brakes FORD RANGER 1996 2.G Owners Manual

Introductory Information
5
%*
[IN06000(ALL)01/95]
Breaking Your Vehicle In
*
[IN06100(ALL)03/95]
Your new vehicle goes through an adjustment or break-in
period during the first 1,000 miles (1,600 km) that you drive it.
During the break-in period, you need to pay careful attention to
how you drive your vehicle.
%*
[IN06300(ALL)01/95]
n
Avoid sudden stops.Because your vehicle has new brake
linings, you should take these steps:
*
[IN06400(ALL)01/95]
Ð Watch traffic carefully so that you can anticipate when to
stop.
*
[IN06500(ALL)01/95]
Ð Begin braking well in advance.
*
[IN06600(ALL)01/95]
Ð Apply the brakes gradually.
*
[IN06700(ALL)01/95]
The break-in period for new brake linings lasts for 100 miles
(160 km) of city driving or 1,000 miles (1,600 km) of
highway driving.
*
[IN06750(ALL)12/93]
n
Wheel lug nuts must be retightened to proper torque
specifications at 500 miles/800 km of new vehicle operation.
Proper torque specifications are provided in this guide. Also
retighten to proper torque specification at 500 miles/800 km
after any wheel change or any other time the wheel lug nuts
have been loosened.
%*
[IN06800(ALL)01/95]
n
Use only the type of engine oil that Ford recommends.See
Engine oil recommendationsin the Index. Do not use special
ªbreak-inº oils.
*
[IN07000(ALL)03/95]
Some vehicles are equipped with a Powertrain Control Module
that limits engine speeds with a cut-out mode to promote
durability.
File:02uninr.ex
Update:Wed May 1 13:42:39 1996

56
%*
[LG03000(ALL)06/94]
The Mechanical Cluster
*
[LG03100(ALL)06/93]
The following warning lights and gauges are on the mechanical
cluster. All of the warning lights and gauges alert you to
possible problems with your vehicle. Some of the lights listed
are optional. The following sections detail what each of these
indicators means.
%*
[LG03200(ALL)06/95]
Brake System Warning Light
*
[LG03300(ALL)03/95]
The warning light for the brakes can show two things Ð that
the parking brake is not fully released, or that the brake fluid
level is low in the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by your dealer or a
qualified service technician.
*
[LG03400(ALL)05/94]
This light comes on when you turn the ignition key to START
to verify that the indicator bulb is working. If the light stays on
or comes on after you have released the parking brake fully,
have the hydraulic brake system serviced.
*
[LG03500(ALL)05/95]
RWARNING
The BRAKE light indicates that the brakes may not be
working properly. Have the brakes checked immediately.
[LG03600(ALL)04/94]
6 pica art:0021145-A
Brake warning light symbols
File:05unlgr.ex
Update:Wed May 1 13:45:37 1996

