high beam or when you flash the
lights.
*
[LG04700(ALL)01/92]
one inch art:0030174-A
High beam light
%*
[LG05300(ALL)03/95]
Check Engine Warning Light
*
[LG05400(ALL)05/95]
This light comes on when the electronic engine
control system is not working properly. This is
the computer system that controls the operating
conditions of the engine.
*
[LG05450(ALL)09/93]
one inch art:0030175-B
Check engine warning light
File:prlgp.ex
Update:Fri Jun 23 19:38:06 1995

60
*
[LG05890(ALL)10/93]
Gauges
*
[LG05900(ALL)01/95]
Fuel Gauge
*
[LG06000(ALL)01/95]
The fuel gauge displays approximately how
much fuel you have in the fuel tank.
*
[LG06025(ALL)05/93]
The ignition must be turned off while putting
fuel in the tank in order to get a correct fuel
gauge reading after the ignition is turned on.
*
[LG06075(ALL)05/93]
The fuel gauge indicator may vary slightly while
the vehicle is in motion. This is the result of fuel
movement within the tank. You can get a more
accurate reading with the vehicle on smooth,
level ground.
[LG06100(ALL)01/89]
Charging System Gauge
[LG06200(ALL)05/95]
This gauge tells you your battery's voltage when
you turn your ignition key to ON. When you
start your engine, the pointer should move to
the NORMAL range if you are not operating
any electrical accessories. (If electrical accessories
are operating and the engine is not running, the
pointer may move into the red area).
[LG06300(ALL)01/94]
If the pointer moves into the red area when no
electrical accessories are operating, have the
vehicle's electrical system checked.
*
[LG06310(ALL)05/94]
Engine Oil Pressure Gauge
[LG06330(ALL)05/95]
The gauge needle should stay in the NORMAL
range (indicating normal engine oil pressure). If
the needle drops below the NORMAL range into
the low range, there is a loss of oil pressure.
[LG06335(ALL)11/91]
If this happens:
*
[LG06340(ALL)01/95]
1. Pull off the road as soon as safely possible.
*
[LG06350(ALL)04/95]
2. Shut off the engine immediately or severe
engine damage could result.
File:prlgp.ex
Update:Fri Jun 23 19:38:06 1995

69
*
[IP06950(ALL)01/95]
Sometimes you may notice slight engine surging
if you have the air conditioner on. This is
normal, as the system is designed to cycle the
compressor on and off to maintain desired
cooling. The reduced compressor operation
should benefit fuel economy.
*
[IP07000(ALL)01/95]
On some vehicles with air conditioning,
wide-open throttle acceleration will temporarily
cut off the air conditioning.
*
[IP07050(ALL)01/95]
Since the air conditioner removes a lot of
moisture from the air during operation, it is
normal for water to drip on the pavement under
the air conditioner drain after you have stopped
the vehicle.
[IP07150(ALL)08/91]
Action for heating and windshield defrosting are
identical for cars equipped with either the
Heating Only Systemor theHeating and Air
Conditioning System. For instructions about these
functions, see the previous section,Heating Only
System. For instructions about using the air
conditioning, see the following sections.
[IP07350(ALL)01/95]
MAX A/C
[IP07360(ALL)01/95]
When MAX A/C is selected, cooled interior air
is recirculated through the system. This position
is more efficient than NORM A/C.
*
[IP07375(ALL)09/93]
To cool your vehicle quickly in warm weather:
[IP07400(ALL)08/91]
1. Turn the function selector control to MAX
A/C.
[IP07450(ALL)08/91]
2. Turn the temperature control to the blue
(cool) area.
[IP07475(ALL)08/91]
3. Set the fan at the desired speed.
*
[IP07500(ALL)09/93]
If the inside of your vehicle is very warm,
drive for a few minutes with the windows
down. This forces most of the hot, stale air
out of the vehicle and helps the air
conditioning cool the vehicle faster.
File:pripp.ex
Update:Fri Jun 23 19:37:35 1995

70 [IP07550(ALL)01/95]Because MAX A/C uses recirculated air, MAX is
usually more efficient than NORM A/C. You
can switch to outside air (NORM A/C) at any
time, especially after the vehicle has cooled
down.
[IP07560(ALL)11/91]
You will notice a slight odor when using the
MAX A/C position. This is normal. If the odor
becomes annoying, switch the function selector
to NORM A/C.
[IP07575(ALL)08/91]
To provide the most quiet operation when using
MAX A/C, reduce the fan speed after a
comfortable temperature has been reached.
[IP07800(ALL)04/95]
NORM A/C
[IP08025(ALL)01/94]
When maximum air conditioning is not needed,
you can use the NORM A/C position to cool
your vehicle with outside air. Cooling your
vehicle this way brings in outside air and is
quieter, but it is less efficient.
[IP08050(ALL)05/95]
To cool your vehicle using outside air:
[IP08075(ALL)08/91]
1. Turn the function selector control to NORM
A/C.
[IP08150(ALL)08/91]
2. Turn the temperature control all the way to
left to the blue (cool) area.
*
[IP08175(ALL)10/93]
3. Set the fan at the desired speed.
[IP08400(ALL)01/95]
In mild weather, setting the function selector
control in the VENT position will add cool air to
your vehicle without using the air conditioning.
You will get better fuel economy without using
the air conditioning.
File:pripp.ex
Update:Fri Jun 23 19:37:35 1995