parking brake FORD RANGER 1997 2.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1997, Model line: RANGER, Model: FORD RANGER 1997 2.GPages: 361, PDF Size: 3.39 MB
Page 13 of 361
10
%*
[IS03000(R)01/96]
The Mechanical Cluster
*
[IS03100(R)01/96]
The following warning lights and gauges are on the mechanical
cluster. All of the warning lights and gauges alert you to
possible problems with your vehicle. Some of the lights listed
are optional. The following sections detail what each of these
indicators means.
%*
[IS03200(R)01/96]
Brake System Warning Light
*
[IS03300(R)03/96]
The warning light for the brakes can show two things Ð that
the parking brake is not fully released, or that the brake fluid
level is low in the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by your dealer or a
qualified service technician.
*
[IS03400(R)03/96]
This light illuminates when you turn the ignition key to START
to verify that the indicator bulb is working. If the light stays on
or illuminates after you have released the parking brake fully,
have the hydraulic brake system serviced.
*
[IS03500(R)03/96]
RWARNING
The BRAKE light indicates that the brakes may not be
working properly. Have the brakes checked immediately.
[IS03600(R)01/96]
6 pica art:0021145-A
Brake warning light symbols
File:03unisr.ex
Update:Thu Mar 20 09:21:14 1997
Page 66 of 361
Controls and Features
63
[CF00290(R)03/96]
7-1/2 pica art:0090191-A
Fog lamp switch
*
[CF00300(R)03/96]
The fog lamps act as a supplement to the low beam headlamps
under limited visibility conditions such as rain, snow, dust or
fog and operate only when the low beam headlamps are on.
*
[CF00305(R)03/96]
To maximize fog lamp bulb life, it is recommended that the fog
lamp switch be turned off after each use prior to turning off the
headlamps.
%*
[CF00310(R)03/96]
Daytime Running Light System
*
[CF00315(R)03/96]
(Canadian vehicles only)
*
[CF00320(R)03/96]
The Daytime Running Light (DRL) system turns the high beam
headlamps on, with a reduced light output, when:
*
[CF00325(R)03/96]
n
The headlamp system is in the OFF position, and
*
[CF00330(R)03/96]
n
The vehicle has a fully released parking brake.
[CF00333(R)05/96]
n
The vehicle is running.
*
[CF00335(R)03/96]
The high beam indicator light on the instrument cluster will not
be on.
*
[CF00340(R)03/96]
RWARNING
The Daytime Running Light (DRL) system will not
illuminate the tail lamps and parking lamps. Turn on
your headlamps at dusk. Failure to do so may result in a
collision.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 77 of 361
74
*
[CF20450(R)01/96]
RWARNING
LOCK position does not lock the gearshift on
floor-mounted manual transaxle gearshifts. If the parking
brake is not set and the gearshift is moved out of gear,
your vehicle may move unexpectedly and injure someone.
*
[CF20470(R)05/96]
RWARNING
Do not leave the vehicle unattended with the transfer
case in the N (Neutral) position. Always set the parking
brake fully and turn off the ignition when leaving the
vehicle.
*
[CF20480(R)01/96]
LOCK is the only position that allows you to remove the key.
The LOCK feature helps to protect your vehicle from theft.
*
[CF20482(R)01/96]
If your key is stuck in the LOCK position and will not turn,
move your steering wheel left or right until the key turns freely.
*
[CF20484(R)01/96]
OFF allows you to shut off the engine and all accessories
without locking the steering wheel or the automatic
transmission gearshift lever.
*
[CF20486(R)01/96]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[CF20490(R)01/96]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997
Page 154 of 361
Starting
153
*
[TO10400(R)01/96]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning system to
bring in outside air.
[TO10650(R)01/96]
n
HEATING Ð Set fan speed to medium or high, the function
control knob on any position except OFF and the
temperature control knob on any desired position.
[TO10700(R)01/96]
n
AIR CONDITIONING Ð Set fan speed to medium or high
with the function control knob on any position (except OFF
or MAX A/C) and the temperature control knob at a
comfortable level.
*
[TO13076(R)03/96]
Removing the Key From the Ignition
*
[TO13100(R)03/96]
Procedures for removing your key from the ignition will vary,
depending on the type of gearshift your vehicle has. Gearshift
levers may be mounted on the steering column or on the floor
or console.
