ignition FORD PROBE 1996 2.G Owners Manual

22 %
*
[SR15127(ALL)05/95]
The air bag system uses a readiness light on the
instrument cluster and a tone to indicate the
condition of the system. When you turn the
ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and
then turn off. This indicates that the system is
operating normally. NOTE: Maintenance of the
air bag system is not required.
%*
[SR15129(ALL)05/95]
A problem with the system is indicated by one
or more of the following:
*
[SR15131(ALL)05/95]
q
the readiness light will either flash or stay lit,
*
[SR15133(ALL)05/95]
q
or it will not light immediately after ignition
is turned on,
*
[SR15135(ALL)05/95]
q
or a group of five beeps will be heard. The
tone pattern will repeat periodically until the
problem and light are repaired.
*
[SR15139(ALL)05/95]
If any of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately. Unless serviced, the air bag
supplemental restraint system may not function
properly in the event of a collision.
*
[SR15145(ALL)05/95]
RWARNING
Do not attempt to service, repair, or
modify the Air Bag Supplemental
Restraint System or its fuses. See your
Ford or Lincoln-Mercury dealer.
%*
[SR15150(ALL)05/95]
Disposal of air bags or air bag equipped
vehicles
*
[SR15160(ALL)05/95]
For disposal of air bags or air bag equipped
vehicles, see your local Ford or Lincoln-Mercury
dealer. Air bagsMUSTbe disposed of by
qualified personnel.
File:prsrp.ex
Update:Fri Jun 23 19:39:12 1995

37
Starting Your Probe
*
[ST01700(ALL)03/95]
Ignition
*
[ST01800(ALL)01/95]
Understanding the Positions of the Ignition
[ST02050(ALL)01/92]
one third page art:0032054-A
Ignition lock cylinder
*
[ST02100(ALL)09/93]
LOCK locks the steering wheel. It also locks the
gearshift lever in P (Park) (automatic transaxle).
*
[ST02200(ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
[ST02250(ALL)08/91]
To remove the key if you have a manual
transaxle, push the key in while turning it to the
LOCK position.
*
[ST02300(ALL)05/95]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
[ST02350(ALL)01/94]
ACC (Accessory) allows some of your vehicle's
electrical accessories to operate while the engine
is not running.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

38
*
[ST02400(ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST02500(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
*
[ST02505(ALL)09/93]
Shift-lock System
*
[ST02510(ALL)09/93]
For your safety, the optional automatic transaxle
has the shift-lock system, which prevents shifting
the transaxle out of the P (Park) position without
depressing the brake pedal when the ignition
switch is in the ON position.
*
[ST02515(ALL)07/89]
To shift the transaxle out of the P (Park)
position:
*
[ST02521(ALL)05/90]
1. Depress and hold the brake pedal.
*
[ST02526(ALL)11/93]
2. Start the engine.
[ST02528(ALL)01/94]
3. Push in the thumb button and move the
shift selector lever.
[ST02530(ALL)06/93]
4. SeeShift Lock Emergency Overridein this
section for more information.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

39 [ST02532(ALL)06/93]
two third page art:0032064-D
Automatic console-mounted gearshift lever
*
[ST02535(ALL)09/93]
NOTE: When the ignition key is in the ACC
or LOCK position, the transaxle cannot
be shifted from the P (Park) position.
If the brake pedal is repeatedly
depressed and released when the
ignition is in the ON position and the
selector lever is in the P (Park)
position, a chattering near the gearshift
lever may be heard. This is not a
malfunction.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

40
*
[ST02538(ALL)03/94]
NOTE: Your vehicle's gearshift lever is
securely latched in P (Park) if you
cannot move it without pushing in the
thumb button. Keep the brake pedal
depressed while moving your gearshift
lever.
*
[ST02540(ALL)09/93]
To make the system more effective, the ignition
key cannot be removed unless the gearshift
selector lever is in the P (Park) position.
[ST02545(ALL)06/93]
Shift lock emergency override
[ST02550(ALL)01/94]
If the gearshift selector lever should fail to move
from the P (Park) position with the brake pedal
depressed, continue depressing the brake pedal.
[ST02557(ALL)06/93]
1. Remove the shift lock override cover with a
screwdriver.
[ST02563(ALL)06/93]
2. Insert the screwdriver into the shift lock
override opening and push the screwdriver
handle down.
*
[ST02570(ALL)06/93]
3. Push and hold the thumb button.
[ST02600(ALL)01/94]
4. Move the shift selector lever.
*
[ST02690(ALL)06/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Probein
this Owner Guide for instructions on checking
and replacing fuses.
*
[ST02700(ALL)05/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