Driving Your Ranger
165
*
[DR15100(ALL)03/95]
When you slow down or climb a steep hill, always downshift
before the engine starts to lose power. Downshifting reduces the
chance of stalling and gives your vehicle better acceleration to
increase speed again.
*
[DR15200(ALL)03/95]
When you drive down steep hills, downshifting helps you keep
a safe speed and helps prevent unnecessary wear on the brakes.
*
[DR15300(ALL)03/95]
When you come to a stop, do not downshift through each gear.
Disengage the clutch and use the brake as necessary.
Downshifting through the gears decreases your vehicle's fuel
economy.
*
[DR15400(ALL)05/95]
RWARNING
Continued use of a damaged or worn clutch, prolonged
clutch slippage or downshifting at excessive speeds can
result in a failure of the engine, transmission or clutch
components.
*
[DR15500(ALL)03/91]
Transmission Function
[DR15600(ALL)10/94]
Upshift at the speeds specified in the chart. All forward gears
are synchronized allowing you to shift into them with your
vehicle in motion. The clutch pedal should be fully depressed
when shifting.
*
[DR15625(ALL)04/94]
NOTE: Shifting during extremely low rpm's can result in a
momentary audible rattle which disappears as vehicle
rpm's are increased. Shifting at higher speeds will
eliminate this sound.
*
[DR15700(ALL)03/95]
Parking
*
[DR15800(ALL)01/95]
To park your vehicle, apply the service brake pedal, and shift
into N (Neutral) while still maintaining pressure on the service
brake. Set the parking brake fully. Shift into first and turn off
the ignition.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
175
*
[DR19700(R )08/94]
n
Manual locking hubs must be in LOCK position before
shifting into four-wheel drive.
*
[DR19800(ALL)11/89]
When using four-wheel drive, maintain steering wheel control at
all times, especially in rough terrain. Since sudden changes in
terrain can result in abrupt steering wheel motion, make sure
you grip the steering wheel rim from the outside. Do not grip
the spokes.
*
[DR19900(ALL)05/90]
Drive cautiously to avoid vehicle damage from concealed objects
such as rocks and stumps. Know the terrain or examine maps of
the area in question before driving. Map out your route
beforehand. To maintain steering and braking control of your
vehicle, you must have all four tires on the ground, and they
must be rolling, not sliding or spinning.
[DR19925(ALL)10/94]
Transmission upshift in 4WD with transfer case in 4WD LOW
may be quite firm due to large total gear reduction. This
condition is normal.
*
[DR20000(ALL)11/89]
Sand
*
[DR20100(ALL)11/89]
When driving over sand, try to keep all four wheels of the
vehicle on the most solid area of the trail. Do not reduce the
tire pressures but shift to a lower gear and drive steadily
through the terrain. Apply accelerator slowly and avoid
spinning the wheels.
*
[DR20200(ALL)11/89]
Mud and Water
*
[DR20300(ALL)12/89]
When driving through water, determine the depth; avoid water
higher than the bottom of the hubs (if possible) and proceed
slowly. If the ignition system gets wet, the vehicle may stall.
*
[DR20400(ALL)11/89]
Once through water, always try the brakes. Wet brakes do not
stop the vehicle as effectively as dry brakes. Drying can be
improved by moving your vehicle slowly, while applying light
pressure on the brake pedal.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
177
*
[DR21310(ALL)05/95]
All utility-type and Four-Wheel Drive vehicles have special
design and equipment features to make them capable of
performing in a wide variety of off-road applications. Specific
design characteristics give them higher centers of gravity than
ordinary passenger cars.
*
[DR21325(ALL)08/95]
RWARNING
Utility and four-wheel drive vehicles are NOT designed
for cornering at speeds as high as passenger cars any
more than low-slung sports cars are designed to perform
satisfactorily under off-road conditions. Avoid sharp
turns or abrupt maneuvers in these vehicles.
%*
[DR21400(ALL)03/95]
Brakes
*
[DR21500(ALL)01/93]
Front Disc Brakes
*
[DR21600(ALL)06/95]
The front disc brakes are self-adjusting. They do not require
service other than periodic inspection for pad wear.
*
[DR21900(R )10/94]
Rear Drum Brakes
*
[DR22000(R )08/95]
The rear drum brakes are self-adjusting. Automatic adjustment
occurs when the brakes are applied while ªbacking up.º If
normal operation does not include much backing, adjust the
brakes when they seem ªlow,º using the procedure underIf
Brakes Do Not Grip Well or Pedal is ªLowºin this chapter.
*
[DR22100(ALL)11/89]
Hydraulic Power Brakes
[DR22200(ALL)08/94]
The hydraulic brake system is made up of two independent
hydraulic circuits. One hydraulic circuit supplies fluid to the
front disc brakes and the other hydraulic circuit supplies fluid
to the rear drum or disc brakes. These two circuits are supplied
by a common hydraulic brake fluid reservoir, with a fluid level
sensor.
*
[DR22300(ALL)11/89]
The brake light in the instrument cluster will light for low brake
fluid in the common brake fluid reservoir.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

178
*
[DR22400(ALL)05/95]
RWARNING
An increase in pedal travel will result in reduced braking
capability. The brake system should be checked
immediately.
%*
[DR22500(R )10/94]
Rear Anti-lock Brakes
*
[DR22750(R )10/94]
Your vehicle may be equipped with a Rear Anti-lock Brake
System. This system prevents at least one and often both rear
wheels from completely locking up when the brakes are applied
in a panic stop, for example.
*
[DR22800(R )07/94]
Even with the Anti-lock Brake System, you should be careful
when braking. Front brake lock up on any surface, even on
smooth pavement causes loss of steering control. Heavy braking
on roads with loose surfaces such as snow or gravel, or severe
pavement irregularities could also cause you to lose steering
control of your vehicle.
*
[DR22900(R )05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[DR22901(R )10/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
179
[DR22905(ALL)10/94]
Four Wheel Anti-lock Brake System
*
[DR22912(R )08/94]
Your vehicle may be equipped with a Four Wheel Anti-lock
Braking System (4WABS). The 4WABS helps the driver to
maintain vehicle control by preventing wheel lockup during
hard braking.
*
[DR22915(ALL)03/94]
The 4WABS operates with a computer that is able to optimize
vehicle control during braking on varying tire and road
conditions by modulating the brake pressure at each of the front
wheels and the rear axle. This ªpumping actionº is similar to
the driver ªpumpingº the brakes but happens at a much faster
rate.
*
[DR22920(ALL)05/95]
RWARNING
The Anti-lock system does NOT assist the vehicle in
stopping quickly on wet or icy surfaces. Heavy braking
combined with poor road conditions could cause you to
lose steering control of your vehicle.
*
[DR22925(ALL)10/94]
Using anti-lock brakes
*
[DR22930(ALL)05/94]
The operation of a vehicle with 4WABS is not similar to the
operation of normal brakes. Some differences exist and are listed
below:
*
[DR22935(ALL)10/94]
n
Apply the brake steadily. In the event of a panic stop, do
NOT ªpumpº the brakes. ªPumpingº the brakes during an
Anti-lock stop will diminish braking effectiveness.
%*
[DR22940(ALL)10/94]
n
During an Anti-lock stop, the driver will notice a brake
pedal pulsation and hear some noise from the engine
compartment. This is an indication that the 4WABS system is
working correctly and is normal.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