[TO13117(R)01/96]
If you have a manual transmission, you have a key release lever
which allows you to remove your key from the ignition. The
key release lever is on the upper right of the steering column,
just above the key lock cylinder.
*
[TO13300(R)03/96]
If your vehicle's gearshift lever is mounted on the
column:
*
[TO13400(R)03/96]1.
Put the gearshift in P (Park).
*
[TO13500(R)03/96]2.
Set the parking brake fully before removing your foot from
the service brake. (This will avoid ªbindingº or ªloadingº the
park gear if you park on a grade.)
*
[TO13600(R)03/96]3.
Turn the ignition key to LOCK.
*
[TO13700(R)03/96]4.
Remove the key.
File:08untor.ex
Update:Thu Mar 20 08:53:27 1997
Page 183 of 361
182
[GF17140(R)05/96]
NOTE: Do not drive the vehicle with the left and right
manual locking hubs set to different positions.
*
[GF17150(R)05/96]
To shift from 4H to 2H:
*
[GF17160(R)05/96]
Move the transfer case shift lever forward to the 2H position.
This can be done at any speed. However, the front driveline
will remain engaged to the front wheels until the manual
locking hubs are disengaged. To disengage the manual locking
hubs, stop the vehicle and rotate both hub lock selector knobs
counterclockwise to the FREE position.
*
[GF17170(R)05/96]
Operating in 2H with the hubs in the LOCK position increases
fuel consumption, noise, vibration, and wear. For prolonged 2H
operation on dry pavement, set the manual locking hubs to the
FREE position.
*
[GF17180(R)05/96]
To shift between 4H and 4L:
[GF17190(R)05/96]
Stop the vehicle and place the automatic transmission into N
(Neutral) or depress the clutch on vehicles with a manual
transmission. Pull the transfer case shift lever to the left and
shift the transfer case to the desired 4H or 4L position. This
shift should be with one continuous motion without pausing in
the N position. Pausing in the neutral position can result in gear
clash and difficult shifting. If while shifting between 4H and 4L,
the transfer case gets stuck in the N position or is difficult to
shift into either 4H or 4L, it may be necessary to let the vehicle
roll slightly and/or turn off the engine (particularly on vehicles
equipped with automatic transmissions).
[GF17200(R)05/96]
To shift between N (Neutral) and either 4H or 4L
[GF17210(R)05/96]
To shift into N (Neutral), stop the vehicle and engage the
parking brake. Place the automatic transmission into N (Neutral)
or depress the clutch on manual transmission vehicles. From
either the 4H or 4L position, pull the transfer case shift lever to
the left and move the transfer case shift lever to the N (Neutral)
position. The N (Neutral) position should only be used for
vehicle towing.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997
Page 240 of 361
Roadside Emergencies
239
%*
[ER25100(R)02/96]
Preparing Your Vehicle
*
[ER25200(R)02/96]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[ER25300(R)02/96]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[ER25400(R)02/96]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[ER25500(R)02/96]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[ER25600(R)02/96]5.
Turn on the heater fan in both vehicles. Turning on the fan
helps protect the electrical system from voltage surges. Turn
off all other switches and lights in both vehicles to prevent
possible damage to either vehicle's electrical systems.
%*
[ER25700(R)02/96]
Connecting the jumper cables
*
[ER25800(R)02/96]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[ER25900(R)02/96]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[ER26000(R)02/96]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997
Page 246 of 361
Roadside Emergencies
245
[ER33000(R)01/96]
4x2ÐManualtransmission
*
[ER33100(R)01/96]
n
Release the parking brake.
[ER33200(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33300(R)01/96]
n
Maximum speed is limited by towing equipment
manufacturer's recommendation, unlimited distance.
[ER33400(R)01/96]
4x4ÐManualshifttransfercase
*
[ER33500(R)01/96]
n
Release the parking brake.
[ER33600(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33700(R)01/96]
n
Place the transfer case gearshift in the neutral position.
[ER33800(R)01/96]
n
Set the manual locking hubs in the FREE position.
[ER33900(R)01/96]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[ER34000(R)01/96]
4 x 4 Electric shift transfer case
*
[ER34200(R)01/96]
n
Release the parking brake.
[ER34300(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER34400(R)05/96]
n
Ensure the transfer case is in 2H and the auto hubs are
unlocked.
[ER34600(R)01/96]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument panel will be off when the 4WD switch is
in 2WD.
[ER34700(R)01/96]
For automatic transmissions:
[ER34800(R)01/96]
n
Maximum speed is 35 mph (56 km/h).