41 %
*
[ST02900(ALL)02/95]
Removing the Key From the Ignition
*
[ST03000(ALL)09/93]
1. Put the gearshift selector lever in P (Park)
(automatic transaxle) or 1 (First) (manual
transaxle).
*
[ST03100(ALL)01/95]
2. Set the parking brake fully.
[ST03400(ALL)01/94]
3.For a manual transaxle:Push in on the lock
cylinder and turn the key from ACC to
LOCK.
[ST03425(ALL)01/94]
For an automatic transaxle:Turn the key to
LOCK.
*
[ST03500(ALL)03/95]
4. Remove the key.
*
[ST03600(ALL)10/90]
If the driver or passenger door is open while the
key is still in the ignition, a warning chime
sounds.
*
[ST03700(ALL)05/95]
RWARNING
Always set the parking brake fully and
make sure that the gearshift is securely
latched in P (Park) (automatic transaxle) or
in 1 (First) (manual transaxle).
*
[ST03900(ALL)01/93]
RWARNING
Do not leave children, unreliable adults,
or pets alone in your vehicle. They could
accidentally injure themselves or others
through inadvertent operation of the
vehicle. Further, on hot, sunny days,
temperatures in a closed vehicle could
quickly become high enough to cause
severe and possibly fatal injuries to
people as well as animals.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

43
*
[ST05700(ALL)03/95]
Testing the Warning Lights
*
[ST05800(ALL)03/95]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to theWarning
Lights and Gaugeschapter.
*
[ST06000(ALL)02/95]
Starting Your Engine
*
[ST06100(ALL)02/95]
To start your engine:
*
[ST06300(ALL)05/95]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[ST06320(ALL)03/95]
2. Keep your foot on the brake pedal and turn
the ignition key to the ON position.
*
[ST06330(ALL)03/95]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
*
[ST06340(ALL)02/95]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[ST06400(ALL)02/95]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
%*
[ST06430(ALL)04/95]
For a cold engine:
*
[ST06440(ALL)05/95]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[ST06450(ALL)04/95]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

44 %
*
[ST06460(ALL)05/95]
For a warm engine:
*
[ST06470(ALL)04/95]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[ST06480(ALL)05/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter or flood the engine.
*
[ST06490(ALL)05/95]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
*
[ST06500(ALL)05/95]
NOTE: Your vehicle is equipped with an
automatic transaxle that has an
interlock that prevents you from
shifting out of P (Park) unless your
foot is on the brake pedal.
%*
[ST06510(ALL)04/95]
If the engine does not start after two attempts:
*
[ST06520(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST06530(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST06540(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST06550(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST06560(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST06570(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

48
*
[ST10035(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[ST10040(ALL)02/95]
1. Turn the key in the ignition to the LOCK
position.
*
[ST10045(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST10050(ALL)01/95]
3. If you do not see or smell fuel, push the red
reset button on the fuel pump shut-off
switch down.
[ST10052(ALL)04/95]
The reset switch on your vehicle is located on
the left side of the luggage compartment
under the carpet. The red reset button is
under the raised area of the rubber cover.
*
[ST10055(ALL)02/95]
4. Attempt to start your vehicle. If the vehicle
starts, let it run a few seconds, then turn the
key to the LOCK position.
*
[ST10060(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
%*
[ST11700(ALL)05/95]
Guarding Against Exhaust Fumes
*
[ST11800(ALL)02/95]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
*
[ST11900(ALL)05/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
File:prstp.ex
Update:Fri Jun 23 19:38:23 1995

54 [LG01775(ALL)04/93]The mechanical cluster on the Probe GT model is
similar to the one shown. The two exceptions
are: the speedometer on the GT model shows
140 mph (225 km/h) and it has a 7,000 rpm
red-line tachometer.
[LG01780(ALL)01/92]
one third page art:0032087-B
GT model speedometer and tachometer
[LG01800(ALL)01/94]
The following warning lights and gauges are on
the cluster. All of the warning lights and gauges
alert you to possible problems with your vehicle.
The following sections detail what each of these
indicators means.
*
[LG01950(ALL)01/95]
Indicator Lights and Chimes
%*
[LG01975(ALL)05/95]
Safety Belt Warning Light and Chime
[LG01980(ALL)03/94]
This warning light and chime remind you to
fasten your safety belt. If you do not fasten your
safety belt before the ignition is turned to ON,
the chime will sound for 4 to 8 seconds and the
warning light will illuminate for 1 to 2 minutes,
or until the safety belt is fastened. If you fasten
the safety belt before the ignition is turned to
ON, neither the light nor chime will activate.
File:prlgp.ex
Update:Fri Jun 23 19:38:06 1995