lock FORD PROBE 1997 2.G Service Manual

174 [ER09990(ALL)04/96]Your vehicle has metric (12 mm) wheel studs
and lug nuts. During wheel removal and
replacement, make certain that you use the same
lug nuts to reinstall the wheel or replace them
with nuts of the same metric size and threading.
*
[ER10000(ALL)01/96]
RWARNING
Installation of an English thread nut on a
metric stud (or vice-versa) will not
properly secure the wheel to the hub.
Damaged studs may result in wheel
separation and possible injury.
*
[ER10200(ALL)03/96]
5. Lower the vehicle by turning the jack handle
counterclockwise.
[ER10300(ALL)01/96]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the illustration
under step 2.
[ER10700(ALL)01/96]
7. Put the tire, jack, and wrench away.
[ER10750(ALL)01/96]
8. Unblock the wheels.
%
*
[ER11000(ALL)02/96]
Jump-Starting Your Vehicle
[ER11100(ALL)01/96]
Your vehicle has a Motorcraft maintenance-free
battery. Your vehicle's battery may die if you
leave the lights on or any electrical equipment
on after you turn the engine off. If this happens,
you may be able to jump-start from a booster
battery to start your vehicle.
*
[ER11150(ALL)02/96]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
File:10prerp.ex
Update:Thu Jun 13 09:57:39 1996

181 [ER16300(ALL)01/96]
two third page art:0032195-A
*
[ER16400(ALL)01/96]
Do not use your vehicle's steering column lock
to secure the wheels in a straight-ahead position.
Always use a steering wheel clamping device
designed for towing service.
*
[ER16500(ALL)01/96]
Refer toTowing behind another vehicle
Ðrecreational vehiclein the Index for information
on towing behind an RV.
File:10prerp.ex
Update:Thu Jun 13 09:57:39 1996

185
*
[MC02000(ALL)01/96]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[MC02100(ALL)01/96]
q
Never get under a vehicle while it is
supported only by a jack. If you must work
under a vehicle, use safety stands.
*
[MC02200(ALL)01/96]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[MC02500(ALL)01/96]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[MC02700(ALL)01/96]
Working with the engine off:
*
[MC02750(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[MC02800(ALL)01/96]
2. Remove the key from the ignition after you
turn the engine off.
*
[MC02850(ALL)01/96]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC02900(ALL)01/96]
Working with the engine on:
*
[MC03000(ALL)01/96]
1. Set the parking brake fully and make sure
the gearshift is securely latched in P (Park)
(automatic transaxle) or Neutral (manual
transaxle).
*
[MC03100(ALL)01/96]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[MC03200(ALL)01/96]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove it
while the engine is running.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

197 [MC10660(ALL)05/96]
one inch art:0032038-B
*
[MC10680(ALL)05/96]
Check the coolant level in the coolant recovery
reservoir the next few times you drive the
vehicle. If necessary, add enough of a 50/50
mixture of coolant and water to bring the liquid
level to the fill line on the reservoir.
[MC10700(ALL)05/96]
RWARNING
Never remove the coolant recovery cap
while the engine is running or hot.
*
[MC10720(ALL)05/96]
If you must remove the coolant recovery cap,
follow these steps to avoid personal injury
caused by escaping steam or engine coolant:
*
[MC10740(ALL)05/96]
1. Before you remove the cap, turn the engine
off and let it cool.
*
[MC10760(ALL)05/96]
2. When the engine is cool, wrap a thick cloth
around the cap and turn it slowly,
counterclockwise to the first stop.
*
[MC10780(ALL)05/96]
3. Step back while the pressure releases.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

198
*
[MC10800(ALL)05/96]
4. When you are sure that all the pressure has
been released, use the cloth to press the cap
down, turn it counterclockwise, and remove
it.
[MC10820(ALL)05/96]
Use Ford Premium Engine Coolant
E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B)
or an equivalent premium engine coolant that
meets Ford specification ESE-M97B44-A. Ford
Premium Engine Coolant is an optimized
formula that will protect all metals and rubber
elastomers used in Ford cooling systems for 4
years or 50,000 miles (80,000 km).
[MC10840(ALL)05/96]
Do not use alcohol or methanol antifreeze or any
engine coolants mixed with alcohol or methanol
antifreeze. Do not use supplemental coolant
additives in your vehicle. These additives may
harm your engine cooling system.The use of an
improper coolant may void the warranty of
your vehicle's engine cooling system.
[MC10860(ALL)05/96]
Recycled engine coolant
*
[MC10880(ALL)05/96]
Ford Motor Company recommends that Ford
and Lincoln-Mercury dealers use recycled engine
coolant produced by Ford-approved processes.
Not all coolant recycling processes produce
coolant which meets Ford specification
ESE-M97B44-A, and use of such coolant may
harm engine and cooling system components.
*
[MC10900(ALL)05/96]
Always dispose of used automotive fluids in a
responsible manner. Follow your community's
regulations and standards for recycling and
disposing of automotive fluids.
[MC10920(ALL)05/96]
Coolant refill capacity
[MC10940(ALL)05/96]
To find out how much fluid your vehicle's
cooling system can hold, seeRefill capacitiesin
theCapacities and Specificationschapter.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