180
*
[DR22945(ALL)05/95]
RWARNING
The Anti-lock system does NOT decrease the time
necessary to apply the brakes. Always leave enough room
between the vehicle in front of you and your vehicle.
*
[DR22950(ALL)05/95]
4WABS driver warning light
[DR22955(ALL)10/94]
The 4WABS computer continuously monitors the system while
driving for any electrical faults or system malfunctions. In
addition, the 4WABS computer performs an initial system check
called bulb proveout when the vehicle ignition is switched on.
During bulb proveout, the ABS light on the instrument cluster
will momentarily illuminate and then go out.
*
[DR22960(ALL)09/95]
NOTE: After starting the vehicle and upon initial drive-off,
the driver may notice a single pulse of the brake
pedal and a noise from the engine compartment. This
is part of the initial system check and is normal.
[DR22965(ALL)05/95]
Should a malfunction in the 4WABS system occur, the ABS light
on the instrument cluster will come on and stay on indicating
that the anti-lock system has been shut down and the vehicle
needs to be serviced. Normal braking is not affected unless the
brake warning light is also illuminated.
*
[DR22970(ALL)09/95]
NOTE: It is important to note that when the ABS Warning
Light is illuminated the ABS system is disabled. The
vehicle must be serviced immediately to restore the
benefits of the Anti-lock system.
*
[DR22975(ALL)09/95]
NOTE: Mobile phones or radio transmitters not installed by
Ford Motor Company may interfere with the Anti-lock
System. Should the Anti-lock system activate
unexpectedly or the Anti-lock Warning Light
illuminate after installation of such a unit, have the
installation of the unit checked.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

Driving Your Ranger
181
%*
[DR23000(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is ªLowº
%*
[DR23200(R )07/95]
If brakes do not grip well, it may indicate the rear drum brakes
need adjustment. To do this, drive the vehicle in reverse at
5 mph (8 km/h) on level, dry pavement. Stop the vehicle by
firmly applying the brakes. Repeat this procedure four or five
times.
*
[DR23250(ALL)11/89]
If during normal operation the brake pedal seems ªlowº, it may
indicate the need for a brake system inspection and/or service.
You should have your brakes checked as soon as possible.
%*
[DR23300(ALL)10/95]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified service technician.
*
[DR23400(ALL)11/89]
RWARNING
Modifications to the suspension spring rates and/or
vehicle ride height may adversely affect vehicle stopping
ability.
*
[DR23500(ALL)07/92]
If Brakes Pull
*
[DR23600(ALL)05/95]
n
Check tire pressure.
*
[DR23700(R )07/95]
n
Perform the self-adjustment procedure described underIf
Brakes Do Not Grip Well or Pedal is ªLow.º
*
[DR23800(ALL)05/95]
If pull occurs during the first 500 miles (800 km), make 10
moderately fast stops from 40 mph (65 km/h) and then
perform the self-adjustment procedure above. It may be
necessary to repeat this operation to properly seat new brake
linings and pads.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

182
%*
[DR24000(ALL)01/93]
Stopping Distances
*
[DR24100(ALL)11/89]
Stopping distances vary with different loads and driving
conditions. Use caution when encountering new conditions and
acquaint yourself with vehicle performance. Take full advantage
of engine braking power when slowing down.
%*
[DR24200(ALL)01/95]
Applying the Brakes
*
[DR24300(ALL)05/95]
Apply the brake pedal gradually. Use the ªsqueezeº technique
Ð push on the brake pedal with a steadily increasing force. This
allows the wheels to continue to roll while you are slowing
down, which lets you steer properly.
*
[DR24400(ALL)07/95]
Do not drive with your foot resting on the brake pedal. This
will increase your vehicle's stopping distance and may also
cause brake damage.
*
[DR24500(ALL)05/95]
RWARNING
If you are driving down a long or steep hill, shift to a
lower gear. Do not apply your brakes continuously, as
they may overheat and become less effective.
%*
[DR24600(ALL)03/95]
Using the Parking Brake
*
[DR24650(ALL)01/95]
The parking brake should be used whenever you park your
vehicle.
*
[DR24800(ALL)12/91]
The parking brake pedal is suspended just below the bottom of
the instrument panel to the left of service brake and/or clutch
pedals. To set the parking brake while parking your vehicle,
press the brake pedal with your right foot and hold it while
you push the parking brake pedal down firmly and fully with
your left foot.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996