[ER34900(R)01/96]
n
Maximum distance is 50 miles (80 km).
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997
Page 250 of 361
250
%*
[MC01400(R)05/96]
NOTE: Always dispose of used automotive fluids in a
responsible manner. Follow your community's
standards for disposing of these types of fluids. Call
your local recycling center to find out about recycling
automotive fluids.
%*
[MC01600(R)01/96]
Precautions When Servicing Your Vehicle
*
[MC01700(R)01/96]
Be especially careful when inspecting or servicing your vehicle.
Here are some general precautions for your safety:
*
[MC01900(R)01/96]
n
If you must work with the engine running, avoid wearing
loose clothing or jewelry that could get caught in moving
parts. Take appropriate precautions with long hair.
*
[MC02000(R)01/96]
n
Do not work on a vehicle in an enclosed space with the
engine running, unless you are sure you have enough
ventilation.
*
[MC02100(R)01/96]
n
Never get under a vehicle while it is supported only by a
jack. If you must work under a vehicle, use safety stands.
*
[MC02200(R)01/96]
n
Keep all lit cigarettes and other smoking materials away
from the battery and all fuel-related parts.
*
[MC02500(R)01/96]
If you disconnect the battery, the engine must ªrelearnº its idle
conditions before your vehicle will drive properly. To find out
how the engine does this, seeBatteryin this chapter.
*
[MC02600(R)01/96]
Working with the engine off:
*
[MC02660(R)01/96]1.
Set the parking brake fully and make sure that the gearshift
is securely latched in P (Park).
*
[MC02700(R)01/96]2.
Remove the key from the ignition after you turn the engine
off.
*
[MC02725(R)01/96]3.
Block the wheels. This will prevent your vehicle from
moving unexpectedly.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997
Page 258 of 361
258
*
[MC13730(R)05/96]
NOTE: Ford production and aftermarket (Motorcraft) oil
filters are designed for added engine protection and
long life. If a replacement oil filter is used that does
not meet Ford material and design specifications,
startup engine noises or knock may be experienced. It
is recommended you use the appropriate Motorcraft
oil filter (or another brand meeting Ford
specifications) for your engine application.
%*
[MC13775(R)01/96]
Checking and Adding Engine Oil
*
[MC13800(R)01/96]
Since the proper amount of engine oil is important for safe
engine operation, check the oil using the dipstick each time you
put fuel in your vehicle. Remember the engine must be off, the
oil must be warm and the vehicle must be parked on level
ground.
%*
[MC13900(R)01/96]
Checking the engine oil level:
*
[MC14000(R)01/96]1.
Turn the engine off after it has warmed up and allow a few
minutes for the engine oil to drain back into the oil pan.
[MC14050(R)04/96]2.
Set the parking brake, making sure the gearshift is securely
latched in P (Park) or 1 (manual transmission).
*
[MC14100(R)01/96]3.
Open the hood. Protect yourself from engine heat.
*
[MC14200(R)01/96]4.
Locate the engine oil dipstick (highlighted in yellow) and
carefully pull it out of the engine.
*
[MC14300(R)01/96]5.
Wipe the dipstick clean and put it back into position, making
sure it is fully seated.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997
Page 309 of 361
Maintenance and Care
309
*
[MC58100(R)01/96]
A volatile corrosion inhibitor added to the fuel system will
protect the fuel system's inner surfaces from corrosion. Follow
the instructions packaged with the product.
%*
[MC58200(R)01/96]
Cooling system
*
[MC58300(R)01/96]
n
Protect against freezing temperatures.
%*
[MC58400(R)01/96]
Battery
*
[MC58500(R)01/96]
n
Check and recharge as necessary.
*
[MC58600(R)01/96]
n
Keep connections clean and covered with a light coat of
grease.
%*
[MC58700(R)01/96]
Brakes
*
[MC58800(R)01/96]
n
Make sure brakes and parking brake are fully released.
%*
[MC58900(R)01/96]
Tires
*
[MC59000(R)01/96]
n
Maintain recommended air pressure.
*
[MC59100(R)01/96]
Miscellaneous
*
[MC59200(R)01/96]
n
Make sure all linkages, cables, levers and clevis pins under
vehicle are covered with grease to prevent rust.
*
[MC59300(R)01/96]
n
Move vehicles at least 25 feet (8 m) every 15 days to
lubricate working parts and prevent corrosion.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997