207
*
[MC24400(ALL)02/96]
Wiper blade replacement
*
[MC24500(ALL)01/96]
If the wipers still do not work properly after
you clean them, you may need to replace the
wiper blade assembly. When replacing the wiper
blade assembly always use a Motorcraft part or
equivalent.
*
[MC24525(ALL)08/95]
To replace the wiper blades:
*
[MC24535(ALL)01/96]
1. Pull the wiper arm away from the
windshield and into the lock position.
*
[MC24550(ALL)01/96]
2. Turn the blade at an angle from the wiper
arm. Push the lock pin with a screwdriver to
release the blade and pull the wiper blade
down toward the windshield to remove it
from the arm.
*
[MC24560(ALL)08/95]
3. Attach a new wiper blade to the wiper arm
and press it into place until you hear it click.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

209
*
[MC25100(ALL)03/96]
q
Make sure the weight of your load is evenly
distributed.
*
[MC25200(ALL)03/96]
q
Adjust tire pressure to recommended
specifications found on the Safety Compliance
Certification Label.
*
[MC25300(ALL)03/96]
If you do not take these precautions, your tires
may fail or go flat.
*
[MC25390(ALL)03/96]
Ford Motor Company recommends obeying
posted speed limits.
*
[MC25400(ALL)03/96]
RWARNING
Driving too fast for conditions creates the
possibility of loss of vehicle control.
Driving at very high speeds for extended
periods of time may result in damage to
vehicle components.
[MC25600(ALL)01/96]
At least once a month, check the pressure in all
your vehicle's tires, including the spare. Use an
accurate tire pressure gauge. Check the tire
pressure when tires are cold, that is, after the
vehicle has been parked for at least one hour or
has been driven less than 3 miles (5 km).
[MC25700(ALL)01/96]
You can find your vehicle's proper tire inflation
pressure on the tire decal on the right door lock
pillar.
*
[MC25850(ALL)01/96]
RWARNING
Improperly inflated tires can affect vehicle
handling and can fail suddenly, possibly
resulting in loss of vehicle control.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

216 [MC30400(ALL)01/96]
half page art:0032107-CManual fuel filler-lid override (behind left rear trim panel
in hatch)
[MC30500(ALL)01/96]
To fill the fuel tank:
*
[MC30600(ALL)01/96]
1. After opening the fuel filler door, remove
the cap carefully and slowly by turning it
counterclockwise 1/2 to 3/4 turn.
*
[MC30700(ALL)01/96]
RWARNING
The fuel system may be under pressure. If
the fuel cap is venting vapor or if you
hear a hissing sound, wait until it stops
before completely removing the cap.
*
[MC30800(ALL)01/96]
2. Put the nozzle all the way inside the fuel
filler pipe before pumping the fuel.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

217
*
[MC30900(ALL)01/96]
NOTE: If you spill any fuel on the body of
your vehicle, clean it off immediately.
The fuel may dull or soften the paint
if you do not wash it off.
%*
[MC31000(ALL)03/96]
3. Replace the fuel cap completely when you
are finished. Turn it clockwise 1/4 turn until
it is tight. It will click when it is fully
tightened.
*
[MC31100(ALL)01/96]
4. Push the fuel door closed.
*
[MC31200(ALL)01/96]
If you lose the fuel cap, replace it with an
authorized Motorcraft or equivalent part.
%*
[MC31300(ALL)01/96]
RWARNING
If you do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly
in a collision.
*
[MC31400(ALL)01/96]
NOTE: If you replace your fuel cap with an
aftermarket fuel filler cap, the customer
warranty may be void for any damage
to the fuel tank and/or fuel system.
%*
[MC31500(ALL)01/96]
Choosing the Right Fuel
*
[MC31600(ALL)05/96]
Use only UNLEADED FUEL. The use of leaded
fuel is prohibited by law and could damage
your vehicle. The damage may not be covered
by your warranty.
*
[MC31700(ALL)05/96]
Your vehicle was not designed to use fuel
containing manganese-based additives such as
MMT. Additionally, vehicles certified to
California emission standards (indicated on the
underhood Vehicle Emissions Control
Information label) are designed to operate on
California reformulated gasolines. If California
reformulated gasoline is not available when you
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996

226 %
*
[MC43100(ALL)01/96]
The alignment of your headlamps should be
checked if:
*
[MC43200(ALL)01/96]
q
oncoming motorists frequently signal you to
turn off your vehicle's high beams when you
do not have the high beams on
*
[MC43300(ALL)01/96]
q
the headlamps do not seem to give you
enough light to see clearly at night
*
[MC43400(ALL)01/96]
q
the headlamp beams are pointed substantially
away from a position slightly down and to
the right
%*
[MC43500(ALL)01/96]
Headlamp Bulb
[MC43600(ALL)01/96]
Your vehicle has retractable halogen headlamps.
If you need to replace a headlamp, have it done
by a Ford service technician.
% [MC43700(ALL)04/96]
High-Mount Brakelamp Bulb
[MC43800(ALL)01/96]
To replace the bulb:
[MC43900(ALL)01/96]
1. Remove the two side trim liftgate panels.
[MC44000(ALL)01/96]
2. Remove the liftgate trim clip and the liftgate
trim.
[MC44100(ALL)01/96]
3. Remove the bulb from the socket by pushing
it in and turning it counterclockwise.
[MC44200(ALL)01/96]
4. Install the bulb by pushing straight into the
lamp socket and turning it clockwise until it
locks in place.
[MC44300(ALL)01/96]
5. Replace the liftgate trim and trim clip.
[MC44400(ALL)01/96]
6. Replace the two side trim liftgate panels.
File:11prmcp.ex
Update:Thu May 16 12:08:53 1996